Thickness of Jacket Shell for Internal Pressure Calculator

✖Design Jacket Pressure refers to a type of pressure vessel designed to withstand high pressures and temperatures, typically used for containing gases or liquids under extreme conditions.ⓘ Design Jacket Pressure [p_j]			+10% -10%
✖Internal Diameter of Shell is a measurement of the distance of a straight line from one point on the inner wall of the object, through its center, to an opposite point also on the inside.ⓘ Internal Diameter of Shell [D_i]			+10% -10%
✖Allowable Stress for Jacket Material at Design Temperature is defined as the material failure stress divided by a factor of safety greater than one.ⓘ Allowable Stress for Jacket Material [f_j]			+10% -10%
✖Joint Efficiency for Shell refers to the effectiveness of the joint between two adjacent sections of a cylindrical shell, such as in a pressure vessel or a storage tank.ⓘ Joint Efficiency for Shell [J]			+10% -10%

✖Required Thickness of Jacket refers to the thickness of the outer shell of a vessel that surrounds the main vessel and is used to provide heating or cooling to the contents of the vessel.ⓘ Thickness of Jacket Shell for Internal Pressure [t_rj]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Jacketed Reaction Vessel Formulas PDF PDF Image

Thickness of Jacket Shell for Internal Pressure Solution

STEP 0: Pre-Calculation Summary

Formula Used

Required Thickness of Jacket = (Design Jacket Pressure*Internal Diameter of Shell)/((2*Allowable Stress for Jacket Material*Joint Efficiency for Shell)-Design Jacket Pressure)
t_rj = (p_j*D_i)/((2*f_j*J)-p_j)
This formula uses 5 Variables

Variables Used

Required Thickness of Jacket - (Measured in Millimeter) - Required Thickness of Jacket refers to the thickness of the outer shell of a vessel that surrounds the main vessel and is used to provide heating or cooling to the contents of the vessel.
Design Jacket Pressure - (Measured in Newton per Square Millimeter) - Design Jacket Pressure refers to a type of pressure vessel designed to withstand high pressures and temperatures, typically used for containing gases or liquids under extreme conditions.
Internal Diameter of Shell - (Measured in Millimeter) - Internal Diameter of Shell is a measurement of the distance of a straight line from one point on the inner wall of the object, through its center, to an opposite point also on the inside.
Allowable Stress for Jacket Material - (Measured in Newton per Square Millimeter) - Allowable Stress for Jacket Material at Design Temperature is defined as the material failure stress divided by a factor of safety greater than one.
Joint Efficiency for Shell - Joint Efficiency for Shell refers to the effectiveness of the joint between two adjacent sections of a cylindrical shell, such as in a pressure vessel or a storage tank.

STEP 1: Convert Input(s) to Base Unit

Design Jacket Pressure: 0.105 Newton per Square Millimeter --> 0.105 Newton per Square Millimeter No Conversion Required
Internal Diameter of Shell: 1500 Millimeter --> 1500 Millimeter No Conversion Required
Allowable Stress for Jacket Material: 120 Newton per Square Millimeter --> 120 Newton per Square Millimeter No Conversion Required
Joint Efficiency for Shell: 0.85 --> No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

t_rj = (p_j*D_i)/((2*f_j*J)-p_j) --> (0.105*1500)/((2*120*0.85)-0.105)

Evaluating ... ...

t_rj = 0.772456411388215

STEP 3: Convert Result to Output's Unit

0.000772456411388215 Meter -->0.772456411388215 Millimeter (Check conversion here)

FINAL ANSWER

0.772456411388215 ≈ 0.772456 Millimeter <-- Required Thickness of Jacket

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Chemical Engineering » Process Equipment Design » Jacketed Reaction Vessel » Thickness of Jacket Shell for Internal Pressure

Credits

Created by Heet

Thadomal Shahani Engineering College (Tsec), Mumbai

Heet has created this Calculator and 200+ more calculators!

Verified by Prerana Bakli

University of Hawaiʻi at Mānoa (UH Manoa), Hawaii, USA

Prerana Bakli has verified this Calculator and 1600+ more calculators!

