Diameter of Drill Bit given Length of Approach Solution

STEP 0: Pre-Calculation Summary
Formula Used
Diameter of Drill Bit = 2*Approach Distance/tan(pi/2-Drill Point Angle/2)
D = 2*A/tan(pi/2-θ/2)
This formula uses 1 Constants, 1 Functions, 3 Variables
Constants Used
pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288
Functions Used
tan - The tangent of an angle is a trigonometric ratio of the length of the side opposite an angle to the length of the side adjacent to an angle in a right triangle., tan(Angle)
Variables Used
Diameter of Drill Bit - (Measured in Meter) - Diameter of drill bit is essentially the straight distance across the widest part of the cutting edge (lips) of the drill bit. It determines the width of the hole it will create on workpiece.
Approach Distance - (Measured in Meter) - Approach Distance is the extra distance the drill travels before it starts cutting into the workpiece. It allows the tool to reach its cutting speed and position itself properly for an accurate hole.
Drill Point Angle - (Measured in Radian) - Drill Point Angle is the angle between the two cutting edges (lips) of a drill bit at its tip. This angle affects how aggressively the bit cuts and what materials it's suited for.
STEP 1: Convert Input(s) to Base Unit
Approach Distance: 12.5 Millimeter --> 0.0125 Meter (Check conversion ​here)
Drill Point Angle: 135 Degree --> 2.3561944901919 Radian (Check conversion ​here)
STEP 2: Evaluate Formula
Substituting Input Values in Formula
D = 2*A/tan(pi/2-θ/2) --> 2*0.0125/tan(pi/2-2.3561944901919/2)
Evaluating ... ...
D = 0.0603553390592894
STEP 3: Convert Result to Output's Unit
0.0603553390592894 Meter -->60.3553390592894 Millimeter (Check conversion ​here)
FINAL ANSWER
60.3553390592894 60.35534 Millimeter <-- Diameter of Drill Bit
(Calculation completed in 00.004 seconds)

Credits

Creator Image
Created by Kumar Siddhant
Indian Institute of Information Technology, Design and Manufacturing (IIITDM), Jabalpur
Kumar Siddhant has created this Calculator and 400+ more calculators!
Verifier Image
Verified by Anshika Arya
National Institute Of Technology (NIT), Hamirpur
Anshika Arya has verified this Calculator and 2500+ more calculators!

Drilling Operation Calculators

Diameter of Drill Bit given Length of Approach
​ LaTeX ​ Go Diameter of Drill Bit = 2*Approach Distance/tan(pi/2-Drill Point Angle/2)
Machining Time for Drilling Operation
​ LaTeX ​ Go Machining Time = Length of Cut/(Feed Rate*Rotational Frequency of Drill-bit)
Drill Point Angle for given Length of Approach
​ LaTeX ​ Go Drill Point Angle = 2*atan(0.5*Diameter of Drill Bit/Approach Distance)
Length of Approach for Drilling Operation
​ LaTeX ​ Go Approach Distance = 0.5*Diameter of Drill Bit*cot(Drill Point Angle/2)

Diameter of Drill Bit given Length of Approach Formula

​LaTeX ​Go
Diameter of Drill Bit = 2*Approach Distance/tan(pi/2-Drill Point Angle/2)
D = 2*A/tan(pi/2-θ/2)

Why Drill is a Multi-Point Cutting Tool?

If a cutter contains more than one cutting edge that can simultaneously partake in material removal action during machining, then it is called a multipoint cutter. Sometimes drill is classified as a double-point cutting tool because common metal cutting drills contain only two cutting edges; however, drills may contain more than two (3 to 6) cutting edges also (for example, wood cutting twist drills).

What is Shank of a drill-bit?

The shank of a drill bit is the end of the bit that is gripped by the chuck of a drill. It's the part you insert into the drill and tighten to hold the bit securely in place. You can think of the shank as the handle of a tool. It's how you hold and control the drill bit while the cutting edges (lips) at the other end do the actual work of creating the hole.

How to Calculate Diameter of Drill Bit given Length of Approach?

Diameter of Drill Bit given Length of Approach calculator uses Diameter of Drill Bit = 2*Approach Distance/tan(pi/2-Drill Point Angle/2) to calculate the Diameter of Drill Bit, The diameter of Drill Bit given Length of Approach is a method to determine the straight distance across the widest part of the cutting edge (lips) of the drill bit, when length of approach is known. It's typically measured in millimeters (mm) or inches (in) and is usually printed on the shank of the drill bit. Diameter of Drill Bit is denoted by D symbol.

How to calculate Diameter of Drill Bit given Length of Approach using this online calculator? To use this online calculator for Diameter of Drill Bit given Length of Approach, enter Approach Distance (A) & Drill Point Angle (θ) and hit the calculate button. Here is how the Diameter of Drill Bit given Length of Approach calculation can be explained with given input values -> 60355.34 = 2*0.0125/tan(pi/2-2.3561944901919/2).

FAQ

What is Diameter of Drill Bit given Length of Approach?
The diameter of Drill Bit given Length of Approach is a method to determine the straight distance across the widest part of the cutting edge (lips) of the drill bit, when length of approach is known. It's typically measured in millimeters (mm) or inches (in) and is usually printed on the shank of the drill bit and is represented as D = 2*A/tan(pi/2-θ/2) or Diameter of Drill Bit = 2*Approach Distance/tan(pi/2-Drill Point Angle/2). Approach Distance is the extra distance the drill travels before it starts cutting into the workpiece. It allows the tool to reach its cutting speed and position itself properly for an accurate hole & Drill Point Angle is the angle between the two cutting edges (lips) of a drill bit at its tip. This angle affects how aggressively the bit cuts and what materials it's suited for.
How to calculate Diameter of Drill Bit given Length of Approach?
The diameter of Drill Bit given Length of Approach is a method to determine the straight distance across the widest part of the cutting edge (lips) of the drill bit, when length of approach is known. It's typically measured in millimeters (mm) or inches (in) and is usually printed on the shank of the drill bit is calculated using Diameter of Drill Bit = 2*Approach Distance/tan(pi/2-Drill Point Angle/2). To calculate Diameter of Drill Bit given Length of Approach, you need Approach Distance (A) & Drill Point Angle (θ). With our tool, you need to enter the respective value for Approach Distance & Drill Point Angle and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!