Ultimate tensile strength of work piece material Calculator

✖Sparking time is defined as the time for which a spark is sustained.ⓘ Sparking time [τ_s]			+10% -10%
✖Mean current setting is the current set to mean current value during unconventional machining of EDM.ⓘ Mean Current Setting [I_m]			+10% -10%
✖Volume of crater is defined as the Volume of crater made by an electric spark during EDM.ⓘ Volume of Crater [V]			+10% -10%

✖Ultimate Tensile Strength (UTS) is the maximum stress that a material can withstand while being stretched or pulled.ⓘ Ultimate tensile strength of work piece material [S_ut]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Production Engineering Formula PDF PDF Image

Ultimate tensile strength of work piece material Solution

STEP 0: Pre-Calculation Summary

Formula Used

Ultimate Tensile Strength = (3.25*Sparking time*Mean Current Setting^(3/2))/Volume of Crater
S_ut = (3.25*τ_s*I_m^(3/2))/V
This formula uses 4 Variables

Variables Used

Ultimate Tensile Strength - (Measured in Pascal) - Ultimate Tensile Strength (UTS) is the maximum stress that a material can withstand while being stretched or pulled.
Sparking time - (Measured in Second) - Sparking time is defined as the time for which a spark is sustained.
Mean Current Setting - (Measured in Ampere) - Mean current setting is the current set to mean current value during unconventional machining of EDM.
Volume of Crater - (Measured in Square Meter) - Volume of crater is defined as the Volume of crater made by an electric spark during EDM.

STEP 1: Convert Input(s) to Base Unit

Sparking time: 8 Second --> 8 Second No Conversion Required
Mean Current Setting: 0.5 Ampere --> 0.5 Ampere No Conversion Required
Volume of Crater: 3 Square Millimeter --> 3E-06 Square Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

S_ut = (3.25*τ_s*I_m^(3/2))/V --> (3.25*8*0.5^(3/2))/3E-06

Evaluating ... ...

S_ut = 3064129.38514171

STEP 3: Convert Result to Output's Unit

3064129.38514171 Pascal -->3.06412938514171 Newton per Square Millimeter (Check conversion here)

FINAL ANSWER

3.06412938514171 ≈ 3.064129 Newton per Square Millimeter <-- Ultimate Tensile Strength

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Production Engineering » Unconventional machining processes » Electro Discharge Machining (EDM) » Volume of crater made by an electric spark » Ultimate tensile strength of work piece material

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Volume of crater made by an electric spark Calculators

Diameter of crater

LaTeX Go Larger Diameter = sqrt((8*(Volume of Crater-(pi/6)*Depth of Machined Surface^3))/(pi*Depth of Machined Surface))

Mean current setting from crater volume

LaTeX Go Mean Current Setting = ((Volume of Crater*Ultimate Tensile Strength)/(3.25*Sparking time))^(2/3)

Volume of crater related to mean current setting

LaTeX Go Volume of Crater = 3.25*10^6/Ultimate Tensile Strength*Sparking time*Mean Current Setting^(3/2)

Discharge duration of single pulse

LaTeX Go Sparking time = (Volume of Crater*Ultimate Tensile Strength)/(3.25*Mean Current Setting^(3/2))

Ultimate tensile strength of work piece material Formula

LaTeX Go

Ultimate Tensile Strength = (3.25*Sparking time*Mean Current Setting^(3/2))/Volume of Crater
S_ut = (3.25*τ_s*I_m^(3/2))/V

What factors affects surface finish during EDM ?

The amount of material removed and the surface finish produced is dependent upon the current in the spark. The material removed by the spark can be assumed to be a crater. The amount removed therefore will depend upon the crater depth, which is directly proportional to the current. Thus as the material removed increases and at the same time the surface finish also decreases. However, decreasing the current in the spark, but increasing its frequency will improve the surface finish in view of the small crater size, but at the same time the material removal rate can be maintained by increasing the frequency.

How to Calculate Ultimate tensile strength of work piece material?

Ultimate tensile strength of work piece material calculator uses Ultimate Tensile Strength = (3.25*Sparking time*Mean Current Setting^(3/2))/Volume of Crater to calculate the Ultimate Tensile Strength, The Ultimate tensile strength of work piece material formula is defined as the maximum stress that a material can withstand before failure. Ultimate Tensile Strength is denoted by S_ut symbol.

How to calculate Ultimate tensile strength of work piece material using this online calculator? To use this online calculator for Ultimate tensile strength of work piece material, enter Sparking time (τ_s), Mean Current Setting (I_m) & Volume of Crater (V) and hit the calculate button. Here is how the Ultimate tensile strength of work piece material calculation can be explained with given input values -> 1.8E-7 = (3.25*8*0.5^(3/2))/3E-06.

FAQ

What is Ultimate tensile strength of work piece material?

The Ultimate tensile strength of work piece material formula is defined as the maximum stress that a material can withstand before failure and is represented as S_ut = (3.25*τ_s*I_m^(3/2))/V or Ultimate Tensile Strength = (3.25*Sparking time*Mean Current Setting^(3/2))/Volume of Crater. Sparking time is defined as the time for which a spark is sustained, Mean current setting is the current set to mean current value during unconventional machining of EDM & Volume of crater is defined as the Volume of crater made by an electric spark during EDM.

How to calculate Ultimate tensile strength of work piece material?

The Ultimate tensile strength of work piece material formula is defined as the maximum stress that a material can withstand before failure is calculated using Ultimate Tensile Strength = (3.25*Sparking time*Mean Current Setting^(3/2))/Volume of Crater. To calculate Ultimate tensile strength of work piece material, you need Sparking time (τ_s), Mean Current Setting (I_m) & Volume of Crater (V). With our tool, you need to enter the respective value for Sparking time, Mean Current Setting & Volume of Crater and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search