Pitch of rivet given tearing strength of rivet Calculator

✖Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.ⓘ Rivet Diameter [D_rivet]			+10% -10%
✖Tearing strength is defined as the force required to start or to continue to tear a fabric, in either weft or warp direction, under specified conditions.ⓘ Tearing Strength [T_strength]			+10% -10%
✖Tensile stress can be defined as the magnitude of force applied along an elastic rod, which is divided by the cross-sectional area of the rod in a direction perpendicular to the applied force.ⓘ Tensile Stress [σ_t]			+10% -10%
✖The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.ⓘ Thickness of Plate [t_plate]			+10% -10%

✖Pitch of Rivet is defined as the distance between the centers of adjacent rivets that hold together the parts of a built member.ⓘ Pitch of rivet given tearing strength of rivet [p]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Strength of Materials Formula PDF PDF Image

Pitch of rivet given tearing strength of rivet Solution

STEP 0: Pre-Calculation Summary

Formula Used

Pitch of Rivet = Rivet Diameter+(Tearing Strength/(Tensile Stress*Thickness of Plate))
p = D_rivet+(T_strength/(σ_t*t_plate))
This formula uses 5 Variables

Variables Used

Pitch of Rivet - (Measured in Meter) - Pitch of Rivet is defined as the distance between the centers of adjacent rivets that hold together the parts of a built member.
Rivet Diameter - (Measured in Meter) - Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.
Tearing Strength - (Measured in Newton) - Tearing strength is defined as the force required to start or to continue to tear a fabric, in either weft or warp direction, under specified conditions.
Tensile Stress - (Measured in Pascal) - Tensile stress can be defined as the magnitude of force applied along an elastic rod, which is divided by the cross-sectional area of the rod in a direction perpendicular to the applied force.
Thickness of Plate - (Measured in Meter) - The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

STEP 1: Convert Input(s) to Base Unit

Rivet Diameter: 18 Millimeter --> 0.018 Meter (Check conversion here)
Tearing Strength: 4 Kilonewton --> 4000 Newton (Check conversion here)
Tensile Stress: 0.173 Megapascal --> 173000 Pascal (Check conversion here)
Thickness of Plate: 12 Millimeter --> 0.012 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

p = D_rivet+(T_strength/(σ_t*t_plate)) --> 0.018+(4000/(173000*0.012))

Evaluating ... ...

p = 1.94478227360308

STEP 3: Convert Result to Output's Unit

1.94478227360308 Meter -->1944.78227360308 Millimeter (Check conversion here)

FINAL ANSWER

1944.78227360308 ≈ 1944.782 Millimeter <-- Pitch of Rivet

(Calculation completed in 00.004 seconds)

You are here -

Home » Physics » Strength of Materials » Riveted Joint » Strength of a Riveted Joint » Mechanical » Stress in Rivet » Pitch of rivet given tearing strength of rivet

Credits

Created by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has created this Calculator and 2000+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< Stress in Rivet Calculators

Number of rivets given shearing strength if rivet is in single shear

LaTeX Go Number of Rivets Per Pitch = Shear Strength/(1*(pi/4)*Shear Stress in Joint*(Rivet Diameter^2))

Shearing strength if rivet is in single shear

LaTeX Go Shear Strength = (1*Number of Rivets Per Pitch*(pi/4)*Shear Stress in Joint*(Rivet Diameter^2))

Pitch of rivet given tearing strength of rivet

LaTeX Go Pitch of Rivet = Rivet Diameter+(Tearing Strength/(Tensile Stress*Thickness of Plate))

Tearing strength of rivet

LaTeX Go Tearing Strength = Tensile Stress*(Pitch of Rivet-Rivet Diameter)*Thickness of Plate

Pitch of rivet given tearing strength of rivet Formula

LaTeX Go

Pitch of Rivet = Rivet Diameter+(Tearing Strength/(Tensile Stress*Thickness of Plate))
p = D_rivet+(T_strength/(σ_t*t_plate))

What is tear and tensile strength?

Tear strength is the measure of how much tensile stress the material can withstand in a specific case, i.e. when a tear has been introduced in the material, whereas a normal tensile stress test is done for a non-defective piece of material.

How to Calculate Pitch of rivet given tearing strength of rivet?

Pitch of rivet given tearing strength of rivet calculator uses Pitch of Rivet = Rivet Diameter+(Tearing Strength/(Tensile Stress*Thickness of Plate)) to calculate the Pitch of Rivet, The Pitch of rivet given tearing strength of rivet formula is defined as the distance between two consecutive rivets measured parallel to the direction of the force in the structural member, lying on the same rivet line. Pitch of Rivet is denoted by p symbol.

How to calculate Pitch of rivet given tearing strength of rivet using this online calculator? To use this online calculator for Pitch of rivet given tearing strength of rivet, enter Rivet Diameter (D_rivet), Tearing Strength (T_strength), Tensile Stress (σ_t) & Thickness of Plate (t_plate) and hit the calculate button. Here is how the Pitch of rivet given tearing strength of rivet calculation can be explained with given input values -> 1.9E+6 = 0.018+(4000/(173000*0.012)).

FAQ

What is Pitch of rivet given tearing strength of rivet?

The Pitch of rivet given tearing strength of rivet formula is defined as the distance between two consecutive rivets measured parallel to the direction of the force in the structural member, lying on the same rivet line and is represented as p = D_rivet+(T_strength/(σ_t*t_plate)) or Pitch of Rivet = Rivet Diameter+(Tearing Strength/(Tensile Stress*Thickness of Plate)). Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long, Tearing strength is defined as the force required to start or to continue to tear a fabric, in either weft or warp direction, under specified conditions, Tensile stress can be defined as the magnitude of force applied along an elastic rod, which is divided by the cross-sectional area of the rod in a direction perpendicular to the applied force & The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

How to calculate Pitch of rivet given tearing strength of rivet?

The Pitch of rivet given tearing strength of rivet formula is defined as the distance between two consecutive rivets measured parallel to the direction of the force in the structural member, lying on the same rivet line is calculated using Pitch of Rivet = Rivet Diameter+(Tearing Strength/(Tensile Stress*Thickness of Plate)). To calculate Pitch of rivet given tearing strength of rivet, you need Rivet Diameter (D_rivet), Tearing Strength (T_strength), Tensile Stress (σ_t) & Thickness of Plate (t_plate). With our tool, you need to enter the respective value for Rivet Diameter, Tearing Strength, Tensile Stress & Thickness of Plate and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Pitch of Rivet?

In this formula, Pitch of Rivet uses Rivet Diameter, Tearing Strength, Tensile Stress & Thickness of Plate. We can use 2 other way(s) to calculate the same, which is/are as follows -

Pitch of Rivet = Least Value of Strength/(Tensile Stress*Thickness of Plate*Efficiency of Riveted Joint)
Pitch of Rivet = Strength of Solid Plate/(Tensile Stress*Thickness of Plate)

Home

FREE PDFs

🔍 Search