LCM of two numbers

Transmitted Current-2 using Transmitted Voltage (Line PL) Calculator

Engineering Chemistry Financial Health More >>

↳

Electrical Chemical Engineering Civil Electronics More >>

⤿

Power System Circuit Graph Theory Control System Electrical Circuit More >>

⤿

Transmission Lines Battery Life FACTS Devices Fault More >>

⤿

Transient Line Performance Characteristics Long Transmission Line Medium Line More >>

⤿

Travelling Waves

⤿

Different Cases for Reflection and Transmission Incident Wave Reflected Waves Relation Between Coefficients More >>

⤿

Line With Parallel Loads Line Is Open Circuited Line Is Short Circuited Load IS Open Circuited More >>

⤿

Transmitted Current 1,2 and 3 Impedance 1,2 and 3 Transmitted Coefficient OF Current

✖Transmitted Voltage is defined as the Voltage wave that is traveling through the Load of the Transmission line.ⓘ Transmitted Voltage [V_t]			+10% -10%
✖The Impedance of Secondary Winding is the impedance that is in Secondary winding.ⓘ Impedance of Secondary Winding [Z₂]			+10% -10%

✖Transmitted Current-2 is defined as the current wave that is traveling through the Load-2 of the Transmission line.ⓘ Transmitted Current-2 using Transmitted Voltage (Line PL) [I_t2]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Transmission Lines Formula PDF PDF Image

Transmitted Current-2 using Transmitted Voltage (Line PL) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Transmitted Current-2 = Transmitted Voltage/Impedance of Secondary Winding
I_t2 = V_t/Z₂
This formula uses 3 Variables

Variables Used

Transmitted Current-2 - (Measured in Ampere) - Transmitted Current-2 is defined as the current wave that is traveling through the Load-2 of the Transmission line.
Transmitted Voltage - (Measured in Volt) - Transmitted Voltage is defined as the Voltage wave that is traveling through the Load of the Transmission line.
Impedance of Secondary Winding - (Measured in Ohm) - The Impedance of Secondary Winding is the impedance that is in Secondary winding.

STEP 1: Convert Input(s) to Base Unit

Transmitted Voltage: 20 Volt --> 20 Volt No Conversion Required
Impedance of Secondary Winding: 16 Ohm --> 16 Ohm No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

I_t2 = V_t/Z₂ --> 20/16

Evaluating ... ...

I_t2 = 1.25

STEP 3: Convert Result to Output's Unit

1.25 Ampere --> No Conversion Required

FINAL ANSWER

1.25 Ampere <-- Transmitted Current-2

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Power System » Transmission Lines » Transient » Travelling Waves » Different Cases for Reflection and Transmission » Line With Parallel Loads » Transmitted Current 1,2 and 3 » Transmitted Current-2 using Transmitted Voltage (Line PL)

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Shobhit Dimri

Bipin Tripathi Kumaon Institute of Technology (BTKIT), Dwarahat

Shobhit Dimri has verified this Calculator and 100+ more calculators!

< Transmitted Current 1,2 and 3 Calculators

Transmitted Current-3 using Transmitted Voltage (Line PL)

LaTeX Go Transmitted Current-3 = Transmitted Voltage/Impedance of Tertiary Winding

Transmitted Current-1 (Line PL)

LaTeX Go Transmitted Current-1 = Transmitted Current-2+Transmitted Current-3

Transmitted Current-2 (Line PL)

LaTeX Go Transmitted Current-2 = Transmitted Current-Transmitted Current-3

Transmitted Current-3 (Line PL)

LaTeX Go Transmitted Current-3 = Transmitted Current-Transmitted Current-2

Transmitted Current-2 using Transmitted Voltage (Line PL) Formula

LaTeX Go

Transmitted Current-2 = Transmitted Voltage/Impedance of Secondary Winding
I_t2 = V_t/Z₂

What is line termination?

In electronics, electrical termination is the practice of ending a transmission line with a device that matches the line's characteristic impedance. Termination prevents signals from reflecting off the end of the transmission line.

How to Calculate Transmitted Current-2 using Transmitted Voltage (Line PL)?

Transmitted Current-2 using Transmitted Voltage (Line PL) calculator uses Transmitted Current-2 = Transmitted Voltage/Impedance of Secondary Winding to calculate the Transmitted Current-2, The Transmitted Current-2 using Transmitted Voltage (line PL) formula is defined as the current wave that is traveling through the Load-2 of the Transmission line. Transmitted Current-2 is denoted by I_t2 symbol.

How to calculate Transmitted Current-2 using Transmitted Voltage (Line PL) using this online calculator? To use this online calculator for Transmitted Current-2 using Transmitted Voltage (Line PL), enter Transmitted Voltage (V_t) & Impedance of Secondary Winding (Z₂) and hit the calculate button. Here is how the Transmitted Current-2 using Transmitted Voltage (Line PL) calculation can be explained with given input values -> 1.25 = 20/16.

FAQ

What is Transmitted Current-2 using Transmitted Voltage (Line PL)?

The Transmitted Current-2 using Transmitted Voltage (line PL) formula is defined as the current wave that is traveling through the Load-2 of the Transmission line and is represented as I_t2 = V_t/Z₂ or Transmitted Current-2 = Transmitted Voltage/Impedance of Secondary Winding. Transmitted Voltage is defined as the Voltage wave that is traveling through the Load of the Transmission line & The Impedance of Secondary Winding is the impedance that is in Secondary winding.

How to calculate Transmitted Current-2 using Transmitted Voltage (Line PL)?

The Transmitted Current-2 using Transmitted Voltage (line PL) formula is defined as the current wave that is traveling through the Load-2 of the Transmission line is calculated using Transmitted Current-2 = Transmitted Voltage/Impedance of Secondary Winding. To calculate Transmitted Current-2 using Transmitted Voltage (Line PL), you need Transmitted Voltage (V_t) & Impedance of Secondary Winding (Z₂). With our tool, you need to enter the respective value for Transmitted Voltage & Impedance of Secondary Winding and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Transmitted Current-2?

In this formula, Transmitted Current-2 uses Transmitted Voltage & Impedance of Secondary Winding. We can use 1 other way(s) to calculate the same, which is/are as follows -

Transmitted Current-2 = Transmitted Current-Transmitted Current-3

Home

FREE PDFs

🔍 Search