RMS Voltage using Area of X-Section(Single Phase Two Wire OS) Calculator

✖Length of Overhead AC Wire is the total length of the wire from one end to other end.ⓘ Length of Overhead AC Wire [L]			+10% -10%
✖Resistivity is the measure of how strongly a material opposes the flow of current through them.ⓘ Resistivity [ρ]			+10% -10%
✖Power Transmitted is defined as the product of current and voltage phasor in a overhead ac line at the receiving end.ⓘ Power Transmitted [P]			+10% -10%
✖Area of Overhead AC Wire is defined as the cross-sectional area of the wire of an AC supply system.ⓘ Area of Overhead AC Wire [A]			+10% -10%
✖Line Losses is defined as the total losses occurring in an Overhead AC line when in use.ⓘ Line Losses [P_loss]			+10% -10%
✖Phase Difference is defined as the difference between the phasor of apparent and real power (in degrees) or between voltage and current in an ac circuit.ⓘ Phase Difference [Φ]			+10% -10%

✖Root Mean Square Voltage is the square root of the time average of the voltage squared.ⓘ RMS Voltage using Area of X-Section(Single Phase Two Wire OS) [V_rms]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Power System Formula PDF PDF Image

RMS Voltage using Area of X-Section(Single Phase Two Wire OS) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Root Mean Square Voltage = sqrt((2*Length of Overhead AC Wire*Resistivity*Power Transmitted^2)/(Area of Overhead AC Wire*Line Losses*cos(Phase Difference)^2))
V_rms = sqrt((2*L*ρ*P^2)/(A*P_loss*cos(Φ)^2))
This formula uses 2 Functions, 7 Variables

Functions Used

cos - Cosine of an angle is the ratio of the side adjacent to the angle to the hypotenuse of the triangle., cos(Angle)
sqrt - A square root function is a function that takes a non-negative number as an input and returns the square root of the given input number., sqrt(Number)

Variables Used

Root Mean Square Voltage - (Measured in Volt) - Root Mean Square Voltage is the square root of the time average of the voltage squared.
Length of Overhead AC Wire - (Measured in Meter) - Length of Overhead AC Wire is the total length of the wire from one end to other end.
Resistivity - (Measured in Ohm Meter) - Resistivity is the measure of how strongly a material opposes the flow of current through them.
Power Transmitted - (Measured in Watt) - Power Transmitted is defined as the product of current and voltage phasor in a overhead ac line at the receiving end.
Area of Overhead AC Wire - (Measured in Square Meter) - Area of Overhead AC Wire is defined as the cross-sectional area of the wire of an AC supply system.
Line Losses - (Measured in Watt) - Line Losses is defined as the total losses occurring in an Overhead AC line when in use.
Phase Difference - (Measured in Radian) - Phase Difference is defined as the difference between the phasor of apparent and real power (in degrees) or between voltage and current in an ac circuit.

STEP 1: Convert Input(s) to Base Unit

Length of Overhead AC Wire: 10.63 Meter --> 10.63 Meter No Conversion Required
Resistivity: 1.7E-05 Ohm Meter --> 1.7E-05 Ohm Meter No Conversion Required
Power Transmitted: 890 Watt --> 890 Watt No Conversion Required
Area of Overhead AC Wire: 0.79 Square Meter --> 0.79 Square Meter No Conversion Required
Line Losses: 8.23 Watt --> 8.23 Watt No Conversion Required
Phase Difference: 30 Degree --> 0.5235987755982 Radian (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

V_rms = sqrt((2*L*ρ*P^2)/(A*P_loss*cos(Φ)^2)) --> sqrt((2*10.63*1.7E-05*890^2)/(0.79*8.23*cos(0.5235987755982)^2))

Evaluating ... ...

V_rms = 7.66217386495464

STEP 3: Convert Result to Output's Unit

7.66217386495464 Volt --> No Conversion Required

FINAL ANSWER

7.66217386495464 ≈ 7.662174 Volt <-- Root Mean Square Voltage

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Power System » Overhead AC Supply » 1 2 Wire System » Current and Voltage » RMS Voltage using Area of X-Section(Single Phase Two Wire OS)

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Kethavath Srinath

Osmania University (OU), Hyderabad

Kethavath Srinath has verified this Calculator and 1200+ more calculators!

