Test Current in Open Circuit Time Constants Method of CS Amplifier Calculator

✖Transconductance is the ratio of the change in current at the output terminal to the change in the voltage at the input terminal of an active device.ⓘ Transconductance [g_m]			+10% -10%
✖Gate to source voltage of transistor is the voltage that falls across the gate-source terminal of the transistor.ⓘ Gate to Source Voltage [V_gs]			+10% -10%
✖Test voltage involves placing an extra-high voltage across the insulation barrier of the device for one minute.ⓘ Test Voltage [v_x]			+10% -10%
✖Load resistance is the cumulative resistance of a circuit, as seen by the voltage, current, or power source driving that circuit.ⓘ Load Resistance [R_L]			+10% -10%

✖Test current is a flow of electrical charge carriers, usually electrons or electron-deficient atoms.ⓘ Test Current in Open Circuit Time Constants Method of CS Amplifier [i_x]

⎘ Copy

👎

Formula

✖

Test Current in Open Circuit Time Constants Method of CS Amplifier

Formula

i x = g m \cdot V gs + \frac{v x + V gs}{R L}

Example

29.48188 mA = 4.8 mS \cdot 4 V + \frac{11.32 V + 4 V}{1.49 kΩ}

Calculator

LaTeX

Reset

👍

Download High Frequency Response Amplifiers Formula PDF PDF Image

Test Current in Open Circuit Time Constants Method of CS Amplifier Solution

STEP 0: Pre-Calculation Summary

Formula Used

Test Current = Transconductance*Gate to Source Voltage+(Test Voltage+Gate to Source Voltage)/Load Resistance
i_x = g_m*V_gs+(v_x+V_gs)/R_L
This formula uses 5 Variables

Variables Used

Test Current - (Measured in Ampere) - Test current is a flow of electrical charge carriers, usually electrons or electron-deficient atoms.
Transconductance - (Measured in Siemens) - Transconductance is the ratio of the change in current at the output terminal to the change in the voltage at the input terminal of an active device.
Gate to Source Voltage - (Measured in Volt) - Gate to source voltage of transistor is the voltage that falls across the gate-source terminal of the transistor.
Test Voltage - (Measured in Volt) - Test voltage involves placing an extra-high voltage across the insulation barrier of the device for one minute.
Load Resistance - (Measured in Ohm) - Load resistance is the cumulative resistance of a circuit, as seen by the voltage, current, or power source driving that circuit.

STEP 1: Convert Input(s) to Base Unit

Transconductance: 4.8 Millisiemens --> 0.0048 Siemens (Check conversion here)
Gate to Source Voltage: 4 Volt --> 4 Volt No Conversion Required
Test Voltage: 11.32 Volt --> 11.32 Volt No Conversion Required
Load Resistance: 1.49 Kilohm --> 1490 Ohm (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

i_x = g_m*V_gs+(v_x+V_gs)/R_L --> 0.0048*4+(11.32+4)/1490

Evaluating ... ...

i_x = 0.0294818791946309

STEP 3: Convert Result to Output's Unit

0.0294818791946309 Ampere -->29.4818791946309 Milliampere (Check conversion here)

FINAL ANSWER

29.4818791946309 ≈ 29.48188 Milliampere <-- Test Current

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Electronics » Amplifiers » High Frequency Response Amplifiers » Response of CS Amplifier » Test Current in Open Circuit Time Constants Method of CS Amplifier

Credits

Created by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has created this Calculator and 600+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Response of CS Amplifier Calculators

Output Voltage of CS Amplifier

Go Output Voltage = Transconductance*Gate to Source Voltage*Load Resistance

Equivalent Signal Resistance of CS Amplifier

Go Internal Small Signal Resistance = 1/((1/Signal Resistance+1/Output Resistance))

Frequency of Zero Transmission of CS Amplifier

Go Transmission Frequency = 1/(Bypass Capacitor*Signal Resistance)

Midband Gain of CS Amplifier

Go Mid Band Gain = Output Voltage/Small Signal Voltage

< Common Stage Amplifiers Calculators

Effective High Frequency Time Constant of CE Amplifier

Go Effective High Frequency Time Constant = Base Emitter Capacitance*Signal Resistance+(Collector Base Junction Capacitance*(Signal Resistance*(1+Transconductance*Load Resistance)+Load Resistance))+(Capacitance*Load Resistance)

