Thickness of plate given tearing strength of rivet Calculator

✖Tearing strength is defined as the force required to start or to continue to tear a fabric, in either weft or warp direction, under specified conditions.ⓘ Tearing Strength [T_strength]			+10% -10%
✖Tensile stress can be defined as the magnitude of force applied along an elastic rod, which is divided by the cross-sectional area of the rod in a direction perpendicular to the applied force.ⓘ Tensile Stress [σ_t]			+10% -10%
✖Pitch of Rivet is defined as the distance between the centers of adjacent rivets that hold together the parts of a built member.ⓘ Pitch of Rivet [p]			+10% -10%
✖Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.ⓘ Rivet Diameter [D_rivet]			+10% -10%

✖The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.ⓘ Thickness of plate given tearing strength of rivet [t_plate]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Strength of Materials Formula PDF PDF Image

Thickness of plate given tearing strength of rivet Solution

STEP 0: Pre-Calculation Summary

Formula Used

Thickness of Plate = Tearing Strength/(Tensile Stress*(Pitch of Rivet-Rivet Diameter))
t_plate = T_strength/(σ_t*(p-D_rivet))
This formula uses 5 Variables

Variables Used

Thickness of Plate - (Measured in Meter) - The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.
Tearing Strength - (Measured in Newton) - Tearing strength is defined as the force required to start or to continue to tear a fabric, in either weft or warp direction, under specified conditions.
Tensile Stress - (Measured in Pascal) - Tensile stress can be defined as the magnitude of force applied along an elastic rod, which is divided by the cross-sectional area of the rod in a direction perpendicular to the applied force.
Pitch of Rivet - (Measured in Meter) - Pitch of Rivet is defined as the distance between the centers of adjacent rivets that hold together the parts of a built member.
Rivet Diameter - (Measured in Meter) - Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.

STEP 1: Convert Input(s) to Base Unit

Tearing Strength: 4 Kilonewton --> 4000 Newton (Check conversion here)
Tensile Stress: 0.173 Megapascal --> 173000 Pascal (Check conversion here)
Pitch of Rivet: 20 Millimeter --> 0.02 Meter (Check conversion here)
Rivet Diameter: 18 Millimeter --> 0.018 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

t_plate = T_strength/(σ_t*(p-D_rivet)) --> 4000/(173000*(0.02-0.018))

Evaluating ... ...

t_plate = 11.5606936416185

STEP 3: Convert Result to Output's Unit

11.5606936416185 Meter -->11560.6936416185 Millimeter (Check conversion here)

FINAL ANSWER

11560.6936416185 ≈ 11560.69 Millimeter <-- Thickness of Plate

(Calculation completed in 00.004 seconds)

You are here -

Home » Physics » Strength of Materials » Riveted Joint » Strength of a Riveted Joint » Mechanical » Thickness of Plate » Thickness of plate given tearing strength of rivet

Credits

Created by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has created this Calculator and 2000+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< Thickness of Plate Calculators

Thickness of plate given efficiency of riveted joint

LaTeX Go Thickness of Plate = Least Value of Strength/(Tensile Stress*Pitch of Rivet*Efficiency of Riveted Joint)

Thickness of plate given tearing strength of rivet

LaTeX Go Thickness of Plate = Tearing Strength/(Tensile Stress*(Pitch of Rivet-Rivet Diameter))

Thickness of plate given strength of solid plate per pitch length

LaTeX Go Thickness of Plate = Strength of Solid Plate/(Tensile Stress*Pitch of Rivet)

Thickness of plates given crushing strength for double rivet

LaTeX Go Thickness of Plate = Crushing strength/(2*Crushing Stress*Rivet Diameter)

Thickness of plate given tearing strength of rivet Formula

LaTeX Go

Thickness of Plate = Tearing Strength/(Tensile Stress*(Pitch of Rivet-Rivet Diameter))
t_plate = T_strength/(σ_t*(p-D_rivet))

What is tear and tensile strength?

Tear strength is the measure of how much tensile stress the material can withstand in a specific case, i.e. when a tear has been introduced in the material, whereas a normal tensile stress test is done for a non-defective piece of material.

How to Calculate Thickness of plate given tearing strength of rivet?

Thickness of plate given tearing strength of rivet calculator uses Thickness of Plate = Tearing Strength/(Tensile Stress*(Pitch of Rivet-Rivet Diameter)) to calculate the Thickness of Plate, The Thickness of plate given tearing strength of rivet formula is defined as the thickness of the thickest sheet that is being joined. Thickness of Plate is denoted by t_plate symbol.

How to calculate Thickness of plate given tearing strength of rivet using this online calculator? To use this online calculator for Thickness of plate given tearing strength of rivet, enter Tearing Strength (T_strength), Tensile Stress (σ_t), Pitch of Rivet (p) & Rivet Diameter (D_rivet) and hit the calculate button. Here is how the Thickness of plate given tearing strength of rivet calculation can be explained with given input values -> 1.2E+7 = 4000/(173000*(0.02-0.018)).

FAQ

What is Thickness of plate given tearing strength of rivet?

The Thickness of plate given tearing strength of rivet formula is defined as the thickness of the thickest sheet that is being joined and is represented as t_plate = T_strength/(σ_t*(p-D_rivet)) or Thickness of Plate = Tearing Strength/(Tensile Stress*(Pitch of Rivet-Rivet Diameter)). Tearing strength is defined as the force required to start or to continue to tear a fabric, in either weft or warp direction, under specified conditions, Tensile stress can be defined as the magnitude of force applied along an elastic rod, which is divided by the cross-sectional area of the rod in a direction perpendicular to the applied force, Pitch of Rivet is defined as the distance between the centers of adjacent rivets that hold together the parts of a built member & Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.

How to calculate Thickness of plate given tearing strength of rivet?

The Thickness of plate given tearing strength of rivet formula is defined as the thickness of the thickest sheet that is being joined is calculated using Thickness of Plate = Tearing Strength/(Tensile Stress*(Pitch of Rivet-Rivet Diameter)). To calculate Thickness of plate given tearing strength of rivet, you need Tearing Strength (T_strength), Tensile Stress (σ_t), Pitch of Rivet (p) & Rivet Diameter (D_rivet). With our tool, you need to enter the respective value for Tearing Strength, Tensile Stress, Pitch of Rivet & Rivet Diameter and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Thickness of Plate?

In this formula, Thickness of Plate uses Tearing Strength, Tensile Stress, Pitch of Rivet & Rivet Diameter. We can use 3 other way(s) to calculate the same, which is/are as follows -

Thickness of Plate = Least Value of Strength/(Tensile Stress*Pitch of Rivet*Efficiency of Riveted Joint)
Thickness of Plate = Strength of Solid Plate/(Tensile Stress*Pitch of Rivet)
Thickness of Plate = Crushing strength/(2*Crushing Stress*Rivet Diameter)

Home

FREE PDFs

🔍 Search