Thickness of Fluid between Members given Shape Factor Calculator

✖Outside Diameter of Packing Gasket is the diameter of the external periphery of a gasket used in packing and sealing operations.ⓘ Outside Diameter of Packing Gasket [D_o]			+10% -10%
✖Inside Diameter of Packing Gasket is the diameter of the internal periphery of a gasket used in packing and sealing operations.ⓘ Inside Diameter of Packing Gasket [D_i]			+10% -10%
✖Shape Factor For Circular Gasket is the ratio of the area of one load face to the area free to bulge.ⓘ Shape Factor For Circular Gasket [S_pf]			+10% -10%

✖Thickness of Fluid Between Members refers to how resistant a fluid is to moving through it. For example, Water has a low or "thin" viscosity, while honey has a "thick" or high viscosity.ⓘ Thickness of Fluid between Members given Shape Factor [t]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Seals Formulas PDF PDF Image

Thickness of Fluid between Members given Shape Factor Solution

STEP 0: Pre-Calculation Summary

Formula Used

Thickness of Fluid Between Members = (Outside Diameter of Packing Gasket-Inside Diameter of Packing Gasket)/(4*Shape Factor For Circular Gasket)
t = (D_o-D_i)/(4*S_pf)
This formula uses 4 Variables

Variables Used

Thickness of Fluid Between Members - (Measured in Meter) - Thickness of Fluid Between Members refers to how resistant a fluid is to moving through it. For example, Water has a low or "thin" viscosity, while honey has a "thick" or high viscosity.
Outside Diameter of Packing Gasket - (Measured in Meter) - Outside Diameter of Packing Gasket is the diameter of the external periphery of a gasket used in packing and sealing operations.
Inside Diameter of Packing Gasket - (Measured in Meter) - Inside Diameter of Packing Gasket is the diameter of the internal periphery of a gasket used in packing and sealing operations.
Shape Factor For Circular Gasket - Shape Factor For Circular Gasket is the ratio of the area of one load face to the area free to bulge.

STEP 1: Convert Input(s) to Base Unit

Outside Diameter of Packing Gasket: 60 Millimeter --> 0.06 Meter (Check conversion here)
Inside Diameter of Packing Gasket: 54 Millimeter --> 0.054 Meter (Check conversion here)
Shape Factor For Circular Gasket: 0.78 --> No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

t = (D_o-D_i)/(4*S_pf) --> (0.06-0.054)/(4*0.78)

Evaluating ... ...

t = 0.00192307692307692

STEP 3: Convert Result to Output's Unit

0.00192307692307692 Meter -->1.92307692307692 Millimeter (Check conversion here)

FINAL ANSWER

1.92307692307692 ≈ 1.923077 Millimeter <-- Thickness of Fluid Between Members

(Calculation completed in 00.004 seconds)

You are here -

Home » Physics » Design of Machine Elements » Design of Coupling » Seals » Mechanical » Leakage through Bush Seals » Thickness of Fluid between Members given Shape Factor

Credits

Created by sanjay shiva

national institute of technology hamirpur (NITH ), hamirpur , himachal pradesh

sanjay shiva has created this Calculator and 100+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Leakage through Bush Seals Calculators

Volumetric Flow Rate under Laminar Flow Condition for Radial Bush Seal for Incompressible Fluid

LaTeX Go Volumetric Flow Rate Per Unit Pressure = (Radial Clearance For Seals^3)/(12*Absolute Viscosity of Oil in Seals)*(Outer Radius of Plain Bush Seal-Inner Radius of Plain Bush Seal)/(Outer Radius of Plain Bush Seal*ln(Outer Radius of Plain Bush Seal/Inner Radius of Plain Bush Seal))

Oil Flow through Plain Radial Bush Seal due to Leakage under Laminar Flow Condition

LaTeX Go Oil Flow From Bush Seal = (2*pi*Outer Radius of Plain Bush Seal*(Minimum Percentage Compression-Exit Pressure/10^6))/(Outer Radius of Plain Bush Seal-Inner Radius of Plain Bush Seal)*Volumetric Flow Rate Per Unit Pressure

