Thickness of Plates given Load Carried by Parallel Fillet Weld Calculator

✖Load on weld is the instantaneous load applied perpendicular to the specimen cross section.ⓘ Load on weld [W]			+10% -10%
✖Shear Stress is force tending to cause deformation of a material by slippage along a plane or planes parallel to the imposed stress.ⓘ Shear Stress [𝜏]			+10% -10%
✖Length of Parallel Fillet Weld is the distance between two consecutive end of welds.ⓘ Length of Parallel Fillet Weld [L_parallel]			+10% -10%

✖The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.ⓘ Thickness of Plates given Load Carried by Parallel Fillet Weld [t_plate]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Strength of Materials Formula PDF PDF Image

Thickness of Plates given Load Carried by Parallel Fillet Weld Solution

STEP 0: Pre-Calculation Summary

Formula Used

Thickness of Plate = Load on weld/(1.414*Shear Stress*Length of Parallel Fillet Weld)
t_plate = W/(1.414*𝜏*L_parallel)
This formula uses 4 Variables

Variables Used

Thickness of Plate - (Measured in Meter) - The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.
Load on weld - (Measured in Newton) - Load on weld is the instantaneous load applied perpendicular to the specimen cross section.
Shear Stress - (Measured in Pascal) - Shear Stress is force tending to cause deformation of a material by slippage along a plane or planes parallel to the imposed stress.
Length of Parallel Fillet Weld - (Measured in Meter) - Length of Parallel Fillet Weld is the distance between two consecutive end of welds.

STEP 1: Convert Input(s) to Base Unit

Load on weld: 9 Kilonewton --> 9000 Newton (Check conversion here)
Shear Stress: 2.4 Megapascal --> 2400000 Pascal (Check conversion here)
Length of Parallel Fillet Weld: 200 Millimeter --> 0.2 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

t_plate = W/(1.414*𝜏*L_parallel) --> 9000/(1.414*2400000*0.2)

Evaluating ... ...

t_plate = 0.0132602545968883

STEP 3: Convert Result to Output's Unit

0.0132602545968883 Meter -->13.2602545968883 Millimeter (Check conversion here)

FINAL ANSWER

13.2602545968883 ≈ 13.26025 Millimeter <-- Thickness of Plate

(Calculation completed in 00.020 seconds)

You are here -

Home » Physics » Strength of Materials » Welded Joints » Mechanical » Analysis of Compound Weld » Thickness of Plates given Load Carried by Parallel Fillet Weld

Credits

Created by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has created this Calculator and 2000+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< Analysis of Compound Weld Calculators

Length of Single Fillet Lap Weld given Load Carried by Single Fillet Lap Weld

LaTeX Go Length of Single Fillet Lap Weld = Load on weld/(0.707*Tensile Stress*Thickness of Plate)

Allowable Tensile Stress given Load Carried by Single Fillet Lap Weld

LaTeX Go Tensile Stress = Load on weld/(0.707*Length of Single Fillet Lap Weld*Thickness of Plate)

Thickness of Plates given Load Carried by Single Fillet Lap Weld

LaTeX Go Thickness of Plate = Load on weld/(0.707*Tensile Stress*Length of Single Fillet Lap Weld)

Load Carried by Single Fillet Lap Weld

LaTeX Go Load on weld = 0.707*Tensile Stress*Length of Single Fillet Lap Weld*Thickness of Plate

Thickness of Plates given Load Carried by Parallel Fillet Weld Formula

LaTeX Go

Thickness of Plate = Load on weld/(1.414*Shear Stress*Length of Parallel Fillet Weld)
t_plate = W/(1.414*𝜏*L_parallel)

What do you mean by maximum shear stress theory?

The maximum shear stress theory states that the failure or yielding of a ductile material will occur when the maximum shear stress of the material equals or exceeds the shear stress value at the yield point in the uniaxial tensile test.

How to Calculate Thickness of Plates given Load Carried by Parallel Fillet Weld?

Thickness of Plates given Load Carried by Parallel Fillet Weld calculator uses Thickness of Plate = Load on weld/(1.414*Shear Stress*Length of Parallel Fillet Weld) to calculate the Thickness of Plate, Thickness of plates given load carried by parallel fillet weld is defined as the distance through the plate, as distinct from width or height. Thickness of Plate is denoted by t_plate symbol.

How to calculate Thickness of Plates given Load Carried by Parallel Fillet Weld using this online calculator? To use this online calculator for Thickness of Plates given Load Carried by Parallel Fillet Weld, enter Load on weld (W), Shear Stress (𝜏) & Length of Parallel Fillet Weld (L_parallel) and hit the calculate button. Here is how the Thickness of Plates given Load Carried by Parallel Fillet Weld calculation can be explained with given input values -> 5304.102 = 9000/(1.414*2400000*0.2).

FAQ

What is Thickness of Plates given Load Carried by Parallel Fillet Weld?

Thickness of plates given load carried by parallel fillet weld is defined as the distance through the plate, as distinct from width or height and is represented as t_plate = W/(1.414*𝜏*L_parallel) or Thickness of Plate = Load on weld/(1.414*Shear Stress*Length of Parallel Fillet Weld). Load on weld is the instantaneous load applied perpendicular to the specimen cross section, Shear Stress is force tending to cause deformation of a material by slippage along a plane or planes parallel to the imposed stress & Length of Parallel Fillet Weld is the distance between two consecutive end of welds.

How to calculate Thickness of Plates given Load Carried by Parallel Fillet Weld?

Thickness of plates given load carried by parallel fillet weld is defined as the distance through the plate, as distinct from width or height is calculated using Thickness of Plate = Load on weld/(1.414*Shear Stress*Length of Parallel Fillet Weld). To calculate Thickness of Plates given Load Carried by Parallel Fillet Weld, you need Load on weld (W), Shear Stress (𝜏) & Length of Parallel Fillet Weld (L_parallel). With our tool, you need to enter the respective value for Load on weld, Shear Stress & Length of Parallel Fillet Weld and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Thickness of Plate?

In this formula, Thickness of Plate uses Load on weld, Shear Stress & Length of Parallel Fillet Weld. We can use 2 other way(s) to calculate the same, which is/are as follows -

Thickness of Plate = Load on weld/(0.707*Tensile Stress*Length of Single Fillet Lap Weld)
Thickness of Plate = Load on weld/(1.414*Shear Stress*Length of Parallel Fillet Weld+0.707*Tensile Stress*Length of Single Fillet Lap Weld)

Home

FREE PDFs

🔍 Search