Positive Sequence Voltage of STATCOM Calculator

✖SVC Reference Voltage is defined as the desired or target voltage level that the SVC aims to maintain or regulate at its point of connection to the power system.ⓘ SVC Reference Voltage [ΔV_ref]			+10% -10%
✖Droop Reactance in STATCOM is defined as the slope or sensitivity of the droop control of the reactive power output.ⓘ Droop Reactance in STATCOM [X_droop]			+10% -10%
✖Maximum Inductive Reactive Current is defined as the peak value of the current that flows in an inductive component of an AC circuit.ⓘ Maximum Inductive Reactive Current [I_r(max)]			+10% -10%

✖Positive Sequence Voltage in STATCOM is defined as the component of voltage that corresponds to the positive sequence of the three-phase system.ⓘ Positive Sequence Voltage of STATCOM [V_po]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download FACTS Devices Formulas PDF PDF Image

Positive Sequence Voltage of STATCOM Solution

STEP 0: Pre-Calculation Summary

Formula Used

Positive Sequence Voltage in STATCOM = SVC Reference Voltage+Droop Reactance in STATCOM*Maximum Inductive Reactive Current
V_po = ΔV_ref+X_droop*I_r(max)
This formula uses 4 Variables

Variables Used

Positive Sequence Voltage in STATCOM - (Measured in Volt) - Positive Sequence Voltage in STATCOM is defined as the component of voltage that corresponds to the positive sequence of the three-phase system.
SVC Reference Voltage - (Measured in Volt) - SVC Reference Voltage is defined as the desired or target voltage level that the SVC aims to maintain or regulate at its point of connection to the power system.
Droop Reactance in STATCOM - (Measured in Ohm) - Droop Reactance in STATCOM is defined as the slope or sensitivity of the droop control of the reactive power output.
Maximum Inductive Reactive Current - (Measured in Ampere) - Maximum Inductive Reactive Current is defined as the peak value of the current that flows in an inductive component of an AC circuit.

STEP 1: Convert Input(s) to Base Unit

SVC Reference Voltage: 15.25 Volt --> 15.25 Volt No Conversion Required
Droop Reactance in STATCOM: 10 Ohm --> 10 Ohm No Conversion Required
Maximum Inductive Reactive Current: 7 Ampere --> 7 Ampere No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

V_po = ΔV_ref+X_droop*I_r(max) --> 15.25+10*7

Evaluating ... ...

V_po = 85.25

STEP 3: Convert Result to Output's Unit

85.25 Volt --> No Conversion Required

FINAL ANSWER

85.25 Volt <-- Positive Sequence Voltage in STATCOM

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Power System » FACTS Devices » Static Synchronous Compensator(STATCOM) » Positive Sequence Voltage of STATCOM

Credits

Created by Dipanjona Mallick

Heritage Insitute of technology (HITK), Kolkata

Dipanjona Mallick has created this Calculator and 25+ more calculators!

Verified by Aman Dhussawat

GURU TEGH BAHADUR INSTITUTE OF TECHNOLOGY (GTBIT), NEW DELHI

Aman Dhussawat has verified this Calculator and 100+ more calculators!

< Static Synchronous Compensator(STATCOM) Calculators

RMS Error Vector in Load Distribution under STATCOM

LaTeX Go RMS Error Vector = sqrt((1/Time Elapsed in PWM Current Controller)*int((Error Vector in Line 1)^2+(Error Vector in Line 2)^2+(Error Vector in Line 3)^2*x,x,0,Time Elapsed in PWM Current Controller))

Positive Sequence Voltage of STATCOM

LaTeX Go Positive Sequence Voltage in STATCOM = SVC Reference Voltage+Droop Reactance in STATCOM*Maximum Inductive Reactive Current

Positive Sequence Voltage of STATCOM Formula

LaTeX Go

Positive Sequence Voltage in STATCOM = SVC Reference Voltage+Droop Reactance in STATCOM*Maximum Inductive Reactive Current
V_po = ΔV_ref+X_droop*I_r(max)

What is the Positive Sequence Voltage of STATCOM?

Positive Sequence Voltage of STATCOM is used in V-I Characteristics of STATCOM or commonly known as Static Synchronous Compensator. The term positive sequence voltage is referred to as the component of voltage that corresponds to the positive sequence of the three-phase system, similarly for a sinusoidal three-phase system, the positive sequence voltage is a set of three sinusoidal voltages that rotate in the same direction with the same frequency.

How to Calculate Positive Sequence Voltage of STATCOM?

Positive Sequence Voltage of STATCOM calculator uses Positive Sequence Voltage in STATCOM = SVC Reference Voltage+Droop Reactance in STATCOM*Maximum Inductive Reactive Current to calculate the Positive Sequence Voltage in STATCOM, The Positive Sequence Voltage of STATCOM formula is defined as the component of voltage that corresponds to the positive sequence of the three-phase system. Positive Sequence Voltage in STATCOM is denoted by V_po symbol.

How to calculate Positive Sequence Voltage of STATCOM using this online calculator? To use this online calculator for Positive Sequence Voltage of STATCOM, enter SVC Reference Voltage (ΔV_ref), Droop Reactance in STATCOM (X_droop) & Maximum Inductive Reactive Current (I_r(max)) and hit the calculate button. Here is how the Positive Sequence Voltage of STATCOM calculation can be explained with given input values -> 85.25 = 15.25+10*7.

FAQ

What is Positive Sequence Voltage of STATCOM?

The Positive Sequence Voltage of STATCOM formula is defined as the component of voltage that corresponds to the positive sequence of the three-phase system and is represented as V_po = ΔV_ref+X_droop*I_r(max) or Positive Sequence Voltage in STATCOM = SVC Reference Voltage+Droop Reactance in STATCOM*Maximum Inductive Reactive Current. SVC Reference Voltage is defined as the desired or target voltage level that the SVC aims to maintain or regulate at its point of connection to the power system, Droop Reactance in STATCOM is defined as the slope or sensitivity of the droop control of the reactive power output & Maximum Inductive Reactive Current is defined as the peak value of the current that flows in an inductive component of an AC circuit.

How to calculate Positive Sequence Voltage of STATCOM?

The Positive Sequence Voltage of STATCOM formula is defined as the component of voltage that corresponds to the positive sequence of the three-phase system is calculated using Positive Sequence Voltage in STATCOM = SVC Reference Voltage+Droop Reactance in STATCOM*Maximum Inductive Reactive Current. To calculate Positive Sequence Voltage of STATCOM, you need SVC Reference Voltage (ΔV_ref), Droop Reactance in STATCOM (X_droop) & Maximum Inductive Reactive Current (I_r(max)). With our tool, you need to enter the respective value for SVC Reference Voltage, Droop Reactance in STATCOM & Maximum Inductive Reactive Current and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search