Transmitted Power using Volume(Two-Wire One Conductor Earthed) Calculator

✖Volume of Conductor is the total volume of the material used to make the conductor of an overhead dc line.ⓘ Volume of Conductor [V]			+10% -10%
✖Line Losses is defined as the total losses occurring in an Overhead DC line when in use.ⓘ Line Losses [P_loss]			+10% -10%
✖Maximum Voltage Overhead DC is defined as the peak amplitude of the AC voltage supplied to the line or wire.ⓘ Maximum Voltage Overhead DC [V_m]			+10% -10%
✖Resistivity is the measure of how strongly a material opposes the flow of current through them.ⓘ Resistivity [ρ]			+10% -10%
✖Length of Wire DC is the total length of the wire from one end to other end.ⓘ Length of Wire DC [L]			+10% -10%

✖Power Transmitted is defined as the product of current and voltage phasor in a overhead dc line at the receiving end.ⓘ Transmitted Power using Volume(Two-Wire One Conductor Earthed) [P]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Power System Formula PDF PDF Image

Transmitted Power using Volume(Two-Wire One Conductor Earthed) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Power Transmitted = sqrt(Volume of Conductor*Line Losses*(Maximum Voltage Overhead DC^2)/(4*Resistivity*(Length of Wire DC^2)))
P = sqrt(V*P_loss*(V_m^2)/(4*ρ*(L^2)))
This formula uses 1 Functions, 6 Variables

Functions Used

sqrt - A square root function is a function that takes a non-negative number as an input and returns the square root of the given input number., sqrt(Number)

Variables Used

Power Transmitted - (Measured in Watt) - Power Transmitted is defined as the product of current and voltage phasor in a overhead dc line at the receiving end.
Volume of Conductor - (Measured in Cubic Meter) - Volume of Conductor is the total volume of the material used to make the conductor of an overhead dc line.
Line Losses - (Measured in Watt) - Line Losses is defined as the total losses occurring in an Overhead DC line when in use.
Maximum Voltage Overhead DC - (Measured in Volt) - Maximum Voltage Overhead DC is defined as the peak amplitude of the AC voltage supplied to the line or wire.
Resistivity - (Measured in Ohm Meter) - Resistivity is the measure of how strongly a material opposes the flow of current through them.
Length of Wire DC - (Measured in Meter) - Length of Wire DC is the total length of the wire from one end to other end.

STEP 1: Convert Input(s) to Base Unit

Volume of Conductor: 26 Cubic Meter --> 26 Cubic Meter No Conversion Required
Line Losses: 0.74 Watt --> 0.74 Watt No Conversion Required
Maximum Voltage Overhead DC: 60.26 Volt --> 60.26 Volt No Conversion Required
Resistivity: 1.7E-05 Ohm Meter --> 1.7E-05 Ohm Meter No Conversion Required
Length of Wire DC: 12.7 Meter --> 12.7 Meter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

P = sqrt(V*P_loss*(V_m^2)/(4*ρ*(L^2))) --> sqrt(26*0.74*(60.26^2)/(4*1.7E-05*(12.7^2)))

Evaluating ... ...

P = 2523.90778883202

STEP 3: Convert Result to Output's Unit

2523.90778883202 Watt --> No Conversion Required

FINAL ANSWER

2523.90778883202 ≈ 2523.908 Watt <-- Power Transmitted

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Power System » Overhead DC Supply » 2 Wire System » 1 Conductor Earthed » Power and Power Factor » Transmitted Power using Volume(Two-Wire One Conductor Earthed)

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Shobhit Dimri

Bipin Tripathi Kumaon Institute of Technology (BTKIT), Dwarahat

Shobhit Dimri has verified this Calculator and 100+ more calculators!

< Power and Power Factor Calculators

Power Transmitted using K(Two-Wire One Conductor Earthed)

LaTeX Go Power Transmitted = sqrt(Constant Overhead DC*Line Losses*(Maximum Voltage Overhead DC^2)/(4*Resistivity*(Length of Wire DC^2)))

Transmitted Power using Volume(Two-Wire One Conductor Earthed)

LaTeX Go Power Transmitted = sqrt(Volume of Conductor*Line Losses*(Maximum Voltage Overhead DC^2)/(4*Resistivity*(Length of Wire DC^2)))

Transmitted Power using Line Losses(Two-Wire One Conductor Earthed)

LaTeX Go Power Transmitted = sqrt((Line Losses*(Maximum Voltage Overhead DC^2))/(2*Resistance Overhead DC))

Transmitted Power using Load Current(Two-Wire One Conductor Earthed)

LaTeX Go Power Transmitted = Current Overhead DC*Maximum Voltage Overhead DC

Transmitted Power using Volume(Two-Wire One Conductor Earthed) Formula

LaTeX Go

Power Transmitted = sqrt(Volume of Conductor*Line Losses*(Maximum Voltage Overhead DC^2)/(4*Resistivity*(Length of Wire DC^2)))
P = sqrt(V*P_loss*(V_m^2)/(4*ρ*(L^2)))

What is the two-wire one conductor earthed system?