Oil Flow through Plain Axial Bush Seal due to Leakage under Laminar Flow Condition

LaTeX Go Oil Flow From Bush Seal = (2*pi*Outer Radius of Plain Bush Seal*(Minimum Percentage Compression-Exit Pressure/10^6))/(Depth of U Collar)*Volumetric Flow Rate Per Unit Pressure

Volumetric Flow Rate under Laminar Flow Condition for Axial Bush Seal for Compressible Fluid

LaTeX Go Volumetric Flow Rate Per Unit Pressure = (Radial Clearance For Seals^3)/(12*Absolute Viscosity of Oil in Seals)*(Minimum Percentage Compression+Exit Pressure)/(Exit Pressure)

Thickness of Fluid between Members given Shape Factor Formula

LaTeX Go

Thickness of Fluid Between Members = (Outside Diameter of Packing Gasket-Inside Diameter of Packing Gasket)/(4*Shape Factor For Circular Gasket)
t = (D_o-D_i)/(4*S_pf)

What is gasket?

Gasket is a shaped sheet or ring of rubber or other material sealing the junction between two surfaces in an engine or other device.

How to Calculate Thickness of Fluid between Members given Shape Factor?

Thickness of Fluid between Members given Shape Factor calculator uses Thickness of Fluid Between Members = (Outside Diameter of Packing Gasket-Inside Diameter of Packing Gasket)/(4*Shape Factor For Circular Gasket) to calculate the Thickness of Fluid Between Members, The Thickness of Fluid between Members given Shape Factor formula is defined as how resistant a fluid is to move through it. Thickness of Fluid Between Members is denoted by t symbol.

How to calculate Thickness of Fluid between Members given Shape Factor using this online calculator? To use this online calculator for Thickness of Fluid between Members given Shape Factor, enter Outside Diameter of Packing Gasket (D_o), Inside Diameter of Packing Gasket (D_i) & Shape Factor For Circular Gasket (S_pf) and hit the calculate button. Here is how the Thickness of Fluid between Members given Shape Factor calculation can be explained with given input values -> 1923.077 = (0.06-0.054)/(4*0.78).

FAQ

What is Thickness of Fluid between Members given Shape Factor?

The Thickness of Fluid between Members given Shape Factor formula is defined as how resistant a fluid is to move through it and is represented as t = (D_o-D_i)/(4*S_pf) or Thickness of Fluid Between Members = (Outside Diameter of Packing Gasket-Inside Diameter of Packing Gasket)/(4*Shape Factor For Circular Gasket). Outside Diameter of Packing Gasket is the diameter of the external periphery of a gasket used in packing and sealing operations, Inside Diameter of Packing Gasket is the diameter of the internal periphery of a gasket used in packing and sealing operations & Shape Factor For Circular Gasket is the ratio of the area of one load face to the area free to bulge.

How to calculate Thickness of Fluid between Members given Shape Factor?

The Thickness of Fluid between Members given Shape Factor formula is defined as how resistant a fluid is to move through it is calculated using Thickness of Fluid Between Members = (Outside Diameter of Packing Gasket-Inside Diameter of Packing Gasket)/(4*Shape Factor For Circular Gasket). To calculate Thickness of Fluid between Members given Shape Factor, you need Outside Diameter of Packing Gasket (D_o), Inside Diameter of Packing Gasket (D_i) & Shape Factor For Circular Gasket (S_pf). With our tool, you need to enter the respective value for Outside Diameter of Packing Gasket, Inside Diameter of Packing Gasket & Shape Factor For Circular Gasket and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Thickness of Fluid Between Members?

In this formula, Thickness of Fluid Between Members uses Outside Diameter of Packing Gasket, Inside Diameter of Packing Gasket & Shape Factor For Circular Gasket. We can use 1 other way(s) to calculate the same, which is/are as follows -

Thickness of Fluid Between Members = (pi*Kinematic Viscosity of Bush Seal Fluid*Nominal Packing Cross Section of Bush Seal^2)/(13200*Power Loss For Seal)*(Outer Radius of Rotating Member Inside Bush Seal^4-Inner Radius of Rotating Member Inside Bush Seal^4)

Home

FREE PDFs

🔍 Search