Receiving End Current using Receiving End Power (STL) Calculator

✖Receiving End Power is defined as the power at receiving end in a short transmission line.ⓘ Receiving End Power [P_r]			+10% -10%
✖Receiving End Voltage is the voltage developed at the receiving end of a short transmission line.ⓘ Receiving End Voltage [V_r]			+10% -10%
✖Receiving End Phase Angle is the difference between the phasor of the current and voltage at the receiving end of a short transmission line.ⓘ Receiving End Phase Angle [Φ_r]			+10% -10%

✖Receiving End Current is defined as the magnitude and phase angle of current received at the load end of a short transmission line.ⓘ Receiving End Current using Receiving End Power (STL) [I_r]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Short Line Formulas PDF PDF Image

Receiving End Current using Receiving End Power (STL) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Receiving End Current = Receiving End Power/(3*Receiving End Voltage*cos(Receiving End Phase Angle))
I_r = P_r/(3*V_r*cos(Φ_r))
This formula uses 1 Functions, 4 Variables

Functions Used

cos - Cosine of an angle is the ratio of the side adjacent to the angle to the hypotenuse of the triangle., cos(Angle)

Variables Used

Receiving End Current - (Measured in Ampere) - Receiving End Current is defined as the magnitude and phase angle of current received at the load end of a short transmission line.
Receiving End Power - (Measured in Watt) - Receiving End Power is defined as the power at receiving end in a short transmission line.
Receiving End Voltage - (Measured in Volt) - Receiving End Voltage is the voltage developed at the receiving end of a short transmission line.
Receiving End Phase Angle - (Measured in Radian) - Receiving End Phase Angle is the difference between the phasor of the current and voltage at the receiving end of a short transmission line.

STEP 1: Convert Input(s) to Base Unit

Receiving End Power: 1150 Watt --> 1150 Watt No Conversion Required
Receiving End Voltage: 380 Volt --> 380 Volt No Conversion Required
Receiving End Phase Angle: 75 Degree --> 1.3089969389955 Radian (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

I_r = P_r/(3*V_r*cos(Φ_r)) --> 1150/(3*380*cos(1.3089969389955))

Evaluating ... ...

I_r = 3.89759543940844

STEP 3: Convert Result to Output's Unit

3.89759543940844 Ampere --> No Conversion Required

FINAL ANSWER

3.89759543940844 ≈ 3.897595 Ampere <-- Receiving End Current

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Power System » Transmission Lines » Short Line » Current » Receiving End Current using Receiving End Power (STL)

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< Current Calculators

Receiving End Current using Transmission Efficiency (STL)

LaTeX Go Receiving End Current = Transmission Efficiency*Sending End Voltage*Sending End Current*cos(Sending End Phase Angle)/(Receiving End Voltage*cos(Receiving End Phase Angle))

Receiving End Current using Receiving End Power (STL)

LaTeX Go Receiving End Current = Receiving End Power/(3*Receiving End Voltage*cos(Receiving End Phase Angle))

Sending End Current using Sending End Power (STL)

LaTeX Go Sending End Current = Sending End Power/(3*Sending End Voltage*cos(Sending End Phase Angle))

Receiving End Current using Losses (STL)

LaTeX Go Receiving End Current = sqrt(Power Loss/(3*Resistance))

Receiving End Current using Receiving End Power (STL) Formula

LaTeX Go

Receiving End Current = Receiving End Power/(3*Receiving End Voltage*cos(Receiving End Phase Angle))
I_r = P_r/(3*V_r*cos(Φ_r))

What is short transmission line?

A short transmission line is defined as a transmission line with an effective length less than ₈₀ km (₅₀ miles), or with a voltage less than ₆₉ kV. Unlike medium transmission lines and long transmission lines, the line charging current is negligible, and hence the shunt capacitance can be ignored.

How to Calculate Receiving End Current using Receiving End Power (STL)?

Receiving End Current using Receiving End Power (STL) calculator uses Receiving End Current = Receiving End Power/(3*Receiving End Voltage*cos(Receiving End Phase Angle)) to calculate the Receiving End Current, The Receiving End Current using Receiving End Power (STL) is the current that flows into the load connected at the end of the line, considering line impedance negligible. It is determined by the receiving end voltage and load impedance, typically calculated using Ohm's law. Receiving End Current is denoted by I_r symbol.

How to calculate Receiving End Current using Receiving End Power (STL) using this online calculator? To use this online calculator for Receiving End Current using Receiving End Power (STL), enter Receiving End Power (P_r), Receiving End Voltage (V_r) & Receiving End Phase Angle (Φ_r) and hit the calculate button. Here is how the Receiving End Current using Receiving End Power (STL) calculation can be explained with given input values -> 3.897595 = 1150/(3*380*cos(1.3089969389955)).

FAQ

What is Receiving End Current using Receiving End Power (STL)?

The Receiving End Current using Receiving End Power (STL) is the current that flows into the load connected at the end of the line, considering line impedance negligible. It is determined by the receiving end voltage and load impedance, typically calculated using Ohm's law and is represented as I_r = P_r/(3*V_r*cos(Φ_r)) or Receiving End Current = Receiving End Power/(3*Receiving End Voltage*cos(Receiving End Phase Angle)). Receiving End Power is defined as the power at receiving end in a short transmission line, Receiving End Voltage is the voltage developed at the receiving end of a short transmission line & Receiving End Phase Angle is the difference between the phasor of the current and voltage at the receiving end of a short transmission line.

How to calculate Receiving End Current using Receiving End Power (STL)?

The Receiving End Current using Receiving End Power (STL) is the current that flows into the load connected at the end of the line, considering line impedance negligible. It is determined by the receiving end voltage and load impedance, typically calculated using Ohm's law is calculated using Receiving End Current = Receiving End Power/(3*Receiving End Voltage*cos(Receiving End Phase Angle)). To calculate Receiving End Current using Receiving End Power (STL), you need Receiving End Power (P_r), Receiving End Voltage (V_r) & Receiving End Phase Angle (Φ_r). With our tool, you need to enter the respective value for Receiving End Power, Receiving End Voltage & Receiving End Phase Angle and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Receiving End Current?

In this formula, Receiving End Current uses Receiving End Power, Receiving End Voltage & Receiving End Phase Angle. We can use 3 other way(s) to calculate the same, which is/are as follows -

Receiving End Current = Transmission Efficiency*Sending End Voltage*Sending End Current*cos(Sending End Phase Angle)/(Receiving End Voltage*cos(Receiving End Phase Angle))
Receiving End Current = sqrt(Power Loss/(3*Resistance))
Receiving End Current = ((3*Sending End Voltage*Sending End Current*cos(Sending End Phase Angle))-Power Loss)/(3*Receiving End Voltage*cos(Receiving End Phase Angle))

Home

FREE PDFs

🔍 Search