Signal Voltage in High Frequency Response of Source and Emitter Follower Solution

STEP 0: Pre-Calculation Summary
Formula Used
Output Voltage = (Electric Current*Signal Resistance)+Gate to Source Voltage+Threshold Voltage
Vout = (it*Rsig)+Vgs+Vth
This formula uses 5 Variables
Variables Used
Output Voltage - (Measured in Volt) - Output voltage signifies the voltage of the signal after it has been amplified.
Electric Current - (Measured in Ampere) - Electric Current in Conductor 1 is the magnitude of current flowing through conductor 1.
Signal Resistance - (Measured in Ohm) - Signal Resistance is the resistance which is fed with the signal voltage source vs to an Amplifier.
Gate to Source Voltage - (Measured in Volt) - Gate to source voltage of transistor is the voltage that falls across the gate-source terminal of the transistor.
Threshold Voltage - (Measured in Volt) - Threshold voltage of transistor is the minimum gate to source voltage that is needed to create a conducting path between the source and drain terminals.
STEP 1: Convert Input(s) to Base Unit
Electric Current: 19.105 Milliampere --> 0.019105 Ampere (Check conversion ​here)
Signal Resistance: 1.25 Kilohm --> 1250 Ohm (Check conversion ​here)
Gate to Source Voltage: 4 Volt --> 4 Volt No Conversion Required
Threshold Voltage: 0.899 Volt --> 0.899 Volt No Conversion Required
STEP 2: Evaluate Formula
Substituting Input Values in Formula
Vout = (it*Rsig)+Vgs+Vth --> (0.019105*1250)+4+0.899
Evaluating ... ...
Vout = 28.78025
STEP 3: Convert Result to Output's Unit
28.78025 Volt --> No Conversion Required
FINAL ANSWER
28.78025 Volt <-- Output Voltage
(Calculation completed in 00.008 seconds)

Credits

Creator Image
Created by Payal Priya
Birsa Institute of Technology (BIT), Sindri
Payal Priya has created this Calculator and 600+ more calculators!
Verifier Image
Verified by Anshika Arya
National Institute Of Technology (NIT), Hamirpur
Anshika Arya has verified this Calculator and 2500+ more calculators!

Response of Source and Emitter Follower Calculators

Constant 2 of Source Follower Transfer Function
​ LaTeX ​ Go Constant B = (((Gate to Source Capacitance+Gate to Drain Capacitance)*Capacitance+(Gate to Source Capacitance+Gate to Source Capacitance))/(Transconductance*Load Resistance+1))*Signal Resistance*Load Resistance
Signal Voltage in High Frequency Response of Source and Emitter Follower
​ LaTeX ​ Go Output Voltage = (Electric Current*Signal Resistance)+Gate to Source Voltage+Threshold Voltage
Transition Frequency of Source-Follower Transfer Function
​ LaTeX ​ Go Transition Frequency = Transconductance/Gate to Source Capacitance
Dominant Pole-Frequency of Source-Follower
​ LaTeX ​ Go Frequency of Dominant Pole = 1/(2*pi*Constant B)

Multi Stage Amplifiers Calculators

Gain Bandwidth Product
​ LaTeX ​ Go Gain Bandwidth Product = (Transconductance*Load Resistance)/(2*pi*Load Resistance*(Capacitance+Gate to Drain Capacitance))
3-DB Frequency in Design Insight and Trade-Off
​ LaTeX ​ Go 3 dB Frequency = 1/(2*pi*(Capacitance+Gate to Drain Capacitance)*(1/(1/Load Resistance+1/Output Resistance)))
Drain Resistance in Cascode Amplifier
​ LaTeX ​ Go Drain Resistance = 1/(1/Finite Input Resistance+1/Resistance)
Amplifier Gain given Function of Complex Frequency Variable
​ LaTeX ​ Go Amplifier Gain in Mid Band = Mid Band Gain*Gain Factor

Signal Voltage in High Frequency Response of Source and Emitter Follower Formula

​LaTeX ​Go
Output Voltage = (Electric Current*Signal Resistance)+Gate to Source Voltage+Threshold Voltage
Vout = (it*Rsig)+Vgs+Vth

What is emitter-source follower?

The Emitter or Source follower is often called a common Collector or Drain amplifier because the collector or drain is common to both the input and the output. The input impedance is much higher than its output impedance so that a signal source does not have to supply as much power to the input.

How to Calculate Signal Voltage in High Frequency Response of Source and Emitter Follower?

Signal Voltage in High Frequency Response of Source and Emitter Follower calculator uses Output Voltage = (Electric Current*Signal Resistance)+Gate to Source Voltage+Threshold Voltage to calculate the Output Voltage, The Signal voltage in high frequency response of source and emitter follower formula is defined as a voltage or current which conveys information, usually, it means a voltage. The term can be used for any voltage or current in a circuit. Alternating Current (AC) flows one way, then the other way, continually reversing direction. Output Voltage is denoted by Vout symbol.

How to calculate Signal Voltage in High Frequency Response of Source and Emitter Follower using this online calculator? To use this online calculator for Signal Voltage in High Frequency Response of Source and Emitter Follower, enter Electric Current (it), Signal Resistance (Rsig), Gate to Source Voltage (Vgs) & Threshold Voltage (Vth) and hit the calculate button. Here is how the Signal Voltage in High Frequency Response of Source and Emitter Follower calculation can be explained with given input values -> 12.449 = (0.019105*1250)+4+0.899.

FAQ

What is Signal Voltage in High Frequency Response of Source and Emitter Follower?
The Signal voltage in high frequency response of source and emitter follower formula is defined as a voltage or current which conveys information, usually, it means a voltage. The term can be used for any voltage or current in a circuit. Alternating Current (AC) flows one way, then the other way, continually reversing direction and is represented as Vout = (it*Rsig)+Vgs+Vth or Output Voltage = (Electric Current*Signal Resistance)+Gate to Source Voltage+Threshold Voltage. Electric Current in Conductor 1 is the magnitude of current flowing through conductor 1, Signal Resistance is the resistance which is fed with the signal voltage source vs to an Amplifier, Gate to source voltage of transistor is the voltage that falls across the gate-source terminal of the transistor & Threshold voltage of transistor is the minimum gate to source voltage that is needed to create a conducting path between the source and drain terminals.
How to calculate Signal Voltage in High Frequency Response of Source and Emitter Follower?
The Signal voltage in high frequency response of source and emitter follower formula is defined as a voltage or current which conveys information, usually, it means a voltage. The term can be used for any voltage or current in a circuit. Alternating Current (AC) flows one way, then the other way, continually reversing direction is calculated using Output Voltage = (Electric Current*Signal Resistance)+Gate to Source Voltage+Threshold Voltage. To calculate Signal Voltage in High Frequency Response of Source and Emitter Follower, you need Electric Current (it), Signal Resistance (Rsig), Gate to Source Voltage (Vgs) & Threshold Voltage (Vth). With our tool, you need to enter the respective value for Electric Current, Signal Resistance, Gate to Source Voltage & Threshold Voltage and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!