Zero Sequence Impedance using Zero Sequence Voltage (Two Conductor Open) Calculator

✖Zero Sequence Voltage in TCO is consists of a balanced three-phase voltage and current, phasors of which all have the same phase angles and rotate counterclockwise together.ⓘ Zero Sequence Voltage in TCO [V_0(tco)]			+10% -10%
✖Zero Sequence Current in TCO is consists of a balanced three-phase current, phasors of which all have the same phase angles and rotate counterclockwise together.ⓘ Zero Sequence Current in TCO [I_0(tco)]			+10% -10%

✖Zero Sequence Impedance in TCO is consists of a balanced three-phase voltage and current, phasors of which all have the same phase angles and rotate counter clockwise together.ⓘ Zero Sequence Impedance using Zero Sequence Voltage (Two Conductor Open) [Z_0(tco)]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Open Conductor Fault Formulas PDF PDF Image

Zero Sequence Impedance using Zero Sequence Voltage (Two Conductor Open) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Zero Sequence Impedance in TCO = (-1)*Zero Sequence Voltage in TCO/Zero Sequence Current in TCO
Z_0(tco) = (-1)*V_0(tco)/I_0(tco)
This formula uses 3 Variables

Variables Used

Zero Sequence Impedance in TCO - (Measured in Ohm) - Zero Sequence Impedance in TCO is consists of a balanced three-phase voltage and current, phasors of which all have the same phase angles and rotate counter clockwise together.
Zero Sequence Voltage in TCO - (Measured in Volt) - Zero Sequence Voltage in TCO is consists of a balanced three-phase voltage and current, phasors of which all have the same phase angles and rotate counterclockwise together.
Zero Sequence Current in TCO - (Measured in Ampere) - Zero Sequence Current in TCO is consists of a balanced three-phase current, phasors of which all have the same phase angles and rotate counterclockwise together.

STEP 1: Convert Input(s) to Base Unit

Zero Sequence Voltage in TCO: -17.5 Volt --> -17.5 Volt No Conversion Required
Zero Sequence Current in TCO: 2.19 Ampere --> 2.19 Ampere No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

Z_0(tco) = (-1)*V_0(tco)/I_0(tco) --> (-1)*(-17.5)/2.19

Evaluating ... ...

Z_0(tco) = 7.99086757990868

STEP 3: Convert Result to Output's Unit

7.99086757990868 Ohm --> No Conversion Required

FINAL ANSWER

7.99086757990868 ≈ 7.990868 Ohm <-- Zero Sequence Impedance in TCO

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Electrical » Power System » Fault » Open Conductor Fault » Two Conductor Open » Zero Sequence » Zero Sequence Impedance using Zero Sequence Voltage (Two Conductor Open)

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< Zero Sequence Calculators

Zero Sequence Potential Difference (Two Conductor Open)

LaTeX Go Zero Sequence Potential Difference in TCO = ((-1)*Positive Sequence Potential Difference in TCO)-(Negative Sequence Potential Difference in TCO)

Zero Sequence Potential Difference using Potential Difference between B-Phase(Two Conductor Open)

LaTeX Go Zero Sequence Potential Difference in TCO = (Potential Difference between B Phase in TCO+Potential Difference between C Phase in TCO)/3

Zero Sequence Impedance using Zero Sequence Voltage (Two Conductor Open)

LaTeX Go Zero Sequence Impedance in TCO = (-1)*Zero Sequence Voltage in TCO/Zero Sequence Current in TCO

Zero Sequence Voltage using Zero Sequence Current (Two Conductor Open)

LaTeX Go Zero Sequence Voltage in TCO = (-1)*Zero Sequence Current in TCO*Zero Sequence Impedance in TCO

Zero Sequence Impedance using Zero Sequence Voltage (Two Conductor Open) Formula

LaTeX Go

Zero Sequence Impedance in TCO = (-1)*Zero Sequence Voltage in TCO/Zero Sequence Current in TCO
Z_0(tco) = (-1)*V_0(tco)/I_0(tco)

Define two conductor open fault?

When two phases of a balanced three-phase line open it creates an unbalance in the system and results in the flow of unbalanced currents. Such conditions occur in the system when one or two conductors of a transmission line are broken due to storms or if fuses, isolators, or circuit breakers operate only on one or two phases leaving others connected.

How to Calculate Zero Sequence Impedance using Zero Sequence Voltage (Two Conductor Open)?

Zero Sequence Impedance using Zero Sequence Voltage (Two Conductor Open) calculator uses Zero Sequence Impedance in TCO = (-1)*Zero Sequence Voltage in TCO/Zero Sequence Current in TCO to calculate the Zero Sequence Impedance in TCO, The Zero Sequence Impedance using Zero Sequence Voltage (Two conductor open) formula is consists of a balanced three-phase impedance, phasors of which all have the same phase angles and rotate counterclockwise together. Zero Sequence Impedance in TCO is denoted by Z_0(tco) symbol.

How to calculate Zero Sequence Impedance using Zero Sequence Voltage (Two Conductor Open) using this online calculator? To use this online calculator for Zero Sequence Impedance using Zero Sequence Voltage (Two Conductor Open), enter Zero Sequence Voltage in TCO (V_0(tco)) & Zero Sequence Current in TCO (I_0(tco)) and hit the calculate button. Here is how the Zero Sequence Impedance using Zero Sequence Voltage (Two Conductor Open) calculation can be explained with given input values -> 7.990868 = (-1)*(-17.5)/2.19.

FAQ

What is Zero Sequence Impedance using Zero Sequence Voltage (Two Conductor Open)?

The Zero Sequence Impedance using Zero Sequence Voltage (Two conductor open) formula is consists of a balanced three-phase impedance, phasors of which all have the same phase angles and rotate counterclockwise together and is represented as Z_0(tco) = (-1)*V_0(tco)/I_0(tco) or Zero Sequence Impedance in TCO = (-1)*Zero Sequence Voltage in TCO/Zero Sequence Current in TCO. Zero Sequence Voltage in TCO is consists of a balanced three-phase voltage and current, phasors of which all have the same phase angles and rotate counterclockwise together & Zero Sequence Current in TCO is consists of a balanced three-phase current, phasors of which all have the same phase angles and rotate counterclockwise together.

How to calculate Zero Sequence Impedance using Zero Sequence Voltage (Two Conductor Open)?

The Zero Sequence Impedance using Zero Sequence Voltage (Two conductor open) formula is consists of a balanced three-phase impedance, phasors of which all have the same phase angles and rotate counterclockwise together is calculated using Zero Sequence Impedance in TCO = (-1)*Zero Sequence Voltage in TCO/Zero Sequence Current in TCO. To calculate Zero Sequence Impedance using Zero Sequence Voltage (Two Conductor Open), you need Zero Sequence Voltage in TCO (V_0(tco)) & Zero Sequence Current in TCO (I_0(tco)). With our tool, you need to enter the respective value for Zero Sequence Voltage in TCO & Zero Sequence Current in TCO and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search