LCM of three numbers

Series Resistance in N-type Calculator

Engineering Chemistry Financial Health More >>

↳

Electronics Chemical Engineering Civil Electrical More >>

⤿

Solid State Devices Amplifiers Analog Communications Analog Electronics More >>

⤿

SSD Junction Electrons and Holes Energy Band and Charge Carrier Semiconductor Carriers

✖Source Voltage is the difference in electric potential between two points, which is defined as the work needed per unit of charge to move a test charge between the two points.ⓘ Source Voltage [V]			+10% -10%
✖Junction voltage is the portion of the channel in a metal oxide field-effect transistor in which there are no charge carriers.ⓘ Junction Voltage [V_j]			+10% -10%
✖Electric Current is the time rate of flow of charge through a cross sectional area in a solid state device.ⓘ Electric Current [I]			+10% -10%
✖Series Resistance in p Junction is defined as the total resistance in the series inside a circuit at p-junction.ⓘ Series Resistance in P Junction [R_se(p)]			+10% -10%

✖Series Resistance in n Junction is defined as the total resistance in the series inside a circuit at n-junction.ⓘ Series Resistance in N-type [R_se(n)]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download SSD Junction Formulas PDF PDF Image

Series Resistance in N-type Solution

STEP 0: Pre-Calculation Summary

Formula Used

Series Resistance in N Junction = ((Source Voltage-Junction Voltage)/Electric Current)-Series Resistance in P Junction
R_se(n) = ((V-V_j)/I)-R_se(p)
This formula uses 5 Variables

Variables Used

Series Resistance in N Junction - (Measured in Ohm) - Series Resistance in n Junction is defined as the total resistance in the series inside a circuit at n-junction.
Source Voltage - (Measured in Volt) - Source Voltage is the difference in electric potential between two points, which is defined as the work needed per unit of charge to move a test charge between the two points.
Junction Voltage - (Measured in Volt) - Junction voltage is the portion of the channel in a metal oxide field-effect transistor in which there are no charge carriers.
Electric Current - (Measured in Ampere) - Electric Current is the time rate of flow of charge through a cross sectional area in a solid state device.
Series Resistance in P Junction - (Measured in Ohm) - Series Resistance in p Junction is defined as the total resistance in the series inside a circuit at p-junction.

STEP 1: Convert Input(s) to Base Unit

Source Voltage: 120 Volt --> 120 Volt No Conversion Required
Junction Voltage: 119.9 Volt --> 119.9 Volt No Conversion Required
Electric Current: 0.2 Milliampere --> 0.0002 Ampere (Check conversion here)
Series Resistance in P Junction: 23.3 Ohm --> 23.3 Ohm No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

R_se(n) = ((V-V_j)/I)-R_se(p) --> ((120-119.9)/0.0002)-23.3

Evaluating ... ...

R_se(n) = 476.699999999972

STEP 3: Convert Result to Output's Unit

476.699999999972 Ohm --> No Conversion Required

FINAL ANSWER

476.699999999972 ≈ 476.7 Ohm <-- Series Resistance in N Junction

(Calculation completed in 00.008 seconds)

You are here -

Home » Engineering » Electronics » Solid State Devices » SSD Junction » Series Resistance in N-type

Credits

Created by Shobhit Dimri

Bipin Tripathi Kumaon Institute of Technology (BTKIT), Dwarahat

Shobhit Dimri has created this Calculator and 900+ more calculators!

Verified by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has verified this Calculator and 1900+ more calculators!

< SSD Junction Calculators

Junction Capacitance

LaTeX Go Junction Capacitance = (Junction Area/2)*sqrt((2*[Charge-e]*Constant Length Offset*Doping Concentration of Base)/(Source Voltage-Source Voltage 1))

Series Resistance in P-type

LaTeX Go Series Resistance in P Junction = ((Source Voltage-Junction Voltage)/Electric Current)-Series Resistance in N Junction

Junction Voltage

LaTeX Go Junction Voltage = Source Voltage-(Series Resistance in P Junction+Series Resistance in N Junction)*Electric Current

N-Type Width

LaTeX Go Charge Penetration N-type = Total Acceptor Charge/(Junction Area*Acceptor Concentration*[Charge-e])

Series Resistance in N-type Formula

LaTeX Go

Series Resistance in N Junction = ((Source Voltage-Junction Voltage)/Electric Current)-Series Resistance in P Junction
R_se(n) = ((V-V_j)/I)-R_se(p)

What happens in series resistance?

In a series resistor network the individual resistors add together to give an equivalent resistance, ( RT ) of the series combination. The resistors in a series circuit can be interchanged without affecting the total resistance, current, or power to each resistor or the circuit.

How to Calculate Series Resistance in N-type?

Series Resistance in N-type calculator uses Series Resistance in N Junction = ((Source Voltage-Junction Voltage)/Electric Current)-Series Resistance in P Junction to calculate the Series Resistance in N Junction, The Series Resistance in N-type formula is defined as the total resistance in the series inside a a circuit at n-junction. Series Resistance in N Junction is denoted by R_se(n) symbol.

How to calculate Series Resistance in N-type using this online calculator? To use this online calculator for Series Resistance in N-type, enter Source Voltage (V), Junction Voltage (V_j), Electric Current (I) & Series Resistance in P Junction (R_se(p)) and hit the calculate button. Here is how the Series Resistance in N-type calculation can be explained with given input values -> 476.7 = ((120-119.9)/0.0002)-23.3.

FAQ

What is Series Resistance in N-type?

The Series Resistance in N-type formula is defined as the total resistance in the series inside a a circuit at n-junction and is represented as R_se(n) = ((V-V_j)/I)-R_se(p) or Series Resistance in N Junction = ((Source Voltage-Junction Voltage)/Electric Current)-Series Resistance in P Junction. Source Voltage is the difference in electric potential between two points, which is defined as the work needed per unit of charge to move a test charge between the two points, Junction voltage is the portion of the channel in a metal oxide field-effect transistor in which there are no charge carriers, Electric Current is the time rate of flow of charge through a cross sectional area in a solid state device & Series Resistance in p Junction is defined as the total resistance in the series inside a circuit at p-junction.

How to calculate Series Resistance in N-type?

The Series Resistance in N-type formula is defined as the total resistance in the series inside a a circuit at n-junction is calculated using Series Resistance in N Junction = ((Source Voltage-Junction Voltage)/Electric Current)-Series Resistance in P Junction. To calculate Series Resistance in N-type, you need Source Voltage (V), Junction Voltage (V_j), Electric Current (I) & Series Resistance in P Junction (R_se(p)). With our tool, you need to enter the respective value for Source Voltage, Junction Voltage, Electric Current & Series Resistance in P Junction and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search