Thickness of Half Coil Jacket Calculator

✖Design Jacket Pressure refers to a type of pressure vessel designed to withstand high pressures and temperatures, typically used for containing gases or liquids under extreme conditions.ⓘ Design Jacket Pressure [p_j]			+10% -10%
✖Internal Diameter of Half Coil is a measurement of the distance of a straight line from one point on the inner wall of the object, through its center, to an opposite point also on the inside.ⓘ Internal Diameter of Half Coil [d_i]			+10% -10%
✖Allowable Stress for Jacket Material at Design Temperature is defined as the material failure stress divided by a factor of safety greater than one.ⓘ Allowable Stress for Jacket Material [f_j]			+10% -10%
✖Joint Efficiency for Shell refers to the effectiveness of the joint between two adjacent sections of a cylindrical shell, such as in a pressure vessel or a storage tank.ⓘ Joint Efficiency for Shell [J]			+10% -10%
✖Corrosion allowance is defined as an extra thickness normally added to carbon and low alloy steel to mitigate the CO2 corrosion rate.ⓘ Corrosion Allowance [c]			+10% -10%

✖Thickness of Half Coil Jacket can be determined by considering the heat transfer coefficient, the surface area of the coil, and the temperature difference.ⓘ Thickness of Half Coil Jacket [t_coil]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Jacketed Reaction Vessel Formulas PDF PDF Image

Thickness of Half Coil Jacket Solution

STEP 0: Pre-Calculation Summary

Formula Used

Thickness of Half Coil Jacket = (Design Jacket Pressure*Internal Diameter of Half Coil)/((2*Allowable Stress for Jacket Material*Joint Efficiency for Shell))+Corrosion Allowance
t_coil = (p_j*d_i)/((2*f_j*J))+c
This formula uses 6 Variables

Variables Used

Thickness of Half Coil Jacket - (Measured in Millimeter) - Thickness of Half Coil Jacket can be determined by considering the heat transfer coefficient, the surface area of the coil, and the temperature difference.
Design Jacket Pressure - (Measured in Newton per Square Millimeter) - Design Jacket Pressure refers to a type of pressure vessel designed to withstand high pressures and temperatures, typically used for containing gases or liquids under extreme conditions.
Internal Diameter of Half Coil - (Measured in Millimeter) - Internal Diameter of Half Coil is a measurement of the distance of a straight line from one point on the inner wall of the object, through its center, to an opposite point also on the inside.
Allowable Stress for Jacket Material - (Measured in Newton per Square Millimeter) - Allowable Stress for Jacket Material at Design Temperature is defined as the material failure stress divided by a factor of safety greater than one.
Joint Efficiency for Shell - Joint Efficiency for Shell refers to the effectiveness of the joint between two adjacent sections of a cylindrical shell, such as in a pressure vessel or a storage tank.
Corrosion Allowance - (Measured in Millimeter) - Corrosion allowance is defined as an extra thickness normally added to carbon and low alloy steel to mitigate the CO2 corrosion rate.

STEP 1: Convert Input(s) to Base Unit

Design Jacket Pressure: 0.105 Newton per Square Millimeter --> 0.105 Newton per Square Millimeter No Conversion Required
Internal Diameter of Half Coil: 54 Millimeter --> 54 Millimeter No Conversion Required
Allowable Stress for Jacket Material: 120 Newton per Square Millimeter --> 120 Newton per Square Millimeter No Conversion Required
Joint Efficiency for Shell: 0.85 --> No Conversion Required
Corrosion Allowance: 10.5 Millimeter --> 10.5 Millimeter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

t_coil = (p_j*d_i)/((2*f_j*J))+c --> (0.105*54)/((2*120*0.85))+10.5

Evaluating ... ...

t_coil = 10.5277941176471

STEP 3: Convert Result to Output's Unit

0.0105277941176471 Meter -->10.5277941176471 Millimeter (Check conversion here)

FINAL ANSWER

10.5277941176471 ≈ 10.52779 Millimeter <-- Thickness of Half Coil Jacket

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Chemical Engineering » Process Equipment Design » Jacketed Reaction Vessel » Thickness of Half Coil Jacket

Credits

Created by Heet

Thadomal Shahani Engineering College (Tsec), Mumbai

Heet has created this Calculator and 200+ more calculators!

Verified by Prerana Bakli

University of Hawaiʻi at Mānoa (UH Manoa), Hawaii, USA

Prerana Bakli has verified this Calculator and 1600+ more calculators!

