Power Drain from Positive Sine Wave Calculator

✖Peak Voltage is the peak or maximum voltage of a circuit/ rectifier.ⓘ Peak Voltage [V_m]			+10% -10%
✖Supply Voltage is the input voltage source which flows through the zener diode.ⓘ Supply Voltage [V_i]			+10% -10%
✖Load resistance is the resistance value of load given for the network.ⓘ Load Resistance [R_L]			+10% -10%

✖Power Drained is the amount of energy liberated per second in a low frequency amplifier.ⓘ Power Drain from Positive Sine Wave [P]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Low Frequency Response Amplifiers Formulas PDF PDF Image

Power Drain from Positive Sine Wave Solution

STEP 0: Pre-Calculation Summary

Formula Used

Power Drained = (Peak Voltage*Supply Voltage)/(pi*Load Resistance)
P = (V_m*V_i)/(pi*R_L)
This formula uses 1 Constants, 4 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Variables Used

Power Drained - (Measured in Watt) - Power Drained is the amount of energy liberated per second in a low frequency amplifier.
Peak Voltage - (Measured in Volt) - Peak Voltage is the peak or maximum voltage of a circuit/ rectifier.
Supply Voltage - (Measured in Volt) - Supply Voltage is the input voltage source which flows through the zener diode.
Load Resistance - (Measured in Ohm) - Load resistance is the resistance value of load given for the network.

STEP 1: Convert Input(s) to Base Unit

Peak Voltage: 6 Volt --> 6 Volt No Conversion Required
Supply Voltage: 12 Volt --> 12 Volt No Conversion Required
Load Resistance: 4.5 Kilohm --> 4500 Ohm (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

P = (V_m*V_i)/(pi*R_L) --> (6*12)/(pi*4500)

Evaluating ... ...

P = 0.00509295817894065

STEP 3: Convert Result to Output's Unit

0.00509295817894065 Watt -->5.09295817894065 Milliwatt (Check conversion here)

FINAL ANSWER

5.09295817894065 ≈ 5.092958 Milliwatt <-- Power Drained

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Electronics » Amplifiers » Low Frequency Response Amplifiers » Response Analysis » Power Drain from Positive Sine Wave

Credits

Created by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has created this Calculator and 600+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Response Analysis Calculators

Power Drain from Positive Sine Wave

LaTeX Go Power Drained = (Peak Voltage*Supply Voltage)/(pi*Load Resistance)

Peak Voltage of Positive Sine Wave

LaTeX Go Peak Voltage = (pi*Power Drained*Load Resistance)/Supply Voltage

Unity-Gain Bandwidth

LaTeX Go Unity Gain Bandwidth = Common Emitter Current Gain*3-dB Frequency

Transition Frequency

LaTeX Go Transition Frequency = 1/sqrt(Constant B)

Power Drain from Positive Sine Wave Formula

LaTeX Go

Power Drained = (Peak Voltage*Supply Voltage)/(pi*Load Resistance)
P = (V_m*V_i)/(pi*R_L)

What is a Class B amplifier?

Class B amplifier is a type of power amplifier where the active device (transistor) conducts only for the one-half cycle of the input signal. Since the active device is switched off for half the input cycle, the active device dissipates less power and hence the efficiency is improved.

How to Calculate Power Drain from Positive Sine Wave?

Power Drain from Positive Sine Wave calculator uses Power Drained = (Peak Voltage*Supply Voltage)/(pi*Load Resistance) to calculate the Power Drained, Power Drain from Positive Sine Wave is defined as the rate at which energy is being consumed or drawn from a Positive Sine Wave. Power Drained is denoted by P symbol.

How to calculate Power Drain from Positive Sine Wave using this online calculator? To use this online calculator for Power Drain from Positive Sine Wave, enter Peak Voltage (V_m), Supply Voltage (V_i) & Load Resistance (R_L) and hit the calculate button. Here is how the Power Drain from Positive Sine Wave calculation can be explained with given input values -> 5092.958 = (6*12)/(pi*4500).

FAQ

What is Power Drain from Positive Sine Wave?

Power Drain from Positive Sine Wave is defined as the rate at which energy is being consumed or drawn from a Positive Sine Wave and is represented as P = (V_m*V_i)/(pi*R_L) or Power Drained = (Peak Voltage*Supply Voltage)/(pi*Load Resistance). Peak Voltage is the peak or maximum voltage of a circuit/ rectifier, Supply Voltage is the input voltage source which flows through the zener diode & Load resistance is the resistance value of load given for the network.

How to calculate Power Drain from Positive Sine Wave?

Power Drain from Positive Sine Wave is defined as the rate at which energy is being consumed or drawn from a Positive Sine Wave is calculated using Power Drained = (Peak Voltage*Supply Voltage)/(pi*Load Resistance). To calculate Power Drain from Positive Sine Wave, you need Peak Voltage (V_m), Supply Voltage (V_i) & Load Resistance (R_L). With our tool, you need to enter the respective value for Peak Voltage, Supply Voltage & Load Resistance and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search