The load is connected between the two wires. where a1 is the area of the X-section of the conductor. It is a usual practice to make this system the basis for comparison with other systems.

How to Calculate Transmitted Power using Volume(Two-Wire One Conductor Earthed)?

Transmitted Power using Volume(Two-Wire One Conductor Earthed) calculator uses Power Transmitted = sqrt(Volume of Conductor*Line Losses*(Maximum Voltage Overhead DC^2)/(4*Resistivity*(Length of Wire DC^2))) to calculate the Power Transmitted, The Transmitted Power using Volume(Two-Wire One Conductor Earthed) formula is defined as proportional to its effective range. The higher the transmit power, the farther a signal can travel, and the more obstructions it can effectively penetrate. Power Transmitted is denoted by P symbol.

How to calculate Transmitted Power using Volume(Two-Wire One Conductor Earthed) using this online calculator? To use this online calculator for Transmitted Power using Volume(Two-Wire One Conductor Earthed), enter Volume of Conductor (V), Line Losses (P_loss), Maximum Voltage Overhead DC (V_m), Resistivity (ρ) & Length of Wire DC (L) and hit the calculate button. Here is how the Transmitted Power using Volume(Two-Wire One Conductor Earthed) calculation can be explained with given input values -> 2523.908 = sqrt(26*0.74*(60.26^2)/(4*1.7E-05*(12.7^2))).

FAQ

What is Transmitted Power using Volume(Two-Wire One Conductor Earthed)?

The Transmitted Power using Volume(Two-Wire One Conductor Earthed) formula is defined as proportional to its effective range. The higher the transmit power, the farther a signal can travel, and the more obstructions it can effectively penetrate and is represented as P = sqrt(V*P_loss*(V_m^2)/(4*ρ*(L^2))) or Power Transmitted = sqrt(Volume of Conductor*Line Losses*(Maximum Voltage Overhead DC^2)/(4*Resistivity*(Length of Wire DC^2))). Volume of Conductor is the total volume of the material used to make the conductor of an overhead dc line, Line Losses is defined as the total losses occurring in an Overhead DC line when in use, Maximum Voltage Overhead DC is defined as the peak amplitude of the AC voltage supplied to the line or wire, Resistivity is the measure of how strongly a material opposes the flow of current through them & Length of Wire DC is the total length of the wire from one end to other end.

How to calculate Transmitted Power using Volume(Two-Wire One Conductor Earthed)?

The Transmitted Power using Volume(Two-Wire One Conductor Earthed) formula is defined as proportional to its effective range. The higher the transmit power, the farther a signal can travel, and the more obstructions it can effectively penetrate is calculated using Power Transmitted = sqrt(Volume of Conductor*Line Losses*(Maximum Voltage Overhead DC^2)/(4*Resistivity*(Length of Wire DC^2))). To calculate Transmitted Power using Volume(Two-Wire One Conductor Earthed), you need Volume of Conductor (V), Line Losses (P_loss), Maximum Voltage Overhead DC (V_m), Resistivity (ρ) & Length of Wire DC (L). With our tool, you need to enter the respective value for Volume of Conductor, Line Losses, Maximum Voltage Overhead DC, Resistivity & Length of Wire DC and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Power Transmitted?

In this formula, Power Transmitted uses Volume of Conductor, Line Losses, Maximum Voltage Overhead DC, Resistivity & Length of Wire DC. We can use 3 other way(s) to calculate the same, which is/are as follows -

Power Transmitted = Current Overhead DC*Maximum Voltage Overhead DC
Power Transmitted = sqrt((Line Losses*(Maximum Voltage Overhead DC^2))/(2*Resistance Overhead DC))
Power Transmitted = sqrt(Constant Overhead DC*Line Losses*(Maximum Voltage Overhead DC^2)/(4*Resistivity*(Length of Wire DC^2)))

Home

FREE PDFs

🔍 Search