Volume of crater made by electric spark Calculator

✖Depth of machined surface is the how deep a surface is machined from the un-machined surface.ⓘ Depth of Machined Surface [H_sd]			+10% -10%
✖The smaller diameter is the smaller of all diameters of a given object.ⓘ Smaller Diameter [d]			+10% -10%
✖Larger diameter is the bigger diameter of hole or other things.ⓘ Larger Diameter [D_sd]			+10% -10%

✖Volume of crater is defined as the Volume of crater made by an electric spark during EDM.ⓘ Volume of crater made by electric spark [V_sd]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Production Engineering Formula PDF PDF Image

Volume of crater made by electric spark Solution

STEP 0: Pre-Calculation Summary

Formula Used

Volume of Crater = (pi/12)*Depth of Machined Surface*((Smaller Diameter^2)+(Larger Diameter^2)+(Larger Diameter*Smaller Diameter))
V_sd = (pi/12)*H_sd*((d^2)+(D_sd^2)+(D_sd*d))
This formula uses 1 Constants, 4 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Variables Used

Volume of Crater - (Measured in Cubic Meter) - Volume of crater is defined as the Volume of crater made by an electric spark during EDM.
Depth of Machined Surface - (Measured in Meter) - Depth of machined surface is the how deep a surface is machined from the un-machined surface.
Smaller Diameter - (Measured in Meter) - The smaller diameter is the smaller of all diameters of a given object.
Larger Diameter - (Measured in Meter) - Larger diameter is the bigger diameter of hole or other things.

STEP 1: Convert Input(s) to Base Unit

Depth of Machined Surface: 52 Meter --> 52 Meter No Conversion Required
Smaller Diameter: 1.2 Meter --> 1.2 Meter No Conversion Required
Larger Diameter: 22 Meter --> 22 Meter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

V_sd = (pi/12)*H_sd*((d^2)+(D_sd^2)+(D_sd*d)) --> (pi/12)*52*((1.2^2)+(22^2)+(22*1.2))

Evaluating ... ...

V_sd = 6967.96872985806

STEP 3: Convert Result to Output's Unit

6967.96872985806 Cubic Meter --> No Conversion Required

FINAL ANSWER

6967.96872985806 ≈ 6967.969 Cubic Meter <-- Volume of Crater

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Production Engineering » Unconventional machining processes » Electro Discharge Machining (EDM) » Possible surface defects in EDM » Taper Formation » Volume of crater made by electric spark

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Taper Formation Calculators

Empirical constant for taper

LaTeX Go Empirical Constant = (Larger Diameter-Smaller Diameter)/(2*Depth of Machined Surface*Smaller Diameter^2)

Depth of machined surface

LaTeX Go Depth of Machined Surface = (Larger Diameter-Smaller Diameter)/(2*Empirical Constant*Smaller Diameter^2)

Upper diameter of hole

LaTeX Go Larger Diameter = 2*Depth of Machined Surface*Empirical Constant*Smaller Diameter^2+Smaller Diameter

Taper produced due to side sparks

LaTeX Go Taper Produced in EDM = Empirical Constant*Smaller Diameter^2

Volume of crater made by electric spark Formula

LaTeX Go

Volume of Crater = (pi/12)*Depth of Machined Surface*((Smaller Diameter^2)+(Larger Diameter^2)+(Larger Diameter*Smaller Diameter))
V_sd = (pi/12)*H_sd*((d^2)+(D_sd^2)+(D_sd*d))

What factors affects surface finish during EDM ?

The amount of material removed and the surface finish produced is dependent upon the current in the spark. The material removed by the spark can be assumed to be a crater. The amount removed therefore will depend upon the crater depth, which is directly proportional to the current. Thus as the material removed increases and at the same time the surface finish also decreases. However, decreasing the current in the spark, but increasing its frequency will improve the surface finish in view of the small crater size, but at the same time the material removal rate can be maintained by increasing the frequency.

How to Calculate Volume of crater made by electric spark?

Volume of crater made by electric spark calculator uses Volume of Crater = (pi/12)*Depth of Machined Surface*((Smaller Diameter^2)+(Larger Diameter^2)+(Larger Diameter*Smaller Diameter)) to calculate the Volume of Crater, The Volume of crater made by electric spark formula is defined as Volume of crater made by electric spark during EDM. Volume of Crater is denoted by V_sd symbol.

How to calculate Volume of crater made by electric spark using this online calculator? To use this online calculator for Volume of crater made by electric spark, enter Depth of Machined Surface (H_sd), Smaller Diameter (d) & Larger Diameter (D_sd) and hit the calculate button. Here is how the Volume of crater made by electric spark calculation can be explained with given input values -> 6967.969 = (pi/12)*52*((1.2^2)+(22^2)+(22*1.2)).

FAQ

What is Volume of crater made by electric spark?

The Volume of crater made by electric spark formula is defined as Volume of crater made by electric spark during EDM and is represented as V_sd = (pi/12)*H_sd*((d^2)+(D_sd^2)+(D_sd*d)) or Volume of Crater = (pi/12)*Depth of Machined Surface*((Smaller Diameter^2)+(Larger Diameter^2)+(Larger Diameter*Smaller Diameter)). Depth of machined surface is the how deep a surface is machined from the un-machined surface, The smaller diameter is the smaller of all diameters of a given object & Larger diameter is the bigger diameter of hole or other things.

How to calculate Volume of crater made by electric spark?

The Volume of crater made by electric spark formula is defined as Volume of crater made by electric spark during EDM is calculated using Volume of Crater = (pi/12)*Depth of Machined Surface*((Smaller Diameter^2)+(Larger Diameter^2)+(Larger Diameter*Smaller Diameter)). To calculate Volume of crater made by electric spark, you need Depth of Machined Surface (H_sd), Smaller Diameter (d) & Larger Diameter (D_sd). With our tool, you need to enter the respective value for Depth of Machined Surface, Smaller Diameter & Larger Diameter and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search