Stress when Concentrated Load is Applied Close to Beam End Calculator

✖Concentrated Load of Reaction is the reaction force that is assumed to act at a single point on the structure.ⓘ Concentrated Load of Reaction [R]			+10% -10%
✖Web Thickness is the thickness of the web section in the member of I section.ⓘ Web Thickness [t_w]			+10% -10%
✖Bearing or Plate Length is the length along the beam under which a high concentration of stresses due to concentrated loads is transferred to the supporting structure below.ⓘ Bearing or Plate Length [N]			+10% -10%
✖The Distance from Flange to Web Fillet is the total distance from the outer face of the flange to the web toe of the fillet.ⓘ Distance from Flange to Web Fillet [k]			+10% -10%

✖Compressive stress is the deformation of a material, leading to a reduction in its volume. It is caused by an externally applied force and is experienced by a material when it is under compression.ⓘ Stress when Concentrated Load is Applied Close to Beam End [f_a]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Webs under Concentrated Loads Formulas PDF PDF Image

Stress when Concentrated Load is Applied Close to Beam End Solution

STEP 0: Pre-Calculation Summary

Formula Used

Compressive Stress = Concentrated Load of Reaction/(Web Thickness*(Bearing or Plate Length+2.5*Distance from Flange to Web Fillet))
f_a = R/(t_w*(N+2.5*k))
This formula uses 5 Variables

Variables Used

Compressive Stress - (Measured in Pascal) - Compressive stress is the deformation of a material, leading to a reduction in its volume. It is caused by an externally applied force and is experienced by a material when it is under compression.
Concentrated Load of Reaction - (Measured in Newton) - Concentrated Load of Reaction is the reaction force that is assumed to act at a single point on the structure.
Web Thickness - (Measured in Meter) - Web Thickness is the thickness of the web section in the member of I section.
Bearing or Plate Length - (Measured in Meter) - Bearing or Plate Length is the length along the beam under which a high concentration of stresses due to concentrated loads is transferred to the supporting structure below.
Distance from Flange to Web Fillet - (Measured in Meter) - The Distance from Flange to Web Fillet is the total distance from the outer face of the flange to the web toe of the fillet.

STEP 1: Convert Input(s) to Base Unit

Concentrated Load of Reaction: 235 Kilonewton --> 235000 Newton (Check conversion here)
Web Thickness: 100 Millimeter --> 0.1 Meter (Check conversion here)
Bearing or Plate Length: 160 Millimeter --> 0.16 Meter (Check conversion here)
Distance from Flange to Web Fillet: 18 Millimeter --> 0.018 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

f_a = R/(t_w*(N+2.5*k)) --> 235000/(0.1*(0.16+2.5*0.018))

Evaluating ... ...

f_a = 11463414.6341463

STEP 3: Convert Result to Output's Unit

11463414.6341463 Pascal -->11.4634146341463 Megapascal (Check conversion here)

FINAL ANSWER

11.4634146341463 ≈ 11.46341 Megapascal <-- Compressive Stress

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Civil » Design of Steel Structures » Webs under Concentrated Loads » Stress when Concentrated Load is Applied Close to Beam End

Credits

Created by Chandana P Dev

NSS College of Engineering (NSSCE), Palakkad

Chandana P Dev has created this Calculator and 500+ more calculators!

Verified by Ishita Goyal

Meerut Institute of Engineering and Technology (MIET), Meerut

Ishita Goyal has verified this Calculator and 2600+ more calculators!

< Webs under Concentrated Loads Calculators

Stress when Concentrated Load is Applied Close to Beam End

LaTeX Go Compressive Stress = Concentrated Load of Reaction/(Web Thickness*(Bearing or Plate Length+2.5*Distance from Flange to Web Fillet))

Stress for Concentrated Load Applied at Distance Larger than Depth of Beam

LaTeX Go Compressive Stress = Concentrated Load of Reaction/(Web Thickness*(Bearing or Plate Length+5*Distance from Flange to Web Fillet))

Length of Bearing when Load applied at Distance Larger than Depth of Beam

LaTeX Go Bearing or Plate Length = (Concentrated Load of Reaction/(Compressive Stress*Web Thickness))-5*Distance from Flange to Web Fillet

Web Thickness for Given Stress

LaTeX Go Web Thickness = Concentrated Load of Reaction/(Compressive Stress*(Bearing or Plate Length+5*Distance from Flange to Web Fillet))

Stress when Concentrated Load is Applied Close to Beam End Formula

LaTeX Go

Compressive Stress = Concentrated Load of Reaction/(Web Thickness*(Bearing or Plate Length+2.5*Distance from Flange to Web Fillet))
f_a = R/(t_w*(N+2.5*k))

What are Columns?

