Receiving End Voltage in End Condenser Method Calculator

✖Sending End Voltage in ECM is the voltage at the sending end of a transmission line.ⓘ Sending End Voltage in ECM [V_s(ecm)]			+10% -10%
✖Sending End Current in ECM is defined as the amount of current injected into a medium transmission line from the source or injectors.ⓘ Sending End Current in ECM [I_s(ecm)]			+10% -10%
✖Impedance in ECM is defined as the amount of opposition faced by the direct or alternating current when it passes through a conductor component, circuit.ⓘ Impedance in ECM [Z_ecm]			+10% -10%

✖Receiving End Voltage in ECM is the voltage developed at the receiving end of a transmission line.ⓘ Receiving End Voltage in End Condenser Method [V_r(ecm)]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download End Condenser Method in Medium Line Formulas PDF PDF Image

Receiving End Voltage in End Condenser Method Solution

STEP 0: Pre-Calculation Summary

Formula Used

Receiving End Voltage in ECM = Sending End Voltage in ECM-(Sending End Current in ECM*Impedance in ECM)
V_r(ecm) = V_s(ecm)-(I_s(ecm)*Z_ecm)
This formula uses 4 Variables

Variables Used

Receiving End Voltage in ECM - (Measured in Volt) - Receiving End Voltage in ECM is the voltage developed at the receiving end of a transmission line.
Sending End Voltage in ECM - (Measured in Volt) - Sending End Voltage in ECM is the voltage at the sending end of a transmission line.
Sending End Current in ECM - (Measured in Ampere) - Sending End Current in ECM is defined as the amount of current injected into a medium transmission line from the source or injectors.
Impedance in ECM - (Measured in Ohm) - Impedance in ECM is defined as the amount of opposition faced by the direct or alternating current when it passes through a conductor component, circuit.

STEP 1: Convert Input(s) to Base Unit

Sending End Voltage in ECM: 400 Volt --> 400 Volt No Conversion Required
Sending End Current in ECM: 16 Ampere --> 16 Ampere No Conversion Required
Impedance in ECM: 9 Ohm --> 9 Ohm No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

V_r(ecm) = V_s(ecm)-(I_s(ecm)*Z_ecm) --> 400-(16*9)

Evaluating ... ...

V_r(ecm) = 256

STEP 3: Convert Result to Output's Unit

256 Volt --> No Conversion Required

FINAL ANSWER

256 Volt <-- Receiving End Voltage in ECM

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Power System » Transmission Lines » Medium Line » End Condenser Method in Medium Line » Receiving End Voltage in End Condenser Method

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< End Condenser Method in Medium Line Calculators

Sending End Voltage in End Condenser Method

LaTeX Go Sending End Voltage in ECM = Receiving End Voltage in ECM+(Sending End Current in ECM*Impedance in ECM)

Receiving End Current in End Condenser Method

LaTeX Go Receiving End Current in ECM = Sending End Current in ECM-Capacitive Current in ECM

Sending End Current in End Condenser Method

LaTeX Go Sending End Current in ECM = Receiving End Current in ECM+Capacitive Current in ECM

Capacitive Current in End Condenser Method

LaTeX Go Capacitive Current in ECM = Sending End Current in ECM-Receiving End Current in ECM

Receiving End Voltage in End Condenser Method Formula

LaTeX Go

Receiving End Voltage in ECM = Sending End Voltage in ECM-(Sending End Current in ECM*Impedance in ECM)
V_r(ecm) = V_s(ecm)-(I_s(ecm)*Z_ecm)

What are the disadvantages of condenser end?

Although the end condenser method for the solution of medium lines is simple to work out calculations, yet it has the following drawbacks. There is a considerable error (about 10%) in calculations because the distributed capacitance has been assumed to be lumped or concentrated.

What is end condenser method?

In this method, the capacitance of the line is lumped or concentrated at the receiving or load end. This method of localizing the line capacitance at the load end overestimates the effects of capacitance.

How to Calculate Receiving End Voltage in End Condenser Method?

Receiving End Voltage in End Condenser Method calculator uses Receiving End Voltage in ECM = Sending End Voltage in ECM-(Sending End Current in ECM*Impedance in ECM) to calculate the Receiving End Voltage in ECM, The Receiving End Voltage in End Condenser Method formula is defined as the voltage at the receiving end of the medium transmission lines. Receiving End Voltage in ECM is denoted by V_r(ecm) symbol.

How to calculate Receiving End Voltage in End Condenser Method using this online calculator? To use this online calculator for Receiving End Voltage in End Condenser Method, enter Sending End Voltage in ECM (V_s(ecm)), Sending End Current in ECM (I_s(ecm)) & Impedance in ECM (Z_ecm) and hit the calculate button. Here is how the Receiving End Voltage in End Condenser Method calculation can be explained with given input values -> 256 = 400-(16*9).

FAQ

What is Receiving End Voltage in End Condenser Method?

The Receiving End Voltage in End Condenser Method formula is defined as the voltage at the receiving end of the medium transmission lines and is represented as V_r(ecm) = V_s(ecm)-(I_s(ecm)*Z_ecm) or Receiving End Voltage in ECM = Sending End Voltage in ECM-(Sending End Current in ECM*Impedance in ECM). Sending End Voltage in ECM is the voltage at the sending end of a transmission line, Sending End Current in ECM is defined as the amount of current injected into a medium transmission line from the source or injectors & Impedance in ECM is defined as the amount of opposition faced by the direct or alternating current when it passes through a conductor component, circuit.

How to calculate Receiving End Voltage in End Condenser Method?

The Receiving End Voltage in End Condenser Method formula is defined as the voltage at the receiving end of the medium transmission lines is calculated using Receiving End Voltage in ECM = Sending End Voltage in ECM-(Sending End Current in ECM*Impedance in ECM). To calculate Receiving End Voltage in End Condenser Method, you need Sending End Voltage in ECM (V_s(ecm)), Sending End Current in ECM (I_s(ecm)) & Impedance in ECM (Z_ecm). With our tool, you need to enter the respective value for Sending End Voltage in ECM, Sending End Current in ECM & Impedance in ECM and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search