High-Frequency Band given Complex Frequency Variable

Go Amplifier Gain in Mid Band = sqrt(((1+(3 dB Frequency/Frequency))*(1+(3 dB Frequency/Frequency Observed)))/((1+(3 dB Frequency/Pole Frequency))*(1+(3 dB Frequency/Second Pole Frequency))))

Collector Base Junction Resistance of CE Amplifier

Go Collector Resistance = Signal Resistance*(1+Transconductance*Load Resistance)+Load Resistance

Amplifier Bandwidth in Discrete-Circuit Amplifier

Go Amplifier Bandwidth = High Frequency-Low Frequency

Test Current in Open Circuit Time Constants Method of CS Amplifier Formula

Test Current = Transconductance*Gate to Source Voltage+(Test Voltage+Gate to Source Voltage)/Load Resistance
i_x = g_m*V_gs+(v_x+V_gs)/R_L

What is CS amplifier?

In electronics, a common-source amplifier is one of three basic single-stage field-effect transistor (FET) amplifier topologies, typically used as a voltage or transconductance amplifier. The easiest way to tell if a FET is a common source, common drain, or common gate is to examine where the signal enters and leaves.

How to Calculate Test Current in Open Circuit Time Constants Method of CS Amplifier?

Test Current in Open Circuit Time Constants Method of CS Amplifier calculator uses Test Current = Transconductance*Gate to Source Voltage+(Test Voltage+Gate to Source Voltage)/Load Resistance to calculate the Test Current, The Test current in open circuit time constants method of CS amplifier formula is defined as the current at which the Zener breakdown voltage and equivalent internal impedance specifications are guaranteed. Currents are higher than the test current result in slightly higher breakdown voltage and lower internal impedance. Test Current is denoted by i_x symbol.

How to calculate Test Current in Open Circuit Time Constants Method of CS Amplifier using this online calculator? To use this online calculator for Test Current in Open Circuit Time Constants Method of CS Amplifier, enter Transconductance (g_m), Gate to Source Voltage (V_gs), Test Voltage (v_x) & Load Resistance (R_L) and hit the calculate button. Here is how the Test Current in Open Circuit Time Constants Method of CS Amplifier calculation can be explained with given input values -> 29420.15 = 0.0048*4+(11.32+4)/1490.

FAQ

What is Test Current in Open Circuit Time Constants Method of CS Amplifier?

The Test current in open circuit time constants method of CS amplifier formula is defined as the current at which the Zener breakdown voltage and equivalent internal impedance specifications are guaranteed. Currents are higher than the test current result in slightly higher breakdown voltage and lower internal impedance and is represented as i_x = g_m*V_gs+(v_x+V_gs)/R_L or Test Current = Transconductance*Gate to Source Voltage+(Test Voltage+Gate to Source Voltage)/Load Resistance. Transconductance is the ratio of the change in current at the output terminal to the change in the voltage at the input terminal of an active device, Gate to source voltage of transistor is the voltage that falls across the gate-source terminal of the transistor, Test voltage involves placing an extra-high voltage across the insulation barrier of the device for one minute & Load resistance is the cumulative resistance of a circuit, as seen by the voltage, current, or power source driving that circuit.

How to calculate Test Current in Open Circuit Time Constants Method of CS Amplifier?

The Test current in open circuit time constants method of CS amplifier formula is defined as the current at which the Zener breakdown voltage and equivalent internal impedance specifications are guaranteed. Currents are higher than the test current result in slightly higher breakdown voltage and lower internal impedance is calculated using Test Current = Transconductance*Gate to Source Voltage+(Test Voltage+Gate to Source Voltage)/Load Resistance. To calculate Test Current in Open Circuit Time Constants Method of CS Amplifier, you need Transconductance (g_m), Gate to Source Voltage (V_gs), Test Voltage (v_x) & Load Resistance (R_L). With our tool, you need to enter the respective value for Transconductance, Gate to Source Voltage, Test Voltage & Load Resistance and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search