The Column can be defined as a vertical structural member designed to transmit a compressive load. A Column transmits the load from the ceiling/roof slab and beam, including its weight to the foundation. Hence it should be realized that the failure of a column results in the collapse of the entire structure.

What is Web Crippling?

Web Crippling is similar to web buckling, but it happens in the web of the beam when it's subjected to compressive stress. The reaction at support developed due to high concentrated point load on the beam leads to the development of high compressive stresses in the thin web close to the upper flange or lower flange. As a result of this, the thin web may develop a fold at a place close to the flange and this is called web crippling.

How to Calculate Stress when Concentrated Load is Applied Close to Beam End?

Stress when Concentrated Load is Applied Close to Beam End calculator uses Compressive Stress = Concentrated Load of Reaction/(Web Thickness*(Bearing or Plate Length+2.5*Distance from Flange to Web Fillet)) to calculate the Compressive Stress, The Stress when Concentrated Load is Applied Close to Beam End formula is defined as the maximum limit of compressive stress on columns when the concentrated load is acted at a closer distance from the end beam. Compressive Stress is denoted by f_a symbol.

How to calculate Stress when Concentrated Load is Applied Close to Beam End using this online calculator? To use this online calculator for Stress when Concentrated Load is Applied Close to Beam End, enter Concentrated Load of Reaction (R), Web Thickness (t_w), Bearing or Plate Length (N) & Distance from Flange to Web Fillet (k) and hit the calculate button. Here is how the Stress when Concentrated Load is Applied Close to Beam End calculation can be explained with given input values -> 1.1E-5 = 235000/(0.1*(0.16+2.5*0.018)).

FAQ

What is Stress when Concentrated Load is Applied Close to Beam End?

The Stress when Concentrated Load is Applied Close to Beam End formula is defined as the maximum limit of compressive stress on columns when the concentrated load is acted at a closer distance from the end beam and is represented as f_a = R/(t_w*(N+2.5*k)) or Compressive Stress = Concentrated Load of Reaction/(Web Thickness*(Bearing or Plate Length+2.5*Distance from Flange to Web Fillet)). Concentrated Load of Reaction is the reaction force that is assumed to act at a single point on the structure, Web Thickness is the thickness of the web section in the member of I section, Bearing or Plate Length is the length along the beam under which a high concentration of stresses due to concentrated loads is transferred to the supporting structure below & The Distance from Flange to Web Fillet is the total distance from the outer face of the flange to the web toe of the fillet.

How to calculate Stress when Concentrated Load is Applied Close to Beam End?

The Stress when Concentrated Load is Applied Close to Beam End formula is defined as the maximum limit of compressive stress on columns when the concentrated load is acted at a closer distance from the end beam is calculated using Compressive Stress = Concentrated Load of Reaction/(Web Thickness*(Bearing or Plate Length+2.5*Distance from Flange to Web Fillet)). To calculate Stress when Concentrated Load is Applied Close to Beam End, you need Concentrated Load of Reaction (R), Web Thickness (t_w), Bearing or Plate Length (N) & Distance from Flange to Web Fillet (k). With our tool, you need to enter the respective value for Concentrated Load of Reaction, Web Thickness, Bearing or Plate Length & Distance from Flange to Web Fillet and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Compressive Stress?

In this formula, Compressive Stress uses Concentrated Load of Reaction, Web Thickness, Bearing or Plate Length & Distance from Flange to Web Fillet. We can use 1 other way(s) to calculate the same, which is/are as follows -

Compressive Stress = Concentrated Load of Reaction/(Web Thickness*(Bearing or Plate Length+5*Distance from Flange to Web Fillet))

Home

FREE PDFs

🔍 Search