< Current and Voltage Calculators

Maximum Voltage using Area of X-Section(Single Phase Two Wire OS)

LaTeX Go Maximum Voltage Overhead AC = sqrt((4*Length of Overhead AC Wire*Resistivity*Power Transmitted^2)/(Area of Overhead AC Wire*Line Losses*cos(Phase Difference)^2))

RMS Voltage using Area of X-Section(Single Phase Two Wire OS)

LaTeX Go Root Mean Square Voltage = sqrt((2*Length of Overhead AC Wire*Resistivity*Power Transmitted^2)/(Area of Overhead AC Wire*Line Losses*cos(Phase Difference)^2))

Load Current using Area of X-Section(Single Phase Two Wire OS)

LaTeX Go Current Overhead AC = sqrt((Area of Overhead AC Wire*Line Losses)/(Resistivity*Length of Overhead AC Wire))

Load Current(Single Phase Two Wire OS)

LaTeX Go Current Overhead AC = (sqrt(2)*Power Transmitted)/(Voltage Overhead AC*cos(Phase Difference))

RMS Voltage using Area of X-Section(Single Phase Two Wire OS) Formula

LaTeX Go

What is the value of maximum voltage and volume of conductor material in 1-phase 2-wire system?

The volume of conductor material required in this system is 2/cos²θ times that of 2-wire d.c.system with the one conductor earthed. The maximum voltage between conductors is v_m so that r.m.s. value of voltage between them is v_m/√2.

How to Calculate RMS Voltage using Area of X-Section(Single Phase Two Wire OS)?

RMS Voltage using Area of X-Section(Single Phase Two Wire OS) calculator uses Root Mean Square Voltage = sqrt((2*Length of Overhead AC Wire*Resistivity*Power Transmitted^2)/(Area of Overhead AC Wire*Line Losses*cos(Phase Difference)^2)) to calculate the Root Mean Square Voltage, The RMS Voltage using Area of X-section(single Phase two Wire OS) formula is defined as the square root of the time average of the voltage squared. Root Mean Square Voltage is denoted by V_rms symbol.

How to calculate RMS Voltage using Area of X-Section(Single Phase Two Wire OS) using this online calculator? To use this online calculator for RMS Voltage using Area of X-Section(Single Phase Two Wire OS), enter Length of Overhead AC Wire (L), Resistivity (ρ), Power Transmitted (P), Area of Overhead AC Wire (A), Line Losses (P_loss) & Phase Difference (Φ) and hit the calculate button. Here is how the RMS Voltage using Area of X-Section(Single Phase Two Wire OS) calculation can be explained with given input values -> 7.662174 = sqrt((2*10.63*1.7E-05*890^2)/(0.79*8.23*cos(0.5235987755982)^2)).

FAQ

What is RMS Voltage using Area of X-Section(Single Phase Two Wire OS)?

The RMS Voltage using Area of X-section(single Phase two Wire OS) formula is defined as the square root of the time average of the voltage squared and is represented as V_rms = sqrt((2*L*ρ*P^2)/(A*P_loss*cos(Φ)^2)) or Root Mean Square Voltage = sqrt((2*Length of Overhead AC Wire*Resistivity*Power Transmitted^2)/(Area of Overhead AC Wire*Line Losses*cos(Phase Difference)^2)). Length of Overhead AC Wire is the total length of the wire from one end to other end, Resistivity is the measure of how strongly a material opposes the flow of current through them, Power Transmitted is defined as the product of current and voltage phasor in a overhead ac line at the receiving end, Area of Overhead AC Wire is defined as the cross-sectional area of the wire of an AC supply system, Line Losses is defined as the total losses occurring in an Overhead AC line when in use & Phase Difference is defined as the difference between the phasor of apparent and real power (in degrees) or between voltage and current in an ac circuit.

How to calculate RMS Voltage using Area of X-Section(Single Phase Two Wire OS)?

The RMS Voltage using Area of X-section(single Phase two Wire OS) formula is defined as the square root of the time average of the voltage squared is calculated using Root Mean Square Voltage = sqrt((2*Length of Overhead AC Wire*Resistivity*Power Transmitted^2)/(Area of Overhead AC Wire*Line Losses*cos(Phase Difference)^2)). To calculate RMS Voltage using Area of X-Section(Single Phase Two Wire OS), you need Length of Overhead AC Wire (L), Resistivity (ρ), Power Transmitted (P), Area of Overhead AC Wire (A), Line Losses (P_loss) & Phase Difference (Φ). With our tool, you need to enter the respective value for Length of Overhead AC Wire, Resistivity, Power Transmitted, Area of Overhead AC Wire, Line Losses & Phase Difference and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Root Mean Square Voltage?

In this formula, Root Mean Square Voltage uses Length of Overhead AC Wire, Resistivity, Power Transmitted, Area of Overhead AC Wire, Line Losses & Phase Difference. We can use 1 other way(s) to calculate the same, which is/are as follows -

Root Mean Square Voltage = Power Transmitted/(Current Overhead AC*cos(Phase Difference))

Home

FREE PDFs

🔍 Search