Work Done Per Minute for Belt Transmission Dynamometer Calculator

✖Tension in Tight Side of Belt is the force exerted on the tight side of a belt in a pulley system, affecting the work done by the belt.ⓘ Tension in Tight Side of Belt [T₁]			+10% -10%
✖Tension in Slack Side of Belt is the force exerted by the slack side of a belt in a pulley system, affecting the work done by the belt.ⓘ Tension in Slack Side of Belt [T₂]			+10% -10%
✖Diameter of the Driving Pulley is the diameter of the pulley that drives the motion of the system, affecting the work done by the system.ⓘ Diameter of The Driving Pulley [D]			+10% -10%
✖Speed of Shaft in RPM is the number of turns of the shaft divided by time, specified as revolutions per minute (rpm), cycles per second (cps), radians per second (rad/s), etc.ⓘ Speed of Shaft in RPM [N]			+10% -10%

✖Work Done Per Minute is the amount of energy transferred or converted per unit of time, typically measured in joules per minute.ⓘ Work Done Per Minute for Belt Transmission Dynamometer [w]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Brakes and Dynamometers Formula PDF PDF Image

Work Done Per Minute for Belt Transmission Dynamometer Solution

STEP 0: Pre-Calculation Summary

Formula Used

Work Done Per Minute = (Tension in Tight Side of Belt-Tension in Slack Side of Belt)*pi*Diameter of The Driving Pulley*Speed of Shaft in RPM
w = (T₁-T₂)*pi*D*N
This formula uses 1 Constants, 5 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Variables Used

Work Done Per Minute - (Measured in Joule) - Work Done Per Minute is the amount of energy transferred or converted per unit of time, typically measured in joules per minute.
Tension in Tight Side of Belt - (Measured in Newton) - Tension in Tight Side of Belt is the force exerted on the tight side of a belt in a pulley system, affecting the work done by the belt.
Tension in Slack Side of Belt - (Measured in Newton) - Tension in Slack Side of Belt is the force exerted by the slack side of a belt in a pulley system, affecting the work done by the belt.
Diameter of The Driving Pulley - (Measured in Meter) - Diameter of the Driving Pulley is the diameter of the pulley that drives the motion of the system, affecting the work done by the system.
Speed of Shaft in RPM - Speed of Shaft in RPM is the number of turns of the shaft divided by time, specified as revolutions per minute (rpm), cycles per second (cps), radians per second (rad/s), etc.

STEP 1: Convert Input(s) to Base Unit

Tension in Tight Side of Belt: 24.263 Newton --> 24.263 Newton No Conversion Required
Tension in Slack Side of Belt: 11 Newton --> 11 Newton No Conversion Required
Diameter of The Driving Pulley: 6 Meter --> 6 Meter No Conversion Required
Speed of Shaft in RPM: 0.048 --> No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

w = (T₁-T₂)*pi*D*N --> (24.263-11)*pi*6*0.048

Evaluating ... ...

w = 12.0000796889937

STEP 3: Convert Result to Output's Unit

12.0000796889937 Joule --> No Conversion Required

FINAL ANSWER

12.0000796889937 ≈ 12.00008 Joule <-- Work Done Per Minute

(Calculation completed in 00.011 seconds)

You are here -

Home » Physics » Theory of Machine » Brakes and Dynamometers » Mechanical » Work Done » Work Done Per Minute for Belt Transmission Dynamometer

Credits

Created by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has created this Calculator and 2000+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< Work Done Calculators

Work Done Per Minute for Rope Brake Dynamometer

LaTeX Go Work Done Per Minute = (Dead Load-Spring Balance Reading)*pi*(Diameter of Wheel+Diameter of Rope)*Speed of Shaft in RPM

Work Done in One Revolution for Belt Transmission Dynamometer

LaTeX Go Work = (Tension in Tight Side of Belt-Tension in Slack Side of Belt)*pi*Diameter of The Driving Pulley

Work Done Per Minute for Prony Brake Dynamometer

LaTeX Go Work Done Per Minute = Torque Exerted on Wheel*2*pi*Speed of Shaft in RPM

Work Done in One Revolution for Prony Brake Dynamometer

LaTeX Go Work = Torque Exerted on Wheel*2*pi

Work Done Per Minute for Belt Transmission Dynamometer Formula

LaTeX Go

Work Done Per Minute = (Tension in Tight Side of Belt-Tension in Slack Side of Belt)*pi*Diameter of The Driving Pulley*Speed of Shaft in RPM
w = (T₁-T₂)*pi*D*N

What is Transmission Dynamometer?

