Thickness of plates given strength of joint per pitch length (triple rivet) Calculator

✖Strength of joint is the strength of riveted joint per pitch length.ⓘ Strength of Joint [S]			+10% -10%
✖Crushing stress is a special type of localized compressive stress which occurs at the surface of contact of two members that are relatively at rest.ⓘ Crushing Stress [σ_c]			+10% -10%
✖Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.ⓘ Rivet Diameter [D_rivet]			+10% -10%

✖The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.ⓘ Thickness of plates given strength of joint per pitch length (triple rivet) [t_plate]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Strength of Materials Formula PDF PDF Image

Thickness of plates given strength of joint per pitch length (triple rivet) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Thickness of Plate = Strength of Joint/(3*Crushing Stress*Rivet Diameter)
t_plate = S/(3*σ_c*D_rivet)
This formula uses 4 Variables

Variables Used

Thickness of Plate - (Measured in Meter) - The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.
Strength of Joint - (Measured in Newton) - Strength of joint is the strength of riveted joint per pitch length.
Crushing Stress - (Measured in Pascal) - Crushing stress is a special type of localized compressive stress which occurs at the surface of contact of two members that are relatively at rest.
Rivet Diameter - (Measured in Meter) - Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.

STEP 1: Convert Input(s) to Base Unit

Strength of Joint: 8.6 Kilonewton --> 8600 Newton (Check conversion here)
Crushing Stress: 20.83333 Megapascal --> 20833330 Pascal (Check conversion here)
Rivet Diameter: 18 Millimeter --> 0.018 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

t_plate = S/(3*σ_c*D_rivet) --> 8600/(3*20833330*0.018)

Evaluating ... ...

t_plate = 0.00764444566755575

STEP 3: Convert Result to Output's Unit

0.00764444566755575 Meter -->7.64444566755575 Millimeter (Check conversion here)

FINAL ANSWER

7.64444566755575 ≈ 7.644446 Millimeter <-- Thickness of Plate

(Calculation completed in 00.020 seconds)

You are here -

Home » Physics » Strength of Materials » Riveted Joint » Failure of A Riveted Joint » Mechanical » Failure Due to Crushing of Rivet or Plate » Thickness of plates given strength of joint per pitch length (triple rivet)

Credits

Created by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has created this Calculator and 2000+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< Failure Due to Crushing of Rivet or Plate Calculators

Safe load which rivet can withstand against crushing

LaTeX Go Safe Load Joint = Crushing Stress*Rivet Diameter*Thickness of Plate

Allowable crushing stress given safe load which rivet can withstand for given projected area

LaTeX Go Crushing Stress = Safe Load Joint/(Projected Area)

Projected area given safe load which rivet can withstand against crushing

LaTeX Go Projected Area = Safe Load Joint/(Crushing Stress)

Safe load which rivet can withstand against crushing given projected area

LaTeX Go Safe Load Joint = Crushing Stress*Projected Area

Thickness of plates given strength of joint per pitch length (triple rivet) Formula

LaTeX Go

Thickness of Plate = Strength of Joint/(3*Crushing Stress*Rivet Diameter)
t_plate = S/(3*σ_c*D_rivet)

What is tear and tensile strength?

Tear strength is the measure of how much tensile stress the material can withstand in a specific case, i.e. when a tear has been introduced in the material, whereas a normal tensile stress test is done for a non-defective piece of material.

How to Calculate Thickness of plates given strength of joint per pitch length (triple rivet)?

Thickness of plates given strength of joint per pitch length (triple rivet) calculator uses Thickness of Plate = Strength of Joint/(3*Crushing Stress*Rivet Diameter) to calculate the Thickness of Plate, The Thickness of plates given strength of joint per pitch length (triple rivet) formula is defined as the thickness of the thickest sheet that is being joined. Thickness of Plate is denoted by t_plate symbol.

How to calculate Thickness of plates given strength of joint per pitch length (triple rivet) using this online calculator? To use this online calculator for Thickness of plates given strength of joint per pitch length (triple rivet), enter Strength of Joint (S), Crushing Stress (σ_c) & Rivet Diameter (D_rivet) and hit the calculate button. Here is how the Thickness of plates given strength of joint per pitch length (triple rivet) calculation can be explained with given input values -> 66358.02 = 8600/(3*20833330*0.018).

FAQ

What is Thickness of plates given strength of joint per pitch length (triple rivet)?

The Thickness of plates given strength of joint per pitch length (triple rivet) formula is defined as the thickness of the thickest sheet that is being joined and is represented as t_plate = S/(3*σ_c*D_rivet) or Thickness of Plate = Strength of Joint/(3*Crushing Stress*Rivet Diameter). Strength of joint is the strength of riveted joint per pitch length, Crushing stress is a special type of localized compressive stress which occurs at the surface of contact of two members that are relatively at rest & Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.

How to calculate Thickness of plates given strength of joint per pitch length (triple rivet)?

The Thickness of plates given strength of joint per pitch length (triple rivet) formula is defined as the thickness of the thickest sheet that is being joined is calculated using Thickness of Plate = Strength of Joint/(3*Crushing Stress*Rivet Diameter). To calculate Thickness of plates given strength of joint per pitch length (triple rivet), you need Strength of Joint (S), Crushing Stress (σ_c) & Rivet Diameter (D_rivet). With our tool, you need to enter the respective value for Strength of Joint, Crushing Stress & Rivet Diameter and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Thickness of Plate?

In this formula, Thickness of Plate uses Strength of Joint, Crushing Stress & Rivet Diameter. We can use 3 other way(s) to calculate the same, which is/are as follows -

Thickness of Plate = Safe Load Joint/(Crushing Stress*Rivet Diameter)
Thickness of Plate = Strength of Joint/(1*Crushing Stress*Rivet Diameter)
Thickness of Plate = Strength of Joint/(2*Crushing Stress*Rivet Diameter)

Home

FREE PDFs

🔍 Search