LCM of two numbers

Positive Moment for End Spans if Discontinuous End is Integral with Support Calculator

Engineering Chemistry Financial Health More >>

↳

Civil Chemical Engineering Electrical Electronics More >>

⤿

Structural Engineering Bridge and Suspension Cable Coastal and Ocean Engineering Columns More >>

⤿

Concrete Structures Prestressed Concrete Roof Live Loads Structural Analysis

⤿

Behaviour in Flexure Properties of Basic Material of Concrete Structures Design for Beams and Ultimate Strength for Rectangular Beams with Tension Reinforcement Design of Compression Members More >>

⤿

Design of Beam and Slab Analysis using Limit State Method Analysis Using Working Stress Method

⤿

Design of Continuous One Way Slabs Curtailment of Flexural Tension Reinforcement Doubly Reinforced Rectangular Sections Singly Reinforced Rectangular Sections

⤿

Use of Moment Coefficients

✖Vertical Load are applied perpendicular to the surface.ⓘ Vertical Load [W_load]			+10% -10%
✖Length of Span refers to the length of the opening above which the beam is spanning.ⓘ Length of Span [I_n]			+10% -10%

✖The Moment in Structures is an overturning effect (tends to bend or turn the member) created by the force(load) acting on a structural member.ⓘ Positive Moment for End Spans if Discontinuous End is Integral with Support [M_t]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Design of Beam and Slab Formulas PDF PDF Image

Positive Moment for End Spans if Discontinuous End is Integral with Support Solution

STEP 0: Pre-Calculation Summary

Formula Used

Moment in Structures = (Vertical Load*Length of Span^2)/14
M_t = (W_load*I_n^2)/14
This formula uses 3 Variables

Variables Used

Moment in Structures - (Measured in Joule) - The Moment in Structures is an overturning effect (tends to bend or turn the member) created by the force(load) acting on a structural member.
Vertical Load - (Measured in Kilonewton) - Vertical Load are applied perpendicular to the surface.
Length of Span - (Measured in Meter) - Length of Span refers to the length of the opening above which the beam is spanning.

STEP 1: Convert Input(s) to Base Unit

Vertical Load: 3.6 Kilonewton --> 3.6 Kilonewton No Conversion Required
Length of Span: 10.01 Meter --> 10.01 Meter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

M_t = (W_load*I_n^2)/14 --> (3.6*10.01^2)/14

Evaluating ... ...

M_t = 25.76574

STEP 3: Convert Result to Output's Unit

25.76574 Joule -->25.76574 Newton Meter (Check conversion here)

FINAL ANSWER

25.76574 Newton Meter <-- Moment in Structures

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Civil » Structural Engineering » Concrete Structures » Behaviour in Flexure » Design of Beam and Slab » Design of Continuous One Way Slabs » Use of Moment Coefficients » Positive Moment for End Spans if Discontinuous End is Integral with Support

Credits

Created by Kethavath Srinath

Osmania University (OU), Hyderabad

Kethavath Srinath has created this Calculator and 1000+ more calculators!

Verified by Mridul Sharma

Indian Institute of Information Technology (IIIT), Bhopal

Mridul Sharma has verified this Calculator and 1700+ more calculators!

< Use of Moment Coefficients Calculators

Positive Moment for End Spans if Discontinuous End is Integral with Support

LaTeX Go Moment in Structures = (Vertical Load*Length of Span^2)/14

Positive Moment for End Spans if Discontinuous End is Unrestrained

LaTeX Go Moment in Structures = (Vertical Load*Length of Span^2)/11

Positive Moment for Interior Spans

LaTeX Go Moment in Structures = (Vertical Load*Length of Span^2)/16

Negative Moment at Exterior Face of First Interior Support for Two Spans

LaTeX Go Moment in Structures = (Vertical Load*Length of Span^2)/9

Positive Moment for End Spans if Discontinuous End is Integral with Support Formula

LaTeX Go

Moment in Structures = (Vertical Load*Length of Span^2)/14
M_t = (W_load*I_n^2)/14

Define Moment

The Moment of a force is a measure of its tendency to cause a body to rotate about a specific point or axis. This is different from the tendency for a body to move, or translate, in the direction of the force.

How to Calculate Positive Moment for End Spans if Discontinuous End is Integral with Support?

Positive Moment for End Spans if Discontinuous End is Integral with Support calculator uses Moment in Structures = (Vertical Load*Length of Span^2)/14 to calculate the Moment in Structures, The Positive Moment for End Spans if Discontinuous End is Integral with Support is defined as the beam/slab is being forced to curve downwards or Sag (forming a smile) in the mid span. Moment in Structures is denoted by M_t symbol.

How to calculate Positive Moment for End Spans if Discontinuous End is Integral with Support using this online calculator? To use this online calculator for Positive Moment for End Spans if Discontinuous End is Integral with Support, enter Vertical Load (W_load) & Length of Span (I_n) and hit the calculate button. Here is how the Positive Moment for End Spans if Discontinuous End is Integral with Support calculation can be explained with given input values -> 0.025714 = (3600*0.01001^2)/14.

FAQ

What is Positive Moment for End Spans if Discontinuous End is Integral with Support?

The Positive Moment for End Spans if Discontinuous End is Integral with Support is defined as the beam/slab is being forced to curve downwards or Sag (forming a smile) in the mid span and is represented as M_t = (W_load*I_n^2)/14 or Moment in Structures = (Vertical Load*Length of Span^2)/14. Vertical Load are applied perpendicular to the surface & Length of Span refers to the length of the opening above which the beam is spanning.

How to calculate Positive Moment for End Spans if Discontinuous End is Integral with Support?

The Positive Moment for End Spans if Discontinuous End is Integral with Support is defined as the beam/slab is being forced to curve downwards or Sag (forming a smile) in the mid span is calculated using Moment in Structures = (Vertical Load*Length of Span^2)/14. To calculate Positive Moment for End Spans if Discontinuous End is Integral with Support, you need Vertical Load (W_load) & Length of Span (I_n). With our tool, you need to enter the respective value for Vertical Load & Length of Span and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Moment in Structures?

In this formula, Moment in Structures uses Vertical Load & Length of Span. We can use 3 other way(s) to calculate the same, which is/are as follows -

Moment in Structures = (Vertical Load*Length of Span^2)/11
Moment in Structures = (Vertical Load*Length of Span^2)/16
Moment in Structures = (Vertical Load*Length of Span^2)/9

Home

FREE PDFs

🔍 Search