WAS Pumping Rate using Wasting Rate from Return Line when Concentration of Solid in Effluent is Low Calculator

✖Reactor Volume refers to the physical volume of a reactor used in chemical processes.ⓘ Reactor Volume [V]			+10% -10%
✖MLSS is the sum of volatile suspended solids (organics) and fixed suspended solids (inorganics).ⓘ MLSS [X]			+10% -10%
✖Mean Cell Residence Time is the average time that the sludge remains in the reactor.ⓘ Mean Cell Residence Time [θ_c]			+10% -10%
✖Sludge Concentration in Return Line refers to the concentration of suspended solids in the sludge that is being pumped back from the secondary clarifier to the aeration tank.ⓘ Sludge Concentration in Return Line [X_r]			+10% -10%

✖WAS Pumping Rate from Reactor is the total amount of waste activated sludge that comes out from the reactor.ⓘ WAS Pumping Rate using Wasting Rate from Return Line when Concentration of Solid in Effluent is Low [Q_w]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Pumping Rate Formulas PDF PDF Image

WAS Pumping Rate using Wasting Rate from Return Line when Concentration of Solid in Effluent is Low Solution

STEP 0: Pre-Calculation Summary

Formula Used

WAS Pumping Rate from Reactor = Reactor Volume*MLSS/(Mean Cell Residence Time*Sludge Concentration in Return Line)
Q_w = V*X/(θ_c*X_r)
This formula uses 5 Variables

Variables Used

WAS Pumping Rate from Reactor - (Measured in Cubic Meter per Second) - WAS Pumping Rate from Reactor is the total amount of waste activated sludge that comes out from the reactor.
Reactor Volume - (Measured in Cubic Meter) - Reactor Volume refers to the physical volume of a reactor used in chemical processes.
MLSS - (Measured in Kilogram per Cubic Meter) - MLSS is the sum of volatile suspended solids (organics) and fixed suspended solids (inorganics).
Mean Cell Residence Time - (Measured in Second) - Mean Cell Residence Time is the average time that the sludge remains in the reactor.
Sludge Concentration in Return Line - (Measured in Kilogram per Cubic Meter) - Sludge Concentration in Return Line refers to the concentration of suspended solids in the sludge that is being pumped back from the secondary clarifier to the aeration tank.

STEP 1: Convert Input(s) to Base Unit

Reactor Volume: 1000 Cubic Meter --> 1000 Cubic Meter No Conversion Required
MLSS: 1200 Milligram per Liter --> 1.2 Kilogram per Cubic Meter (Check conversion here)
Mean Cell Residence Time: 7 Day --> 604800 Second (Check conversion here)
Sludge Concentration in Return Line: 200 Milligram per Liter --> 0.2 Kilogram per Cubic Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

Q_w = V*X/(θ_c*X_r) --> 1000*1.2/(604800*0.2)

Evaluating ... ...

Q_w = 0.00992063492063492

STEP 3: Convert Result to Output's Unit

0.00992063492063492 Cubic Meter per Second -->857.142857142857 Cubic Meter per Day (Check conversion here)

FINAL ANSWER

857.142857142857 ≈ 857.1429 Cubic Meter per Day <-- WAS Pumping Rate from Reactor

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Civil » Environmental Engineering » Design of a Complete Mix Activated Sludge Reactor » Pumping Rate » WAS Pumping Rate » WAS Pumping Rate using Wasting Rate from Return Line when Concentration of Solid in Effluent is Low

Credits

Created by Ishita Goyal

Meerut Institute of Engineering and Technology (MIET), Meerut

Ishita Goyal has created this Calculator and 500+ more calculators!

Verified by Chandana P Dev

NSS College of Engineering (NSSCE), Palakkad

Chandana P Dev has verified this Calculator and 1700+ more calculators!

< WAS Pumping Rate Calculators

WAS Pumping Rate from Return Line given Wasting Rate from Return Line

LaTeX Go WAS Pumping Rate from Reactor = (Reactor Volume*MLSS/(Mean Cell Residence Time*Sludge Concentration in Return Line))-(Effluent Flow Rate*Solid Concentration in Effluent/Sludge Concentration in Return Line)

WAS Pumping Rate from Return Line given RAS Pumping Rate from Aeration Tank

LaTeX Go WAS Pumping Rate from Reactor = ((MLSS/Sludge Concentration in Return Line)*(Average Daily Influent Flow Rate+Return Activated Sludge))-Return Activated Sludge

WAS Pumping Rate using Wasting Rate from Return Line when Concentration of Solid in Effluent is Low

LaTeX Go WAS Pumping Rate from Reactor = Reactor Volume*MLSS/(Mean Cell Residence Time*Sludge Concentration in Return Line)

WAS Pumping Rate from Aeration Tank

LaTeX Go WAS Pumping Rate from Reactor = Reactor Volume/Mean Cell Residence Time

WAS Pumping Rate using Wasting Rate from Return Line when Concentration of Solid in Effluent is Low Formula

LaTeX Go

WAS Pumping Rate from Reactor = Reactor Volume*MLSS/(Mean Cell Residence Time*Sludge Concentration in Return Line)
Q_w = V*X/(θ_c*X_r)

What is Wasting Rate?

