Required Thickness for Jacket Closer Member with Jacket Width Calculator

✖Jacket Width is the measurement or extent of something from side to side.ⓘ Jacket Width [w_j]			+10% -10%
✖Design Jacket Pressure refers to a type of pressure vessel designed to withstand high pressures and temperatures, typically used for containing gases or liquids under extreme conditions.ⓘ Design Jacket Pressure [p_j]			+10% -10%
✖Allowable Stress for Jacket Material at Design Temperature is defined as the material failure stress divided by a factor of safety greater than one.ⓘ Allowable Stress for Jacket Material [f_j]			+10% -10%

✖Required Thickness for Jacket Closer Member will be determined by the maximum allowable stress in the material, the design pressure and temperature.ⓘ Required Thickness for Jacket Closer Member with Jacket Width [t_rc]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Jacketed Reaction Vessel Formulas PDF PDF Image

Required Thickness for Jacket Closer Member with Jacket Width Solution

STEP 0: Pre-Calculation Summary

Formula Used

Required Thickness for Jacket Closer Member = 0.886*Jacket Width*sqrt(Design Jacket Pressure/Allowable Stress for Jacket Material)
t_rc = 0.886*w_j*sqrt(p_j/f_j)
This formula uses 1 Functions, 4 Variables

Functions Used

sqrt - A square root function is a function that takes a non-negative number as an input and returns the square root of the given input number., sqrt(Number)

Variables Used

Required Thickness for Jacket Closer Member - (Measured in Millimeter) - Required Thickness for Jacket Closer Member will be determined by the maximum allowable stress in the material, the design pressure and temperature.
Jacket Width - (Measured in Millimeter) - Jacket Width is the measurement or extent of something from side to side.
Design Jacket Pressure - (Measured in Newton per Square Millimeter) - Design Jacket Pressure refers to a type of pressure vessel designed to withstand high pressures and temperatures, typically used for containing gases or liquids under extreme conditions.
Allowable Stress for Jacket Material - (Measured in Newton per Square Millimeter) - Allowable Stress for Jacket Material at Design Temperature is defined as the material failure stress divided by a factor of safety greater than one.

STEP 1: Convert Input(s) to Base Unit

Jacket Width: 50 Millimeter --> 50 Millimeter No Conversion Required
Design Jacket Pressure: 0.105 Newton per Square Millimeter --> 0.105 Newton per Square Millimeter No Conversion Required
Allowable Stress for Jacket Material: 120 Newton per Square Millimeter --> 120 Newton per Square Millimeter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

t_rc = 0.886*w_j*sqrt(p_j/f_j) --> 0.886*50*sqrt(0.105/120)

Evaluating ... ...

t_rc = 1.31041167195656

STEP 3: Convert Result to Output's Unit

0.00131041167195656 Meter -->1.31041167195656 Millimeter (Check conversion here)

FINAL ANSWER

1.31041167195656 ≈ 1.310412 Millimeter <-- Required Thickness for Jacket Closer Member

(Calculation completed in 00.011 seconds)

You are here -

Home » Engineering » Chemical Engineering » Process Equipment Design » Jacketed Reaction Vessel » Required Thickness for Jacket Closer Member with Jacket Width

Credits

Created by Heet

Thadomal Shahani Engineering College (Tsec), Mumbai

Heet has created this Calculator and 200+ more calculators!

Verified by Prerana Bakli

University of Hawaiʻi at Mānoa (UH Manoa), Hawaii, USA

Prerana Bakli has verified this Calculator and 1600+ more calculators!