A belt transmission dynamometer consists of the driving pulley, rigidly fixed to the shaft of the prime mover. There is another driven pulley mounted on another shaft, to which the power from the pulley is transmitted.

How to Calculate Work Done Per Minute for Belt Transmission Dynamometer?

Work Done Per Minute for Belt Transmission Dynamometer calculator uses Work Done Per Minute = (Tension in Tight Side of Belt-Tension in Slack Side of Belt)*pi*Diameter of The Driving Pulley*Speed of Shaft in RPM to calculate the Work Done Per Minute, Work Done Per Minute for Belt Transmission Dynamometer formula is defined as a measure of the rate at which work is done by a belt transmission dynamometer, which is a device used to measure the torque and rotational speed of a rotating shaft. It is an important parameter in evaluating the performance of a dynamometer. Work Done Per Minute is denoted by w symbol.

How to calculate Work Done Per Minute for Belt Transmission Dynamometer using this online calculator? To use this online calculator for Work Done Per Minute for Belt Transmission Dynamometer, enter Tension in Tight Side of Belt (T₁), Tension in Slack Side of Belt (T₂), Diameter of The Driving Pulley (D) & Speed of Shaft in RPM (N) and hit the calculate button. Here is how the Work Done Per Minute for Belt Transmission Dynamometer calculation can be explained with given input values -> 125000.8 = (24.263-11)*pi*6*0.048.

FAQ

What is Work Done Per Minute for Belt Transmission Dynamometer?

Work Done Per Minute for Belt Transmission Dynamometer formula is defined as a measure of the rate at which work is done by a belt transmission dynamometer, which is a device used to measure the torque and rotational speed of a rotating shaft. It is an important parameter in evaluating the performance of a dynamometer and is represented as w = (T₁-T₂)*pi*D*N or Work Done Per Minute = (Tension in Tight Side of Belt-Tension in Slack Side of Belt)*pi*Diameter of The Driving Pulley*Speed of Shaft in RPM. Tension in Tight Side of Belt is the force exerted on the tight side of a belt in a pulley system, affecting the work done by the belt, Tension in Slack Side of Belt is the force exerted by the slack side of a belt in a pulley system, affecting the work done by the belt, Diameter of the Driving Pulley is the diameter of the pulley that drives the motion of the system, affecting the work done by the system & Speed of Shaft in RPM is the number of turns of the shaft divided by time, specified as revolutions per minute (rpm), cycles per second (cps), radians per second (rad/s), etc.

How to calculate Work Done Per Minute for Belt Transmission Dynamometer?

Work Done Per Minute for Belt Transmission Dynamometer formula is defined as a measure of the rate at which work is done by a belt transmission dynamometer, which is a device used to measure the torque and rotational speed of a rotating shaft. It is an important parameter in evaluating the performance of a dynamometer is calculated using Work Done Per Minute = (Tension in Tight Side of Belt-Tension in Slack Side of Belt)*pi*Diameter of The Driving Pulley*Speed of Shaft in RPM. To calculate Work Done Per Minute for Belt Transmission Dynamometer, you need Tension in Tight Side of Belt (T₁), Tension in Slack Side of Belt (T₂), Diameter of The Driving Pulley (D) & Speed of Shaft in RPM (N). With our tool, you need to enter the respective value for Tension in Tight Side of Belt, Tension in Slack Side of Belt, Diameter of The Driving Pulley & Speed of Shaft in RPM and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Work Done Per Minute?

In this formula, Work Done Per Minute uses Tension in Tight Side of Belt, Tension in Slack Side of Belt, Diameter of The Driving Pulley & Speed of Shaft in RPM. We can use 2 other way(s) to calculate the same, which is/are as follows -

Work Done Per Minute = Torque Exerted on Wheel*2*pi*Speed of Shaft in RPM
Work Done Per Minute = (Dead Load-Spring Balance Reading)*pi*(Diameter of Wheel+Diameter of Rope)*Speed of Shaft in RPM

Home

FREE PDFs

🔍 Search