Signal Current in Emitter given Input Signal Solution

STEP 0: Pre-Calculation Summary
Formula Used
Signal Current in Emitter = Fundamental Component Voltage/Emitter Resistance
ise = Vfc/Re
This formula uses 3 Variables
Variables Used
Signal Current in Emitter - (Measured in Ampere) - Signal current in emitter is the current in the amplified output current of a transistor.
Fundamental Component Voltage - (Measured in Volt) - Fundamental component voltage is the first harmonic of the voltage in the harmonic analysis of the square wave of voltage in an inverter based circuit.
Emitter Resistance - (Measured in Ohm) - Emitter Resistance is a dynamic resistance of the emitter-base junction diode of a transistor.
STEP 1: Convert Input(s) to Base Unit
Fundamental Component Voltage: 5 Volt --> 5 Volt No Conversion Required
Emitter Resistance: 0.067 Kilohm --> 67 Ohm (Check conversion ​here)
STEP 2: Evaluate Formula
Substituting Input Values in Formula
ise = Vfc/Re --> 5/67
Evaluating ... ...
ise = 0.0746268656716418
STEP 3: Convert Result to Output's Unit
0.0746268656716418 Ampere -->74.6268656716418 Milliampere (Check conversion ​here)
FINAL ANSWER
74.6268656716418 74.62687 Milliampere <-- Signal Current in Emitter
(Calculation completed in 00.020 seconds)

Credits

Creator Image
Created by Payal Priya
Birsa Institute of Technology (BIT), Sindri
Payal Priya has created this Calculator and 600+ more calculators!
Verifier Image
Verified by Anshika Arya
National Institute Of Technology (NIT), Hamirpur
Anshika Arya has verified this Calculator and 2500+ more calculators!

Transistor Amplifier Characteristics Calculators

Current Flowing through Induced Channel in Transistor given Oxide Voltage
​ Go Output Current = (Mobility of Electron*Oxide Capacitance*(Width of Channel/Length of Channel)*(Voltage across Oxide-Threshold Voltage))*Saturation Voltage between Drain and Source
Current Entering Drain Terminal of MOSFET at Saturation
​ Go Saturation Drain Current = 1/2*Process Transconductance Parameter*(Width of Channel/Length of Channel)*(Effective Voltage)^2
Total Instantaneous Drain Voltage
​ Go Total Instantaneous Drain Voltage = Fundamental Component Voltage-Drain Resistance*Drain Current
Input Voltage in Transistor
​ Go Fundamental Component Voltage = Drain Resistance*Drain Current-Total Instantaneous Drain Voltage

CV Actions of Common Stage Amplifiers Calculators

Input Resistance of Common Emitter Amplifier
​ Go Input Resistance = (1/Base Resistance+1/Base Resistance 2+1/Small Signal Input Resistance)^-1
Input Impedance of Common-Base Amplifier
​ Go Input Impedance = (1/Emitter Resistance+1/Small Signal Input Resistance)^(-1)
Fundamental Voltage in Common-Emitter Amplifier
​ Go Fundamental Component Voltage = Input Resistance*Base Current
Emitter Current of Common-Base Amplifier
​ Go Emitter Current = Input Voltage/Emitter Resistance

Signal Current in Emitter given Input Signal Formula

Signal Current in Emitter = Fundamental Component Voltage/Emitter Resistance
ise = Vfc/Re

What is emitter current?

The emitter current, Ie, of a transistor is the amplified output current of a bipolar junction transistor. There are several ways to find the emitter current, Ie, of a transistor.

How to Calculate Signal Current in Emitter given Input Signal?

Signal Current in Emitter given Input Signal calculator uses Signal Current in Emitter = Fundamental Component Voltage/Emitter Resistance to calculate the Signal Current in Emitter, The Signal Current in Emitter given Input Signal is the current flowing from the emitter to the ground. Signal Current in Emitter is denoted by ise symbol.

How to calculate Signal Current in Emitter given Input Signal using this online calculator? To use this online calculator for Signal Current in Emitter given Input Signal, enter Fundamental Component Voltage (Vfc) & Emitter Resistance (Re) and hit the calculate button. Here is how the Signal Current in Emitter given Input Signal calculation can be explained with given input values -> 74626.87 = 5/67.

FAQ

What is Signal Current in Emitter given Input Signal?
The Signal Current in Emitter given Input Signal is the current flowing from the emitter to the ground and is represented as ise = Vfc/Re or Signal Current in Emitter = Fundamental Component Voltage/Emitter Resistance. Fundamental component voltage is the first harmonic of the voltage in the harmonic analysis of the square wave of voltage in an inverter based circuit & Emitter Resistance is a dynamic resistance of the emitter-base junction diode of a transistor.
How to calculate Signal Current in Emitter given Input Signal?
The Signal Current in Emitter given Input Signal is the current flowing from the emitter to the ground is calculated using Signal Current in Emitter = Fundamental Component Voltage/Emitter Resistance. To calculate Signal Current in Emitter given Input Signal, you need Fundamental Component Voltage (Vfc) & Emitter Resistance (Re). With our tool, you need to enter the respective value for Fundamental Component Voltage & Emitter Resistance and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!