Volume of Conductor Material using Line Losses (Single Phase Two Wire Mid-Point OS) Calculator

✖Resistivity is the measure of how strongly a material opposes the flow of current through them.ⓘ Resistivity [ρ]			+10% -10%
✖Power Transmitted is defined as the product of current and voltage phasor in a overhead ac line at the receiving end.ⓘ Power Transmitted [P]			+10% -10%
✖Length of Overhead AC Wire is the total length of the wire from one end to other end.ⓘ Length of Overhead AC Wire [L]			+10% -10%
✖Line Losses is defined as the total losses occurring in an Overhead AC line when in use.ⓘ Line Losses [P_loss]			+10% -10%
✖Maximum Voltage Overhead AC is defined as the peak amplitude of the AC voltage supplied to the line or wire.ⓘ Maximum Voltage Overhead AC [V_m]			+10% -10%
✖Phase Difference is defined as the difference between the phasor of apparent and real power (in degrees) or between voltage and current in an ac circuit.ⓘ Phase Difference [Φ]			+10% -10%

✖Volume of Conductor is the total volume of the material used to make the conductor of an overhead ac line.ⓘ Volume of Conductor Material using Line Losses (Single Phase Two Wire Mid-Point OS) [V]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Power System Formula PDF PDF Image

Volume of Conductor Material using Line Losses (Single Phase Two Wire Mid-Point OS) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Volume of Conductor = (2*Resistivity*Power Transmitted^2*Length of Overhead AC Wire^2)/(Line Losses*Maximum Voltage Overhead AC*cos(Phase Difference)^2)
V = (2*ρ*P^2*L^2)/(P_loss*V_m*cos(Φ)^2)
This formula uses 1 Functions, 7 Variables

Functions Used

cos - Cosine of an angle is the ratio of the side adjacent to the angle to the hypotenuse of the triangle., cos(Angle)

Variables Used

Volume of Conductor - (Measured in Cubic Meter) - Volume of Conductor is the total volume of the material used to make the conductor of an overhead ac line.
Resistivity - (Measured in Ohm Meter) - Resistivity is the measure of how strongly a material opposes the flow of current through them.
Power Transmitted - (Measured in Watt) - Power Transmitted is defined as the product of current and voltage phasor in a overhead ac line at the receiving end.
Length of Overhead AC Wire - (Measured in Meter) - Length of Overhead AC Wire is the total length of the wire from one end to other end.
Line Losses - (Measured in Watt) - Line Losses is defined as the total losses occurring in an Overhead AC line when in use.
Maximum Voltage Overhead AC - (Measured in Volt) - Maximum Voltage Overhead AC is defined as the peak amplitude of the AC voltage supplied to the line or wire.
Phase Difference - (Measured in Radian) - Phase Difference is defined as the difference between the phasor of apparent and real power (in degrees) or between voltage and current in an ac circuit.

STEP 1: Convert Input(s) to Base Unit

Resistivity: 1.7E-05 Ohm Meter --> 1.7E-05 Ohm Meter No Conversion Required
Power Transmitted: 890 Watt --> 890 Watt No Conversion Required
Length of Overhead AC Wire: 10.63 Meter --> 10.63 Meter No Conversion Required
Line Losses: 8.23 Watt --> 8.23 Watt No Conversion Required
Maximum Voltage Overhead AC: 62 Volt --> 62 Volt No Conversion Required
Phase Difference: 30 Degree --> 0.5235987755982 Radian (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

V = (2*ρ*P^2*L^2)/(P_loss*V_m*cos(Φ)^2) --> (2*1.7E-05*890^2*10.63^2)/(8.23*62*cos(0.5235987755982)^2)

Evaluating ... ...

V = 7.95193225064346

STEP 3: Convert Result to Output's Unit

7.95193225064346 Cubic Meter --> No Conversion Required

FINAL ANSWER

7.95193225064346 ≈ 7.951932 Cubic Meter <-- Volume of Conductor

(Calculation completed in 00.008 seconds)

You are here -

Home » Engineering » Electrical » Power System » Overhead AC Supply » 1 2 Wire Mid Point Earthed System » Wire Parameters » Volume of Conductor Material using Line Losses (Single Phase Two Wire Mid-Point OS)

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Kethavath Srinath

Osmania University (OU), Hyderabad

Kethavath Srinath has verified this Calculator and 1200+ more calculators!

< Wire Parameters Calculators

Length of Wire using Area of X-Section(Single Phase Two Wire Mid-Point Earthed OS)

LaTeX Go Length of Overhead AC Wire = (Area of Overhead AC Wire*Maximum Voltage Overhead AC^2*Line Losses*cos(Phase Difference)^2)/(Resistivity*Power Transmitted^2)

Line Losses using Area of X-Section(Single Phase Two Wire Mid-Point Earthed OS)

LaTeX Go Line Losses = (Length of Overhead AC Wire*Resistivity*Power Transmitted^2)/(Area of Overhead AC Wire*Maximum Voltage Overhead AC^2*cos(Phase Difference)^2)

Area of X-Section(Single Phase Two Wire Mid-Point Earthed)

