Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners Calculator

✖The allowable bearing stress is the maximum bearing stress that can be applied to the structure such that it is safe against instability due to shear failure.ⓘ Allowable Bearing Stress [F_p]

+10%

-10%

✖The tensile strength of connected part is the maximum stress that a material can bear before breaking when it is allowed to be stretched or pulled.ⓘ Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners [F_u]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Load, Stress and Fasteners Formulas PDF PDF Image

Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners Solution

STEP 0: Pre-Calculation Summary

Formula Used

Tensile Strength of connected part = Allowable Bearing Stress/0.80
F_u = F_p/0.80
This formula uses 2 Variables

Variables Used

Tensile Strength of connected part - (Measured in Megapascal) - The tensile strength of connected part is the maximum stress that a material can bear before breaking when it is allowed to be stretched or pulled.
Allowable Bearing Stress - (Measured in Megapascal) - The allowable bearing stress is the maximum bearing stress that can be applied to the structure such that it is safe against instability due to shear failure.

STEP 1: Convert Input(s) to Base Unit

Allowable Bearing Stress: 107 Megapascal --> 107 Megapascal No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

F_u = F_p/0.80 --> 107/0.80

Evaluating ... ...

F_u = 133.75

STEP 3: Convert Result to Output's Unit

133750000 Pascal -->133.75 Megapascal (Check conversion here)

FINAL ANSWER

133.75 Megapascal <-- Tensile Strength of connected part

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Civil » Bridge and Suspension Cable » Load, Stress and Fasteners » Bearing on Milled Surfaces and Bridge Fasteners » Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners

Credits

Created by Ayush Singh

Gautam Buddha University (GBU), Greater Noida

Ayush Singh has created this Calculator and 50+ more calculators!

Verified by Mithila Muthamma PA

Coorg Institute of Technology (CIT), Coorg

Mithila Muthamma PA has verified this Calculator and 700+ more calculators!

< Bearing on Milled Surfaces and Bridge Fasteners Calculators

Allowable Stress for Expansion Rollers and Rockers where Diameter is from 635 mm to 3175 mm

LaTeX Go Allowable Stress = ((Yield Strength of Steel-13)/20)*3*sqrt(Diameter of Roller or Rocker)

Diameter of Roller or Rocker for d from 635 to 3125mm

LaTeX Go Diameter of Roller or Rocker = (Allowable Stress/(((Yield Strength of Steel-13)/20)*3))^2

Allowable Stress for Expansion Rollers and Rockers where Diameter is up to 635 mm

LaTeX Go Allowable Stress = ((Yield Strength of Steel-13)/20)*0.6*Diameter of Roller or Rocker

Diameter of Roller or Rocker for d up to 635 mm

LaTeX Go Diameter of Roller or Rocker = Allowable Stress/(((Yield Strength of Steel)/20)*0.6)

Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners Formula

LaTeX Go

Tensile Strength of connected part = Allowable Bearing Stress/0.80
F_u = F_p/0.80

What is Tensile Strength?

Tensile Strength of bolts is the maximum load in tension (pulling apart) which a material can withstand before breaking or fracturing, whereas yield Strength is the maximum load at which a material exhibits a specific permanent deformation.

What is Allowable Bearing Stress?

Allowable bearing stress is a value based on an arbitrary amount of deformation of a body subjected to a bearing pressure. The bearing stress criteria for aluminum alloys, if applied to heat-treated steel, would permit allowable stresses as much as 50 per cent greater than those used at present for steel.

How to Calculate Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners?

Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners calculator uses Tensile Strength of connected part = Allowable Bearing Stress/0.80 to calculate the Tensile Strength of connected part, The Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners formula is defined as the maximum load in tension that a material which is connected can withstand before breaking or fracturing. Tensile Strength of connected part is denoted by F_u symbol.

How to calculate Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners using this online calculator? To use this online calculator for Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners, enter Allowable Bearing Stress (F_p) and hit the calculate button. Here is how the Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners calculation can be explained with given input values -> 0.000134 = 107000000/0.80.

FAQ

What is Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners?

The Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners formula is defined as the maximum load in tension that a material which is connected can withstand before breaking or fracturing and is represented as F_u = F_p/0.80 or Tensile Strength of connected part = Allowable Bearing Stress/0.80. The allowable bearing stress is the maximum bearing stress that can be applied to the structure such that it is safe against instability due to shear failure.

How to calculate Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners?

The Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners formula is defined as the maximum load in tension that a material which is connected can withstand before breaking or fracturing is calculated using Tensile Strength of connected part = Allowable Bearing Stress/0.80. To calculate Tensile Strength of Connected Part given Allowable Bearing Stress on Milled Stiffeners, you need Allowable Bearing Stress (F_p). With our tool, you need to enter the respective value for Allowable Bearing Stress and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Tensile Strength of connected part?

In this formula, Tensile Strength of connected part uses Allowable Bearing Stress. We can use 1 other way(s) to calculate the same, which is/are as follows -

Tensile Strength of connected part = Allowable Bearing Stress/1.35

Home

FREE PDFs

🔍 Search