The Wasting Rate from return line is the time required to waste sludge from the return sludge line because return activated sludge is more concentrated and requires smaller waste sludge pumps.

How to Calculate WAS Pumping Rate using Wasting Rate from Return Line when Concentration of Solid in Effluent is Low?

WAS Pumping Rate using Wasting Rate from Return Line when Concentration of Solid in Effluent is Low calculator uses WAS Pumping Rate from Reactor = Reactor Volume*MLSS/(Mean Cell Residence Time*Sludge Concentration in Return Line) to calculate the WAS Pumping Rate from Reactor, The WAS Pumping Rate using Wasting Rate from Return line when Concentration of Solid in Effluent is Low formula is defined as the rate at which waste activated sludge is removed from the secondary treatment system to control the biomass concentration and maintain the efficiency of the treatment process. WAS Pumping Rate from Reactor is denoted by Q_w symbol.

How to calculate WAS Pumping Rate using Wasting Rate from Return Line when Concentration of Solid in Effluent is Low using this online calculator? To use this online calculator for WAS Pumping Rate using Wasting Rate from Return Line when Concentration of Solid in Effluent is Low, enter Reactor Volume (V), MLSS (X), Mean Cell Residence Time (θ_c) & Sludge Concentration in Return Line (X_r) and hit the calculate button. Here is how the WAS Pumping Rate using Wasting Rate from Return Line when Concentration of Solid in Effluent is Low calculation can be explained with given input values -> 7.4E+7 = 1000*1.2/(604800*0.2).

FAQ

What is WAS Pumping Rate using Wasting Rate from Return Line when Concentration of Solid in Effluent is Low?

The WAS Pumping Rate using Wasting Rate from Return line when Concentration of Solid in Effluent is Low formula is defined as the rate at which waste activated sludge is removed from the secondary treatment system to control the biomass concentration and maintain the efficiency of the treatment process and is represented as Q_w = V*X/(θ_c*X_r) or WAS Pumping Rate from Reactor = Reactor Volume*MLSS/(Mean Cell Residence Time*Sludge Concentration in Return Line). Reactor Volume refers to the physical volume of a reactor used in chemical processes, MLSS is the sum of volatile suspended solids (organics) and fixed suspended solids (inorganics), Mean Cell Residence Time is the average time that the sludge remains in the reactor & Sludge Concentration in Return Line refers to the concentration of suspended solids in the sludge that is being pumped back from the secondary clarifier to the aeration tank.

How to calculate WAS Pumping Rate using Wasting Rate from Return Line when Concentration of Solid in Effluent is Low?

The WAS Pumping Rate using Wasting Rate from Return line when Concentration of Solid in Effluent is Low formula is defined as the rate at which waste activated sludge is removed from the secondary treatment system to control the biomass concentration and maintain the efficiency of the treatment process is calculated using WAS Pumping Rate from Reactor = Reactor Volume*MLSS/(Mean Cell Residence Time*Sludge Concentration in Return Line). To calculate WAS Pumping Rate using Wasting Rate from Return Line when Concentration of Solid in Effluent is Low, you need Reactor Volume (V), MLSS (X), Mean Cell Residence Time (θ_c) & Sludge Concentration in Return Line (X_r). With our tool, you need to enter the respective value for Reactor Volume, MLSS, Mean Cell Residence Time & Sludge Concentration in Return Line and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate WAS Pumping Rate from Reactor?

In this formula, WAS Pumping Rate from Reactor uses Reactor Volume, MLSS, Mean Cell Residence Time & Sludge Concentration in Return Line. We can use 3 other way(s) to calculate the same, which is/are as follows -

WAS Pumping Rate from Reactor = (Reactor Volume*MLSS/(Mean Cell Residence Time*Sludge Concentration in Return Line))-(Effluent Flow Rate*Solid Concentration in Effluent/Sludge Concentration in Return Line)
WAS Pumping Rate from Reactor = Reactor Volume/Mean Cell Residence Time
WAS Pumping Rate from Reactor = ((MLSS/Sludge Concentration in Return Line)*(Average Daily Influent Flow Rate+Return Activated Sludge))-Return Activated Sludge

Home

FREE PDFs

🔍 Search