< Jacketed Reaction Vessel Calculators

Maximum Hoop Stress in Coil at Junction with Shell

LaTeX Go Maximum Hoop Stress in Coil at Junction with Shell = (Design Jacket Pressure*Internal Diameter of Half Coil)/(2*Thickness of Half Coil Jacket*Weld Joint Efficiency Factor for Coil)

Required Plate Thickness for Dimple Jacket

LaTeX Go Required Thickness of Dimple Jacket = Maximum Pitch between Steam Weld Centre Lines*sqrt(Design Jacket Pressure/(3*Allowable Stress for Jacket Material))

Required Thickness for Jacket Closer Member with Jacket Width

LaTeX Go Required Thickness for Jacket Closer Member = 0.886*Jacket Width*sqrt(Design Jacket Pressure/Allowable Stress for Jacket Material)

Jacket Width

LaTeX Go Jacket Width = (Inside Diameter of Jacket-Outer Diameter of Vessel)/2

Required Thickness for Jacket Closer Member with Jacket Width Formula

LaTeX Go

Required Thickness for Jacket Closer Member = 0.886*Jacket Width*sqrt(Design Jacket Pressure/Allowable Stress for Jacket Material)
t_rc = 0.886*w_j*sqrt(p_j/f_j)

What is Design Thickness?

Thickness is the one used for the stiffness analysis while the Design Thickness is the one used for reinforcement design. Generally you would use the same value for both. However if there is a situation where you would want the analysis to be based on a certain thickness but the reinforcement calculated based on a different thickness, you could use different values for these. For example you may have some areas in the mat which may be thicker and you may want to consider that additional thickness for the stiffness analysis but when designing the reinforcement, you may choose to use a uniform value for the entire mat.

How to Calculate Required Thickness for Jacket Closer Member with Jacket Width?

Required Thickness for Jacket Closer Member with Jacket Width calculator uses Required Thickness for Jacket Closer Member = 0.886*Jacket Width*sqrt(Design Jacket Pressure/Allowable Stress for Jacket Material) to calculate the Required Thickness for Jacket Closer Member, The Required Thickness for Jacket Closer Member with Jacket Width formula is defined minimum thickness without corrosion allowance for each element of a pressure vessel based on the appropriate design code calculations and code allowable stress that consider pressure, mechanical, and structural loadings. Required Thickness for Jacket Closer Member is denoted by t_rc symbol.

How to calculate Required Thickness for Jacket Closer Member with Jacket Width using this online calculator? To use this online calculator for Required Thickness for Jacket Closer Member with Jacket Width, enter Jacket Width (w_j), Design Jacket Pressure (p_j) & Allowable Stress for Jacket Material (f_j) and hit the calculate button. Here is how the Required Thickness for Jacket Closer Member with Jacket Width calculation can be explained with given input values -> 1310.412 = 0.886*0.05*sqrt(105000/120000000).

FAQ

What is Required Thickness for Jacket Closer Member with Jacket Width?

The Required Thickness for Jacket Closer Member with Jacket Width formula is defined minimum thickness without corrosion allowance for each element of a pressure vessel based on the appropriate design code calculations and code allowable stress that consider pressure, mechanical, and structural loadings and is represented as t_rc = 0.886*w_j*sqrt(p_j/f_j) or Required Thickness for Jacket Closer Member = 0.886*Jacket Width*sqrt(Design Jacket Pressure/Allowable Stress for Jacket Material). Jacket Width is the measurement or extent of something from side to side, Design Jacket Pressure refers to a type of pressure vessel designed to withstand high pressures and temperatures, typically used for containing gases or liquids under extreme conditions & Allowable Stress for Jacket Material at Design Temperature is defined as the material failure stress divided by a factor of safety greater than one.

How to calculate Required Thickness for Jacket Closer Member with Jacket Width?

The Required Thickness for Jacket Closer Member with Jacket Width formula is defined minimum thickness without corrosion allowance for each element of a pressure vessel based on the appropriate design code calculations and code allowable stress that consider pressure, mechanical, and structural loadings is calculated using Required Thickness for Jacket Closer Member = 0.886*Jacket Width*sqrt(Design Jacket Pressure/Allowable Stress for Jacket Material). To calculate Required Thickness for Jacket Closer Member with Jacket Width, you need Jacket Width (w_j), Design Jacket Pressure (p_j) & Allowable Stress for Jacket Material (f_j). With our tool, you need to enter the respective value for Jacket Width, Design Jacket Pressure & Allowable Stress for Jacket Material and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search