Surface Area of Bay or Basin given Total Maximum Discharge Calculator

✖Maximum Discharge of Total Inlets is the maximum volume flow rate passing a particular location during an event.ⓘ Maximum Discharge of Total Inlets [Q_max]			+10% -10%
✖Tidal Period is the time taken for a specific site on Earth to rotate from an exact point under moon to same point under moon, also known as “tidal day” and it’s slightly longer than a solar day.ⓘ Tidal Period [T]			+10% -10%
✖Ocean Tide Amplitude is the height difference between high and low tides, reflecting gravitational forces from the moon and sun.ⓘ Ocean Tide Amplitude [a_o]			+10% -10%
✖Maximum Velocity in the Inlet Throat [length/time] is measure of speed in the inlet throat.ⓘ Maximum Velocity in the Inlet Throat [V_max]			+10% -10%

✖Surface Area of Bay is defined as a small body of water set off from the main body.ⓘ Surface Area of Bay or Basin given Total Maximum Discharge [A_b]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Bay Superelevation, Effect of Freshwater Inflow, Multiple Inlets and Wave Current Interaction Formulas PDF PDF Image

Surface Area of Bay or Basin given Total Maximum Discharge Solution

STEP 0: Pre-Calculation Summary

Formula Used

Surface Area of Bay = (Maximum Discharge of Total Inlets*Tidal Period)/(2*pi*Ocean Tide Amplitude*Maximum Velocity in the Inlet Throat)
A_b = (Q_max*T)/(2*pi*a_o*V_max)
This formula uses 1 Constants, 5 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Variables Used

Surface Area of Bay - (Measured in Square Meter) - Surface Area of Bay is defined as a small body of water set off from the main body.
Maximum Discharge of Total Inlets - (Measured in Cubic Meter per Second) - Maximum Discharge of Total Inlets is the maximum volume flow rate passing a particular location during an event.
Tidal Period - (Measured in Second) - Tidal Period is the time taken for a specific site on Earth to rotate from an exact point under moon to same point under moon, also known as “tidal day” and it’s slightly longer than a solar day.
Ocean Tide Amplitude - (Measured in Meter) - Ocean Tide Amplitude is the height difference between high and low tides, reflecting gravitational forces from the moon and sun.
Maximum Velocity in the Inlet Throat - (Measured in Meter per Second) - Maximum Velocity in the Inlet Throat [length/time] is measure of speed in the inlet throat.

STEP 1: Convert Input(s) to Base Unit

Maximum Discharge of Total Inlets: 10.15 Cubic Meter per Second --> 10.15 Cubic Meter per Second No Conversion Required
Tidal Period: 130 Second --> 130 Second No Conversion Required
Ocean Tide Amplitude: 4 Meter --> 4 Meter No Conversion Required
Maximum Velocity in the Inlet Throat: 35 Meter per Second --> 35 Meter per Second No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

A_b = (Q_max*T)/(2*pi*a_o*V_max) --> (10.15*130)/(2*pi*4*35)

Evaluating ... ...

A_b = 1.50003533864111

STEP 3: Convert Result to Output's Unit

1.50003533864111 Square Meter --> No Conversion Required

FINAL ANSWER

1.50003533864111 ≈ 1.500035 Square Meter <-- Surface Area of Bay

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Civil » Coastal and Ocean Engineering » Hydrodynamics of Tidal Inlets 1 » Inlet Hydrodynamics » Bay Superelevation, Effect of Freshwater Inflow, Multiple Inlets and Wave Current Interaction » Multiple Inlets » Surface Area of Bay or Basin given Total Maximum Discharge

Credits

Created by Mithila Muthamma PA

Coorg Institute of Technology (CIT), Coorg

Mithila Muthamma PA has created this Calculator and 2000+ more calculators!

Verified by M Naveen

National Institute of Technology (NIT), Warangal

M Naveen has verified this Calculator and 900+ more calculators!

