RMS Voltage using Volume of Conductor Material(1 Phase 3 Wire US) Calculator

✖Resistivity is the measure of how strongly a material opposes the flow of current through them.ⓘ Resistivity [ρ]			+10% -10%
✖Power Transmitted is the amount of power that is transferred from its place of generation to a location where it is applied to perform useful work.ⓘ Power Transmitted [P]			+10% -10%
✖Length of Underground AC Wire is the total length of the wire from one end to other end.ⓘ Length of Underground AC Wire [L]			+10% -10%
✖Line Losses is defined as the total losses occurring in an Underground AC line when in use.ⓘ Line Losses [P_loss]			+10% -10%
✖Volume Of Conductor the 3-dimensional space enclosed by a conductor material.ⓘ Volume Of Conductor [V]			+10% -10%
✖Phase Difference is defined as the difference between the phasor of apparent and real power (in degrees) or between voltage and current in an ac circuit.ⓘ Phase Difference [Φ]			+10% -10%

✖Root Mean Square Voltage is the square root of the time average of the voltage squared.ⓘ RMS Voltage using Volume of Conductor Material(1 Phase 3 Wire US) [V_rms]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Power System Formula PDF PDF Image

RMS Voltage using Volume of Conductor Material(1 Phase 3 Wire US) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Root Mean Square Voltage = sqrt(5*Resistivity*((Power Transmitted*Length of Underground AC Wire)^2)/(Line Losses*Volume Of Conductor*((cos(Phase Difference))^2)))
V_rms = sqrt(5*ρ*((P*L)^2)/(P_loss*V*((cos(Φ))^2)))
This formula uses 2 Functions, 7 Variables

Functions Used

cos - Cosine of an angle is the ratio of the side adjacent to the angle to the hypotenuse of the triangle., cos(Angle)
sqrt - A square root function is a function that takes a non-negative number as an input and returns the square root of the given input number., sqrt(Number)

Variables Used

Root Mean Square Voltage - (Measured in Volt) - Root Mean Square Voltage is the square root of the time average of the voltage squared.
Resistivity - (Measured in Ohm Meter) - Resistivity is the measure of how strongly a material opposes the flow of current through them.
Power Transmitted - (Measured in Watt) - Power Transmitted is the amount of power that is transferred from its place of generation to a location where it is applied to perform useful work.
Length of Underground AC Wire - (Measured in Meter) - Length of Underground AC Wire is the total length of the wire from one end to other end.
Line Losses - (Measured in Watt) - Line Losses is defined as the total losses occurring in an Underground AC line when in use.
Volume Of Conductor - (Measured in Cubic Meter) - Volume Of Conductor the 3-dimensional space enclosed by a conductor material.
Phase Difference - (Measured in Radian) - Phase Difference is defined as the difference between the phasor of apparent and real power (in degrees) or between voltage and current in an ac circuit.

STEP 1: Convert Input(s) to Base Unit

Resistivity: 1.7E-05 Ohm Meter --> 1.7E-05 Ohm Meter No Conversion Required
Power Transmitted: 300 Watt --> 300 Watt No Conversion Required
Length of Underground AC Wire: 24 Meter --> 24 Meter No Conversion Required
Line Losses: 2.67 Watt --> 2.67 Watt No Conversion Required
Volume Of Conductor: 60 Cubic Meter --> 60 Cubic Meter No Conversion Required
Phase Difference: 30 Degree --> 0.5235987755982 Radian (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

V_rms = sqrt(5*ρ*((P*L)^2)/(P_loss*V*((cos(Φ))^2))) --> sqrt(5*1.7E-05*((300*24)^2)/(2.67*60*((cos(0.5235987755982))^2)))

Evaluating ... ...

V_rms = 6.05591919557806

STEP 3: Convert Result to Output's Unit

6.05591919557806 Volt --> No Conversion Required

FINAL ANSWER

6.05591919557806 ≈ 6.055919 Volt <-- Root Mean Square Voltage

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Power System » Underground AC Supply » 1 Φ 3 Wire System » Current and Voltage » RMS Voltage using Volume of Conductor Material(1 Phase 3 Wire US)

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Shobhit Dimri

Bipin Tripathi Kumaon Institute of Technology (BTKIT), Dwarahat

Shobhit Dimri has verified this Calculator and 100+ more calculators!