LaTeX Go Area of Overhead AC Wire = (Power Transmitted^2*Resistivity*Length of Overhead AC Wire)/(((cos(Phase Difference))^2)*Line Losses*Voltage Overhead AC^2)

Constant (Single Phase Two Wire Mid-Point Earthed)

LaTeX Go Constant Overhead AC = (4*Power Transmitted^2*Resistivity*Length of Overhead AC Wire)/(Line Losses*Voltage Overhead AC^2)

Volume of Conductor Material using Line Losses (Single Phase Two Wire Mid-Point OS) Formula

LaTeX Go

Volume of Conductor = (2*Resistivity*Power Transmitted^2*Length of Overhead AC Wire^2)/(Line Losses*Maximum Voltage Overhead AC*cos(Phase Difference)^2)
V = (2*ρ*P^2*L^2)/(P_loss*V_m*cos(Φ)^2)

What is the value of maximum voltage and volume of conductor material in this system?

The volume of conductor material required in this system is 1/2cos²θ times that of 2-wire d.c.system with the one conductor earthed. The maximum voltage between conductors is 2v_m so that r.m.s. value of voltage between them is √2v_m.

How to Calculate Volume of Conductor Material using Line Losses (Single Phase Two Wire Mid-Point OS)?

Volume of Conductor Material using Line Losses (Single Phase Two Wire Mid-Point OS) calculator uses Volume of Conductor = (2*Resistivity*Power Transmitted^2*Length of Overhead AC Wire^2)/(Line Losses*Maximum Voltage Overhead AC*cos(Phase Difference)^2) to calculate the Volume of Conductor, The Volume of Conductor Material using Line Losses (single Phase two Wire Mid-Point OS) formula is defined as the 3-dimensional space enclosed by a conductor material of a single-phase two-wire mid-point earthed overhead system. Volume of Conductor is denoted by V symbol.

How to calculate Volume of Conductor Material using Line Losses (Single Phase Two Wire Mid-Point OS) using this online calculator? To use this online calculator for Volume of Conductor Material using Line Losses (Single Phase Two Wire Mid-Point OS), enter Resistivity (ρ), Power Transmitted (P), Length of Overhead AC Wire (L), Line Losses (P_loss), Maximum Voltage Overhead AC (V_m) & Phase Difference (Φ) and hit the calculate button. Here is how the Volume of Conductor Material using Line Losses (Single Phase Two Wire Mid-Point OS) calculation can be explained with given input values -> 7.951932 = (2*1.7E-05*890^2*10.63^2)/(8.23*62*cos(0.5235987755982)^2).

FAQ

What is Volume of Conductor Material using Line Losses (Single Phase Two Wire Mid-Point OS)?

The Volume of Conductor Material using Line Losses (single Phase two Wire Mid-Point OS) formula is defined as the 3-dimensional space enclosed by a conductor material of a single-phase two-wire mid-point earthed overhead system and is represented as V = (2*ρ*P^2*L^2)/(P_loss*V_m*cos(Φ)^2) or Volume of Conductor = (2*Resistivity*Power Transmitted^2*Length of Overhead AC Wire^2)/(Line Losses*Maximum Voltage Overhead AC*cos(Phase Difference)^2). Resistivity is the measure of how strongly a material opposes the flow of current through them, Power Transmitted is defined as the product of current and voltage phasor in a overhead ac line at the receiving end, Length of Overhead AC Wire is the total length of the wire from one end to other end, Line Losses is defined as the total losses occurring in an Overhead AC line when in use, Maximum Voltage Overhead AC is defined as the peak amplitude of the AC voltage supplied to the line or wire & Phase Difference is defined as the difference between the phasor of apparent and real power (in degrees) or between voltage and current in an ac circuit.

How to calculate Volume of Conductor Material using Line Losses (Single Phase Two Wire Mid-Point OS)?

The Volume of Conductor Material using Line Losses (single Phase two Wire Mid-Point OS) formula is defined as the 3-dimensional space enclosed by a conductor material of a single-phase two-wire mid-point earthed overhead system is calculated using Volume of Conductor = (2*Resistivity*Power Transmitted^2*Length of Overhead AC Wire^2)/(Line Losses*Maximum Voltage Overhead AC*cos(Phase Difference)^2). To calculate Volume of Conductor Material using Line Losses (Single Phase Two Wire Mid-Point OS), you need Resistivity (ρ), Power Transmitted (P), Length of Overhead AC Wire (L), Line Losses (P_loss), Maximum Voltage Overhead AC (V_m) & Phase Difference (Φ). With our tool, you need to enter the respective value for Resistivity, Power Transmitted, Length of Overhead AC Wire, Line Losses, Maximum Voltage Overhead AC & Phase Difference and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Volume of Conductor?

In this formula, Volume of Conductor uses Resistivity, Power Transmitted, Length of Overhead AC Wire, Line Losses, Maximum Voltage Overhead AC & Phase Difference. We can use 1 other way(s) to calculate the same, which is/are as follows -

Volume of Conductor = (4*(Current Overhead AC^2)*Resistivity*(Length of Overhead AC Wire^2))/(Line Losses)

Home

FREE PDFs

🔍 Search