< Jacketed Reaction Vessel Calculators

Maximum Hoop Stress in Coil at Junction with Shell

LaTeX Go Maximum Hoop Stress in Coil at Junction with Shell = (Design Jacket Pressure*Internal Diameter of Half Coil)/(2*Thickness of Half Coil Jacket*Weld Joint Efficiency Factor for Coil)

Required Plate Thickness for Dimple Jacket

LaTeX Go Required Thickness of Dimple Jacket = Maximum Pitch between Steam Weld Centre Lines*sqrt(Design Jacket Pressure/(3*Allowable Stress for Jacket Material))

Required Thickness for Jacket Closer Member with Jacket Width

LaTeX Go Required Thickness for Jacket Closer Member = 0.886*Jacket Width*sqrt(Design Jacket Pressure/Allowable Stress for Jacket Material)

Jacket Width

LaTeX Go Jacket Width = (Inside Diameter of Jacket-Outer Diameter of Vessel)/2

Thickness of Jacket Shell for Internal Pressure Formula

LaTeX Go

What is Design Thickness?

Design thickness is a term used in structural engineering to refer to the thickness of a structural element (such as a beam, column, or plate) that has been calculated or specified based on the design requirements of the structure. The design thickness is the thickness that has been calculated or specified based on the structural requirements of the beam and the strength and deformability of the soil or foundation on which the beam will be supported. The design thickness of a bottom plate is typically determined by a structural engineer or using structural engineering software, and is used to ensure that the bottom plate is able to safely carry the loads that will be applied to it during the life of the structure.

How to Calculate Thickness of Jacket Shell for Internal Pressure?

Thickness of Jacket Shell for Internal Pressure calculator uses Required Thickness of Jacket = (Design Jacket Pressure*Internal Diameter of Shell)/((2*Allowable Stress for Jacket Material*Joint Efficiency for Shell)-Design Jacket Pressure) to calculate the Required Thickness of Jacket, Thickness of Jacket Shell for Internal Pressure formula is defined as the distance from the external part to the internal part of a jacket shell. Required Thickness of Jacket is denoted by t_rj symbol.

How to calculate Thickness of Jacket Shell for Internal Pressure using this online calculator? To use this online calculator for Thickness of Jacket Shell for Internal Pressure, enter Design Jacket Pressure (p_j), Internal Diameter of Shell (D_i), Allowable Stress for Jacket Material (f_j) & Joint Efficiency for Shell (J) and hit the calculate button. Here is how the Thickness of Jacket Shell for Internal Pressure calculation can be explained with given input values -> 772.4564 = (105000*1.5)/((2*120000000*0.85)-105000).

FAQ

What is Thickness of Jacket Shell for Internal Pressure?

Thickness of Jacket Shell for Internal Pressure formula is defined as the distance from the external part to the internal part of a jacket shell and is represented as t_rj = (p_j*D_i)/((2*f_j*J)-p_j) or Required Thickness of Jacket = (Design Jacket Pressure*Internal Diameter of Shell)/((2*Allowable Stress for Jacket Material*Joint Efficiency for Shell)-Design Jacket Pressure). Design Jacket Pressure refers to a type of pressure vessel designed to withstand high pressures and temperatures, typically used for containing gases or liquids under extreme conditions, Internal Diameter of Shell is a measurement of the distance of a straight line from one point on the inner wall of the object, through its center, to an opposite point also on the inside, Allowable Stress for Jacket Material at Design Temperature is defined as the material failure stress divided by a factor of safety greater than one & Joint Efficiency for Shell refers to the effectiveness of the joint between two adjacent sections of a cylindrical shell, such as in a pressure vessel or a storage tank.

How to calculate Thickness of Jacket Shell for Internal Pressure?

Thickness of Jacket Shell for Internal Pressure formula is defined as the distance from the external part to the internal part of a jacket shell is calculated using Required Thickness of Jacket = (Design Jacket Pressure*Internal Diameter of Shell)/((2*Allowable Stress for Jacket Material*Joint Efficiency for Shell)-Design Jacket Pressure). To calculate Thickness of Jacket Shell for Internal Pressure, you need Design Jacket Pressure (p_j), Internal Diameter of Shell (D_i), Allowable Stress for Jacket Material (f_j) & Joint Efficiency for Shell (J). With our tool, you need to enter the respective value for Design Jacket Pressure, Internal Diameter of Shell, Allowable Stress for Jacket Material & Joint Efficiency for Shell and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search