< Current and Voltage Calculators

Maximum Voltage using Volume of Conductor Material(1 Phase 3 Wire US)

LaTeX Go Maximum Voltage Underground AC = sqrt(10*Resistivity*(Power Transmitted*Length of Underground AC Wire)^2/(Line Losses*Volume Of Conductor*(cos(Phase Difference))^2))

RMS Voltage using Volume of Conductor Material(1 Phase 3 Wire US)

LaTeX Go Root Mean Square Voltage = sqrt(5*Resistivity*((Power Transmitted*Length of Underground AC Wire)^2)/(Line Losses*Volume Of Conductor*((cos(Phase Difference))^2)))

Maximum Voltage using Load Current (1 Phase 3 Wire US)

LaTeX Go Maximum Voltage Underground AC = sqrt(2)*Power Transmitted/(cos(Phase Difference)*Current Underground AC)

RMS Voltage using Load Current (1 Phase 3 Wire US)

LaTeX Go Root Mean Square Voltage = sqrt(2)*Power Transmitted/(cos(Phase Difference)*Current Underground AC)

RMS Voltage using Volume of Conductor Material(1 Phase 3 Wire US) Formula

LaTeX Go

What is the value of maximum voltage and volume of conductor material in 1-phase 3-wire system?

The volume of conductor material required in this system is 2.5/cos²θ times that of 2-wire d.c.system with the one conductor earthed. The maximum voltage between conductors is v_m so that r.m.s. value of voltage between them is v_m/√2.

How to Calculate RMS Voltage using Volume of Conductor Material(1 Phase 3 Wire US)?

RMS Voltage using Volume of Conductor Material(1 Phase 3 Wire US) calculator uses Root Mean Square Voltage = sqrt(5*Resistivity*((Power Transmitted*Length of Underground AC Wire)^2)/(Line Losses*Volume Of Conductor*((cos(Phase Difference))^2))) to calculate the Root Mean Square Voltage, The RMS Voltage using Volume of Conductor Material(1 phase 3 wire US) formula is defined as the square root of the time average of the voltage squared. Root Mean Square Voltage is denoted by V_rms symbol.

How to calculate RMS Voltage using Volume of Conductor Material(1 Phase 3 Wire US) using this online calculator? To use this online calculator for RMS Voltage using Volume of Conductor Material(1 Phase 3 Wire US), enter Resistivity (ρ), Power Transmitted (P), Length of Underground AC Wire (L), Line Losses (P_loss), Volume Of Conductor (V) & Phase Difference (Φ) and hit the calculate button. Here is how the RMS Voltage using Volume of Conductor Material(1 Phase 3 Wire US) calculation can be explained with given input values -> 6.055919 = sqrt(5*1.7E-05*((300*24)^2)/(2.67*60*((cos(0.5235987755982))^2))).

FAQ

What is RMS Voltage using Volume of Conductor Material(1 Phase 3 Wire US)?

The RMS Voltage using Volume of Conductor Material(1 phase 3 wire US) formula is defined as the square root of the time average of the voltage squared and is represented as V_rms = sqrt(5*ρ*((P*L)^2)/(P_loss*V*((cos(Φ))^2))) or Root Mean Square Voltage = sqrt(5*Resistivity*((Power Transmitted*Length of Underground AC Wire)^2)/(Line Losses*Volume Of Conductor*((cos(Phase Difference))^2))). Resistivity is the measure of how strongly a material opposes the flow of current through them, Power Transmitted is the amount of power that is transferred from its place of generation to a location where it is applied to perform useful work, Length of Underground AC Wire is the total length of the wire from one end to other end, Line Losses is defined as the total losses occurring in an Underground AC line when in use, Volume Of Conductor the 3-dimensional space enclosed by a conductor material & Phase Difference is defined as the difference between the phasor of apparent and real power (in degrees) or between voltage and current in an ac circuit.

How to calculate RMS Voltage using Volume of Conductor Material(1 Phase 3 Wire US)?

The RMS Voltage using Volume of Conductor Material(1 phase 3 wire US) formula is defined as the square root of the time average of the voltage squared is calculated using Root Mean Square Voltage = sqrt(5*Resistivity*((Power Transmitted*Length of Underground AC Wire)^2)/(Line Losses*Volume Of Conductor*((cos(Phase Difference))^2))). To calculate RMS Voltage using Volume of Conductor Material(1 Phase 3 Wire US), you need Resistivity (ρ), Power Transmitted (P), Length of Underground AC Wire (L), Line Losses (P_loss), Volume Of Conductor (V) & Phase Difference (Φ). With our tool, you need to enter the respective value for Resistivity, Power Transmitted, Length of Underground AC Wire, Line Losses, Volume Of Conductor & Phase Difference and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Root Mean Square Voltage?

In this formula, Root Mean Square Voltage uses Resistivity, Power Transmitted, Length of Underground AC Wire, Line Losses, Volume Of Conductor & Phase Difference. We can use 3 other way(s) to calculate the same, which is/are as follows -

Root Mean Square Voltage = sqrt(2)*Power Transmitted/(cos(Phase Difference)*Current Underground AC)
Root Mean Square Voltage = (Power Transmitted/cos(Phase Difference))*sqrt(2*Resistivity*Length of Underground AC Wire/(Line Losses*Area of Underground AC Wire))
Root Mean Square Voltage = (Power Transmitted/cos(Phase Difference))*sqrt(2*Resistance Underground AC/(Line Losses))

Home

FREE PDFs

🔍 Search