< Multiple Inlets Calculators

Ocean Tide Amplitude given Total Maximum Discharge for Total of all Inlets

LaTeX Go Ocean Tide Amplitude = (Maximum Discharge of Total Inlets*Tidal Period)/(2*pi*Surface Area of Bay*Maximum Velocity in the Inlet Throat)

Surface Area of Bay or Basin given Total Maximum Discharge

LaTeX Go Surface Area of Bay = (Maximum Discharge of Total Inlets*Tidal Period)/(2*pi*Ocean Tide Amplitude*Maximum Velocity in the Inlet Throat)

Tidal Period given Total Maximum Discharge for Total of all Inlets

LaTeX Go Tidal Period = (2*pi*Ocean Tide Amplitude*Maximum Velocity in the Inlet Throat*Surface Area of Bay)/Maximum Discharge of Total Inlets

Total Maximum Discharge for Total of all Inlets

LaTeX Go Maximum Discharge of Total Inlets = (2*pi*Ocean Tide Amplitude*Surface Area of Bay*Maximum Velocity in the Inlet Throat)/Tidal Period

Surface Area of Bay or Basin given Total Maximum Discharge Formula

LaTeX Go

Surface Area of Bay = (Maximum Discharge of Total Inlets*Tidal Period)/(2*pi*Ocean Tide Amplitude*Maximum Velocity in the Inlet Throat)
A_b = (Q_max*T)/(2*pi*a_o*V_max)

What is Bay Superelevation?

A Superelevation of the bay means that the average level of the bay is greater than the average elevation of the ocean over a given time period. An obvious cause of this effect is the introduction of fresh water into the bay from local rivers and streams. The effect of long-term (months or years) rise in sea level causing a long-term rise in bay level is not included in this definition of bay superelevation, since both sea and bay are responding simultaneously. The bay may not rise at the same rate as the sea due to possible
circulation effects if multiple inlets connect the bay to the ocean.

What is a basin?

A basin is a depression, or dip, in the Earth's surface. Basins are shaped like bowls, with sides higher than the bottom. ... The major types of basins are river drainage basins, structural basins, and ocean basins. River Drainage Basins. A river drainage basin is an area drained by a river and all of its tributaries.

How to Calculate Surface Area of Bay or Basin given Total Maximum Discharge?

Surface Area of Bay or Basin given Total Maximum Discharge calculator uses Surface Area of Bay = (Maximum Discharge of Total Inlets*Tidal Period)/(2*pi*Ocean Tide Amplitude*Maximum Velocity in the Inlet Throat) to calculate the Surface Area of Bay, The Surface Area of Bay or Basin given Total Maximum Discharge is defined as the area of a small body of water set off from the main body. Surface Area of Bay is denoted by A_b symbol.

How to calculate Surface Area of Bay or Basin given Total Maximum Discharge using this online calculator? To use this online calculator for Surface Area of Bay or Basin given Total Maximum Discharge, enter Maximum Discharge of Total Inlets (Q_max), Tidal Period (T), Ocean Tide Amplitude (a_o) & Maximum Velocity in the Inlet Throat (V_max) and hit the calculate button. Here is how the Surface Area of Bay or Basin given Total Maximum Discharge calculation can be explained with given input values -> 1.500035 = (10.15*130)/(2*pi*4*35).

FAQ

What is Surface Area of Bay or Basin given Total Maximum Discharge?

The Surface Area of Bay or Basin given Total Maximum Discharge is defined as the area of a small body of water set off from the main body and is represented as A_b = (Q_max*T)/(2*pi*a_o*V_max) or Surface Area of Bay = (Maximum Discharge of Total Inlets*Tidal Period)/(2*pi*Ocean Tide Amplitude*Maximum Velocity in the Inlet Throat). Maximum Discharge of Total Inlets is the maximum volume flow rate passing a particular location during an event, Tidal Period is the time taken for a specific site on Earth to rotate from an exact point under moon to same point under moon, also known as “tidal day” and it’s slightly longer than a solar day, Ocean Tide Amplitude is the height difference between high and low tides, reflecting gravitational forces from the moon and sun & Maximum Velocity in the Inlet Throat [length/time] is measure of speed in the inlet throat.

How to calculate Surface Area of Bay or Basin given Total Maximum Discharge?

The Surface Area of Bay or Basin given Total Maximum Discharge is defined as the area of a small body of water set off from the main body is calculated using Surface Area of Bay = (Maximum Discharge of Total Inlets*Tidal Period)/(2*pi*Ocean Tide Amplitude*Maximum Velocity in the Inlet Throat). To calculate Surface Area of Bay or Basin given Total Maximum Discharge, you need Maximum Discharge of Total Inlets (Q_max), Tidal Period (T), Ocean Tide Amplitude (a_o) & Maximum Velocity in the Inlet Throat (V_max). With our tool, you need to enter the respective value for Maximum Discharge of Total Inlets, Tidal Period, Ocean Tide Amplitude & Maximum Velocity in the Inlet Throat and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search