HCF of two numbers

Transmitted Voltage using Transmitted Current-3 (Line PL) Calculator

Engineering Chemistry Financial Health More >>

↳

Electrical Chemical Engineering Civil Electronics More >>

⤿

Power System Circuit Graph Theory Control System Electrical Circuit More >>

⤿

Transmission Lines Battery Life FACTS Devices Fault More >>

⤿

Transient Line Performance Characteristics Long Transmission Line Medium Line More >>

⤿

Travelling Waves

⤿

Different Cases for Reflection and Transmission Incident Wave Reflected Waves Relation Between Coefficients More >>

⤿

Line With Parallel Loads Line Is Open Circuited Line Is Short Circuited Load IS Open Circuited More >>

⤿

Impedance 1,2 and 3 Transmitted Coefficient OF Current Transmitted Current 1,2 and 3

✖Transmitted Current is defined as the Current wave that is traveling through the Load of the Transmission line.ⓘ Transmitted Current [I_t]			+10% -10%
✖Impedance of Tertiary Winding in electrical devices, refers to the amount of opposition faced by the direct or alternating current when it passes through a conductor component, circuit, or system.ⓘ Impedance of Tertiary Winding [Z₃]			+10% -10%

✖Transmitted Voltage is defined as the Voltage wave that is traveling through the Load of the Transmission line.ⓘ Transmitted Voltage using Transmitted Current-3 (Line PL) [V_t]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Transmission Lines Formula PDF PDF Image

Transmitted Voltage using Transmitted Current-3 (Line PL) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Transmitted Voltage = Transmitted Current*Impedance of Tertiary Winding
V_t = I_t*Z₃
This formula uses 3 Variables

Variables Used

Transmitted Voltage - (Measured in Volt) - Transmitted Voltage is defined as the Voltage wave that is traveling through the Load of the Transmission line.
Transmitted Current - (Measured in Ampere) - Transmitted Current is defined as the Current wave that is traveling through the Load of the Transmission line.
Impedance of Tertiary Winding - (Measured in Ohm) - Impedance of Tertiary Winding in electrical devices, refers to the amount of opposition faced by the direct or alternating current when it passes through a conductor component, circuit, or system.

STEP 1: Convert Input(s) to Base Unit

Transmitted Current: 4.8 Ampere --> 4.8 Ampere No Conversion Required
Impedance of Tertiary Winding: 22 Ohm --> 22 Ohm No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

V_t = I_t*Z₃ --> 4.8*22

Evaluating ... ...

V_t = 105.6

STEP 3: Convert Result to Output's Unit

105.6 Volt --> No Conversion Required

FINAL ANSWER

105.6 Volt <-- Transmitted Voltage

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Power System » Transmission Lines » Transient » Travelling Waves » Different Cases for Reflection and Transmission » Line With Parallel Loads » Transmitted Voltage using Transmitted Current-3 (Line PL)

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Kethavath Srinath

Osmania University (OU), Hyderabad

Kethavath Srinath has verified this Calculator and 1200+ more calculators!

< Line With Parallel Loads Calculators

Reflected Current using Transmitted Current-3 and 2 (Line PL)

LaTeX Go Reflected Current = Incident Current-Transmitted Current-Transmitted Current

Incident Current using Transmitted Current-3 and 2 (Line PL)

LaTeX Go Incident Current = Reflected Current-Transmitted Current-Transmitted Current

Transmitted Voltage using Transmitted Current-2 (Line PL)

LaTeX Go Transmitted Voltage = Transmitted Current*Impedance of Secondary Winding

Transmitted Voltage using Transmitted Current-3 (Line PL)

LaTeX Go Transmitted Voltage = Transmitted Current*Impedance of Tertiary Winding

Transmitted Voltage using Transmitted Current-3 (Line PL) Formula

LaTeX Go

Transmitted Voltage = Transmitted Current*Impedance of Tertiary Winding
V_t = I_t*Z₃

What is line termination?

In electronics, electrical termination is the practice of ending a transmission line with a device that matches the line's characteristic impedance. Termination prevents signals from reflecting off the end of the transmission line.

How to Calculate Transmitted Voltage using Transmitted Current-3 (Line PL)?

Transmitted Voltage using Transmitted Current-3 (Line PL) calculator uses Transmitted Voltage = Transmitted Current*Impedance of Tertiary Winding to calculate the Transmitted Voltage, The Transmitted Voltage using Transmitted Current-3 (line PL) formula is defined as the current wave that is traveling through the Load of the Transmission line. Transmitted Voltage is denoted by V_t symbol.

How to calculate Transmitted Voltage using Transmitted Current-3 (Line PL) using this online calculator? To use this online calculator for Transmitted Voltage using Transmitted Current-3 (Line PL), enter Transmitted Current (I_t) & Impedance of Tertiary Winding (Z₃) and hit the calculate button. Here is how the Transmitted Voltage using Transmitted Current-3 (Line PL) calculation can be explained with given input values -> 105.6 = 4.8*22.

FAQ

What is Transmitted Voltage using Transmitted Current-3 (Line PL)?

The Transmitted Voltage using Transmitted Current-3 (line PL) formula is defined as the current wave that is traveling through the Load of the Transmission line and is represented as V_t = I_t*Z₃ or Transmitted Voltage = Transmitted Current*Impedance of Tertiary Winding. Transmitted Current is defined as the Current wave that is traveling through the Load of the Transmission line & Impedance of Tertiary Winding in electrical devices, refers to the amount of opposition faced by the direct or alternating current when it passes through a conductor component, circuit, or system.

How to calculate Transmitted Voltage using Transmitted Current-3 (Line PL)?

The Transmitted Voltage using Transmitted Current-3 (line PL) formula is defined as the current wave that is traveling through the Load of the Transmission line is calculated using Transmitted Voltage = Transmitted Current*Impedance of Tertiary Winding. To calculate Transmitted Voltage using Transmitted Current-3 (Line PL), you need Transmitted Current (I_t) & Impedance of Tertiary Winding (Z₃). With our tool, you need to enter the respective value for Transmitted Current & Impedance of Tertiary Winding and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Transmitted Voltage?

In this formula, Transmitted Voltage uses Transmitted Current & Impedance of Tertiary Winding. We can use 3 other way(s) to calculate the same, which is/are as follows -

Transmitted Voltage = Transmitted Current*Impedance of Secondary Winding
Transmitted Voltage = (2*Incident Voltage)/(Impedance of Primary Winding*((1/Impedance of Primary Winding)+(1/Impedance of Secondary Winding)+(1/Impedance of Tertiary Winding)))
Transmitted Voltage = Transmission Coefficient of Current*Incident Voltage*Impedance of Secondary Winding/(Impedance of Primary Winding)

Home

FREE PDFs

🔍 Search