LCM of two numbers

Signal Time Period Calculator

Engineering Chemistry Financial Health More >>

↳

Electronics Chemical Engineering Civil Electrical More >>

⤿

Digital Communication Amplifiers Analog Communications Analog Electronics More >>

⤿

Modulation Techniques Modulation Parameters

✖Rolloff factor is a parameter used in signal processing and telecommunications to describe the rate at which the magnitude or power of a signal decreases outside the desired bandwidth.ⓘ Rolloff Factor [α]			+10% -10%
✖Bandwidth of raised cosine filter is defined as the most commonly defined as the width of the non-zero frequency-positive portion of its spectrum.ⓘ Bandwidth of Raised Cosine Filter [f_b]			+10% -10%

✖Signal Time Period refers to the time it takes for a periodic signal to complete one full cycle. It is the duration between successive occurrences of the same point or phase in the signal waveform.ⓘ Signal Time Period [T]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Digital Communication Formulas PDF PDF Image

Signal Time Period Solution

STEP 0: Pre-Calculation Summary

Formula Used

Signal Time Period = (1+Rolloff Factor)/(2*Bandwidth of Raised Cosine Filter)
T = (1+α)/(2*f_b)
This formula uses 3 Variables

Variables Used

Signal Time Period - (Measured in Second) - Signal Time Period refers to the time it takes for a periodic signal to complete one full cycle. It is the duration between successive occurrences of the same point or phase in the signal waveform.
Rolloff Factor - Rolloff factor is a parameter used in signal processing and telecommunications to describe the rate at which the magnitude or power of a signal decreases outside the desired bandwidth.
Bandwidth of Raised Cosine Filter - (Measured in Bit Per Second) - Bandwidth of raised cosine filter is defined as the most commonly defined as the width of the non-zero frequency-positive portion of its spectrum.

STEP 1: Convert Input(s) to Base Unit

Rolloff Factor: 0.5 --> No Conversion Required
Bandwidth of Raised Cosine Filter: 107.14 Kilobit per Second --> 107140 Bit Per Second (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

T = (1+α)/(2*f_b) --> (1+0.5)/(2*107140)

Evaluating ... ...

T = 7.00018667164458E-06

STEP 3: Convert Result to Output's Unit

7.00018667164458E-06 Second -->7.00018667164458 Microsecond (Check conversion here)

FINAL ANSWER

7.00018667164458 ≈ 7.000187 Microsecond <-- Signal Time Period

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electronics » Digital Communication » Modulation Techniques » Signal Time Period

Credits

Created by Akshada Kulkarni

National Institute of Information Technology (NIIT), Neemrana

Akshada Kulkarni has created this Calculator and 500+ more calculators!

Verified by Suman Ray Pramanik

Indian Institute of Technology (IIT), Kanpur

Suman Ray Pramanik has verified this Calculator and 100+ more calculators!

< Modulation Techniques Calculators

Bandwidth of FSK

LaTeX Go Bandwidth of FSK = Bit Rate*(1+Rolloff Factor)+(2*Difference in Frequency)

Bandwidth of Raised Cosine Filter

LaTeX Go Bandwidth of Raised Cosine Filter = (1+Rolloff Factor)/(2*Signal Time Period)

Symbol Time

LaTeX Go Symbol Time = Bit Rate/Bits Conveyed Per Symbol

Baud Rate

LaTeX Go Baud Rate = Bit Rate/Number of Bits

Signal Time Period Formula

LaTeX Go

Signal Time Period = (1+Rolloff Factor)/(2*Bandwidth of Raised Cosine Filter)
T = (1+α)/(2*f_b)

What are the advantages of FSK?

It has better noise immunity than ASK method, so the probability of error-free reception of data is high. Easy to decode. Operate in virtually any wires available. FSK transmitter, as well as FSK receiver implementations, are simple for low data rate application. Error arises in a digital communication signal due to Inter Signal Interference and gaussian noise. This is calculated in a closed form using the error function "erfc".

How to Calculate Signal Time Period?

Signal Time Period calculator uses Signal Time Period = (1+Rolloff Factor)/(2*Bandwidth of Raised Cosine Filter) to calculate the Signal Time Period, Signal Time Period refers to the time it takes for a periodic signal to complete one full cycle. It is the duration between successive occurrences of the same point or phase in the signal waveform. Signal Time Period is denoted by T symbol.

How to calculate Signal Time Period using this online calculator? To use this online calculator for Signal Time Period, enter Rolloff Factor (α) & Bandwidth of Raised Cosine Filter (f_b) and hit the calculate button. Here is how the Signal Time Period calculation can be explained with given input values -> 7E+6 = (1+0.5)/(2*107140).

FAQ

What is Signal Time Period?

Signal Time Period refers to the time it takes for a periodic signal to complete one full cycle. It is the duration between successive occurrences of the same point or phase in the signal waveform and is represented as T = (1+α)/(2*f_b) or Signal Time Period = (1+Rolloff Factor)/(2*Bandwidth of Raised Cosine Filter). Rolloff factor is a parameter used in signal processing and telecommunications to describe the rate at which the magnitude or power of a signal decreases outside the desired bandwidth & Bandwidth of raised cosine filter is defined as the most commonly defined as the width of the non-zero frequency-positive portion of its spectrum.

How to calculate Signal Time Period?

Signal Time Period refers to the time it takes for a periodic signal to complete one full cycle. It is the duration between successive occurrences of the same point or phase in the signal waveform is calculated using Signal Time Period = (1+Rolloff Factor)/(2*Bandwidth of Raised Cosine Filter). To calculate Signal Time Period, you need Rolloff Factor (α) & Bandwidth of Raised Cosine Filter (f_b). With our tool, you need to enter the respective value for Rolloff Factor & Bandwidth of Raised Cosine Filter and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search