< Jacketed Reaction Vessel Calculators

Maximum Hoop Stress in Coil at Junction with Shell

LaTeX Go Maximum Hoop Stress in Coil at Junction with Shell = (Design Jacket Pressure*Internal Diameter of Half Coil)/(2*Thickness of Half Coil Jacket*Weld Joint Efficiency Factor for Coil)

Required Plate Thickness for Dimple Jacket

LaTeX Go Required Thickness of Dimple Jacket = Maximum Pitch between Steam Weld Centre Lines*sqrt(Design Jacket Pressure/(3*Allowable Stress for Jacket Material))

Required Thickness for Jacket Closer Member with Jacket Width

LaTeX Go Required Thickness for Jacket Closer Member = 0.886*Jacket Width*sqrt(Design Jacket Pressure/Allowable Stress for Jacket Material)

Jacket Width

LaTeX Go Jacket Width = (Inside Diameter of Jacket-Outer Diameter of Vessel)/2

Thickness of Half Coil Jacket Formula

LaTeX Go

What is Design Thickness?

esign thickness is a term used in structural engineering to refer to the thickness of a structural element (such as a beam, column, or plate) that has been calculated or specified based on the design requirements of the structure. The design thickness is the thickness that has been calculated or specified based on the structural requirements of the beam and the strength and deformability of the soil or foundation on which the beam will be supported. The design thickness of a bottom plate is typically determined by a structural engineer or using structural engineering software, and is used to ensure that the bottom plate is able to safely carry the loads that will be applied to it during the life of the structure.

How to Calculate Thickness of Half Coil Jacket?

Thickness of Half Coil Jacket calculator uses Thickness of Half Coil Jacket = (Design Jacket Pressure*Internal Diameter of Half Coil)/((2*Allowable Stress for Jacket Material*Joint Efficiency for Shell))+Corrosion Allowance to calculate the Thickness of Half Coil Jacket, The Thickness of Half Coil Jacket formula is defined as the distance from the external part to the internal part of a Coil. Thickness of Half Coil Jacket is denoted by t_coil symbol.

How to calculate Thickness of Half Coil Jacket using this online calculator? To use this online calculator for Thickness of Half Coil Jacket, enter Design Jacket Pressure (p_j), Internal Diameter of Half Coil (d_i), Allowable Stress for Jacket Material (f_j), Joint Efficiency for Shell (J) & Corrosion Allowance (c) and hit the calculate button. Here is how the Thickness of Half Coil Jacket calculation can be explained with given input values -> 10527.79 = (105000*0.054)/((2*120000000*0.85))+0.0105.

FAQ

What is Thickness of Half Coil Jacket?

The Thickness of Half Coil Jacket formula is defined as the distance from the external part to the internal part of a Coil and is represented as t_coil = (p_j*d_i)/((2*f_j*J))+c or Thickness of Half Coil Jacket = (Design Jacket Pressure*Internal Diameter of Half Coil)/((2*Allowable Stress for Jacket Material*Joint Efficiency for Shell))+Corrosion Allowance. Design Jacket Pressure refers to a type of pressure vessel designed to withstand high pressures and temperatures, typically used for containing gases or liquids under extreme conditions, Internal Diameter of Half Coil is a measurement of the distance of a straight line from one point on the inner wall of the object, through its center, to an opposite point also on the inside, Allowable Stress for Jacket Material at Design Temperature is defined as the material failure stress divided by a factor of safety greater than one, Joint Efficiency for Shell refers to the effectiveness of the joint between two adjacent sections of a cylindrical shell, such as in a pressure vessel or a storage tank & Corrosion allowance is defined as an extra thickness normally added to carbon and low alloy steel to mitigate the CO2 corrosion rate.

How to calculate Thickness of Half Coil Jacket?

The Thickness of Half Coil Jacket formula is defined as the distance from the external part to the internal part of a Coil is calculated using Thickness of Half Coil Jacket = (Design Jacket Pressure*Internal Diameter of Half Coil)/((2*Allowable Stress for Jacket Material*Joint Efficiency for Shell))+Corrosion Allowance. To calculate Thickness of Half Coil Jacket, you need Design Jacket Pressure (p_j), Internal Diameter of Half Coil (d_i), Allowable Stress for Jacket Material (f_j), Joint Efficiency for Shell (J) & Corrosion Allowance (c). With our tool, you need to enter the respective value for Design Jacket Pressure, Internal Diameter of Half Coil, Allowable Stress for Jacket Material, Joint Efficiency for Shell & Corrosion Allowance and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search