LCM calculator

Surface Resistance of Guide Walls Calculator

Engineering Chemistry Financial Health More >>

↳

Electronics Chemical Engineering Civil Electrical More >>

⤿

Microwave Theory Amplifiers Analog Communications Analog Electronics More >>

⤿

Microwave Devices Microwave Semiconductor Devices Microwave Tubes and Circuits

✖Frequency the number of waves that pass a fixed point in unit time; also, the number of cycles or vibrations undergone during one unit of time by a body in periodic motion in a waveguide.ⓘ Frequency [f]			+10% -10%
✖Magnetic Permeability is a property of a magnetic material which supports the formation of a magnetic field.ⓘ Magnetic Permeability [μ]			+10% -10%
✖Conductivity (or specific conductance) of an electrolyte solution is a measure of its ability to conduct electricity. The SI unit of conductivity is siemens per meter (S/m).ⓘ Conductivity [σ]			+10% -10%

✖Surface Resistance is the measure of the electrical resistance of a surface layer to a current.ⓘ Surface Resistance of Guide Walls [R_s]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Microwave Theory Formula PDF PDF Image

Surface Resistance of Guide Walls Solution

STEP 0: Pre-Calculation Summary

Formula Used

Surface Resistance = sqrt((pi*Frequency*Magnetic Permeability)/(Conductivity))
R_s = sqrt((pi*f*μ)/(σ))
This formula uses 1 Constants, 1 Functions, 4 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Functions Used

sqrt - A square root function is a function that takes a non-negative number as an input and returns the square root of the given input number., sqrt(Number)

Variables Used

Surface Resistance - (Measured in Ohm) - Surface Resistance is the measure of the electrical resistance of a surface layer to a current.
Frequency - (Measured in Hertz) - Frequency the number of waves that pass a fixed point in unit time; also, the number of cycles or vibrations undergone during one unit of time by a body in periodic motion in a waveguide.
Magnetic Permeability - (Measured in Henry per Meter) - Magnetic Permeability is a property of a magnetic material which supports the formation of a magnetic field.
Conductivity - (Measured in Siemens per Meter) - Conductivity (or specific conductance) of an electrolyte solution is a measure of its ability to conduct electricity. The SI unit of conductivity is siemens per meter (S/m).

STEP 1: Convert Input(s) to Base Unit

Frequency: 55.02 Hertz --> 55.02 Hertz No Conversion Required
Magnetic Permeability: 1.3 Henry per Meter --> 1.3 Henry per Meter No Conversion Required
Conductivity: 0.1 Siemens per Meter --> 0.1 Siemens per Meter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

R_s = sqrt((pi*f*μ)/(σ)) --> sqrt((pi*55.02*1.3)/(0.1))

Evaluating ... ...

R_s = 47.4031176338291

STEP 3: Convert Result to Output's Unit

47.4031176338291 Ohm -->0.0474031176338291 Kilohm (Check conversion here)

FINAL ANSWER

0.0474031176338291 ≈ 0.047403 Kilohm <-- Surface Resistance

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Electronics » Microwave Theory » Microwave Devices » Surface Resistance of Guide Walls

Credits

Created by Sai Sudha Vani Priya Lanka

Dayananda Sagar University (DSU), Bengaluru, Karnataka, India-560100

Sai Sudha Vani Priya Lanka has created this Calculator and 10+ more calculators!

Verified by Parminder Singh

Chandigarh University (CU), Punjab

Parminder Singh has verified this Calculator and 500+ more calculators!

< Microwave Devices Calculators

Force Exerted on Particle

LaTeX Go Force Exerted on Particle = (Charge of a Particle*Velocity of a Charged Particle)*Magnetic Flux Density

Characteristic Wave Impedance

LaTeX Go Characteristic Wave Impedance = (Angular Frequency*Magnetic Permeability)/(Phase Constant)

Quality Factor

LaTeX Go Quality Factor = (Angular Frequency*Maximum Stored Energy)/(Average Power Loss)

Power Losses for TEM Mode

LaTeX Go Power Losses for the TEM Mode = 2*Attenuation Constant*Transmitting Power

Surface Resistance of Guide Walls Formula

LaTeX Go

Surface Resistance = sqrt((pi*Frequency*Magnetic Permeability)/(Conductivity))
R_s = sqrt((pi*f*μ)/(σ))

Why is surface resistivity important in textiles?

In contrast to many bulk materials, textiles have high porosity and often show anisotropy. Therefore, the surface resistivity is not a valuable indication in most of the cases; instead, the surface resistance per unit area is more critical. Preferably, the resistance per unit area should be given with direction.

How to Calculate Surface Resistance of Guide Walls?

Surface Resistance of Guide Walls calculator uses Surface Resistance = sqrt((pi*Frequency*Magnetic Permeability)/(Conductivity)) to calculate the Surface Resistance, The Surface Resistance of Guide Walls measures the capacity of a material to resist the flow of electricity. It is the ratio of applied voltage to the current flowing between two electrodes in contact with the surface of a material. Surface Resistance is denoted by R_s symbol.

How to calculate Surface Resistance of Guide Walls using this online calculator? To use this online calculator for Surface Resistance of Guide Walls, enter Frequency (f), Magnetic Permeability (μ) & Conductivity (σ) and hit the calculate button. Here is how the Surface Resistance of Guide Walls calculation can be explained with given input values -> 4.7E-5 = sqrt((pi*55.02*1.3)/(0.1)).

FAQ

What is Surface Resistance of Guide Walls?

The Surface Resistance of Guide Walls measures the capacity of a material to resist the flow of electricity. It is the ratio of applied voltage to the current flowing between two electrodes in contact with the surface of a material and is represented as R_s = sqrt((pi*f*μ)/(σ)) or Surface Resistance = sqrt((pi*Frequency*Magnetic Permeability)/(Conductivity)). Frequency the number of waves that pass a fixed point in unit time; also, the number of cycles or vibrations undergone during one unit of time by a body in periodic motion in a waveguide, Magnetic Permeability is a property of a magnetic material which supports the formation of a magnetic field & Conductivity (or specific conductance) of an electrolyte solution is a measure of its ability to conduct electricity. The SI unit of conductivity is siemens per meter (S/m).

How to calculate Surface Resistance of Guide Walls?

The Surface Resistance of Guide Walls measures the capacity of a material to resist the flow of electricity. It is the ratio of applied voltage to the current flowing between two electrodes in contact with the surface of a material is calculated using Surface Resistance = sqrt((pi*Frequency*Magnetic Permeability)/(Conductivity)). To calculate Surface Resistance of Guide Walls, you need Frequency (f), Magnetic Permeability (μ) & Conductivity (σ). With our tool, you need to enter the respective value for Frequency, Magnetic Permeability & Conductivity and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search