LCM of three numbers

Reflected Current using Impedance-1 (Line PL) Calculator

Engineering Chemistry Financial Health More >>

↳

Electrical Chemical Engineering Civil Electronics More >>

⤿

Power System Circuit Graph Theory Control System Electrical Circuit More >>

⤿

Transmission Lines Battery Life FACTS Devices Fault More >>

⤿

Transient Line Performance Characteristics Long Transmission Line Medium Line More >>

⤿

Travelling Waves

⤿

Different Cases for Reflection and Transmission Incident Wave Reflected Waves Relation Between Coefficients More >>

⤿

Line With Parallel Loads Line Is Open Circuited Line Is Short Circuited Load IS Open Circuited More >>

⤿

Impedance 1,2 and 3 Transmitted Coefficient OF Current Transmitted Current 1,2 and 3

✖Reflected Voltage is the voltage that is reflected in the transmission line during transient condition.ⓘ Reflected Voltage [E_r]			+10% -10%
✖The Impedance of Primary Winding is the total of primary Resistance and Reactance.ⓘ Impedance of Primary Winding [Z₁]			+10% -10%

✖Reflected Current is defined as the current wave that is traveling from the receiving end to the sending end of the Transmission line during transient condition.ⓘ Reflected Current using Impedance-1 (Line PL) [I_r]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Transmission Lines Formula PDF PDF Image

Reflected Current using Impedance-1 (Line PL) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Reflected Current = (-1)*Reflected Voltage/Impedance of Primary Winding
I_r = (-1)*E_r/Z₁
This formula uses 3 Variables

Variables Used

Reflected Current - (Measured in Ampere) - Reflected Current is defined as the current wave that is traveling from the receiving end to the sending end of the Transmission line during transient condition.
Reflected Voltage - (Measured in Volt) - Reflected Voltage is the voltage that is reflected in the transmission line during transient condition.
Impedance of Primary Winding - (Measured in Ohm) - The Impedance of Primary Winding is the total of primary Resistance and Reactance.

STEP 1: Convert Input(s) to Base Unit

Reflected Voltage: 4.5 Volt --> 4.5 Volt No Conversion Required
Impedance of Primary Winding: 18 Ohm --> 18 Ohm No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

I_r = (-1)*E_r/Z₁ --> (-1)*4.5/18

Evaluating ... ...

I_r = -0.25

STEP 3: Convert Result to Output's Unit

-0.25 Ampere --> No Conversion Required

FINAL ANSWER

-0.25 Ampere <-- Reflected Current

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Electrical » Power System » Transmission Lines » Transient » Travelling Waves » Different Cases for Reflection and Transmission » Line With Parallel Loads » Reflected Current using Impedance-1 (Line PL)

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Kethavath Srinath

Osmania University (OU), Hyderabad

Kethavath Srinath has verified this Calculator and 1200+ more calculators!

< Line With Parallel Loads Calculators

Reflected Current using Transmitted Current-3 and 2 (Line PL)

LaTeX Go Reflected Current = Incident Current-Transmitted Current-Transmitted Current

Incident Current using Transmitted Current-3 and 2 (Line PL)

LaTeX Go Incident Current = Reflected Current-Transmitted Current-Transmitted Current

Transmitted Voltage using Transmitted Current-2 (Line PL)

LaTeX Go Transmitted Voltage = Transmitted Current*Impedance of Secondary Winding

Transmitted Voltage using Transmitted Current-3 (Line PL)

LaTeX Go Transmitted Voltage = Transmitted Current*Impedance of Tertiary Winding

Reflected Current using Impedance-1 (Line PL) Formula

LaTeX Go

Reflected Current = (-1)*Reflected Voltage/Impedance of Primary Winding
I_r = (-1)*E_r/Z₁

What is Impedance-1?

Impedance-1 is a measure of the overall opposition of a circuit to current-1, in other words: how much the circuit impedes the flow of charge. It is like resistance, but it also takes into account the effects of capacitance and inductance. Impedance-1 is measured in ohms.

How to Calculate Reflected Current using Impedance-1 (Line PL)?

Reflected Current using Impedance-1 (Line PL) calculator uses Reflected Current = (-1)*Reflected Voltage/Impedance of Primary Winding to calculate the Reflected Current, The Reflected Current using Impedance-1 (line PL) formula is defined as the current wave that is traveling from the receiving end to the sending end of the Transmission line. Reflected Current is denoted by I_r symbol.

How to calculate Reflected Current using Impedance-1 (Line PL) using this online calculator? To use this online calculator for Reflected Current using Impedance-1 (Line PL), enter Reflected Voltage (E_r) & Impedance of Primary Winding (Z₁) and hit the calculate button. Here is how the Reflected Current using Impedance-1 (Line PL) calculation can be explained with given input values -> -0.25 = (-1)*4.5/18.

FAQ

What is Reflected Current using Impedance-1 (Line PL)?

The Reflected Current using Impedance-1 (line PL) formula is defined as the current wave that is traveling from the receiving end to the sending end of the Transmission line and is represented as I_r = (-1)*E_r/Z₁ or Reflected Current = (-1)*Reflected Voltage/Impedance of Primary Winding. Reflected Voltage is the voltage that is reflected in the transmission line during transient condition & The Impedance of Primary Winding is the total of primary Resistance and Reactance.

How to calculate Reflected Current using Impedance-1 (Line PL)?

The Reflected Current using Impedance-1 (line PL) formula is defined as the current wave that is traveling from the receiving end to the sending end of the Transmission line is calculated using Reflected Current = (-1)*Reflected Voltage/Impedance of Primary Winding. To calculate Reflected Current using Impedance-1 (Line PL), you need Reflected Voltage (E_r) & Impedance of Primary Winding (Z₁). With our tool, you need to enter the respective value for Reflected Voltage & Impedance of Primary Winding and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Reflected Current?

In this formula, Reflected Current uses Reflected Voltage & Impedance of Primary Winding. We can use 1 other way(s) to calculate the same, which is/are as follows -

Reflected Current = Incident Current-Transmitted Current-Transmitted Current

Home

FREE PDFs

🔍 Search