Peak Voltage of Positive Sine Wave Calculator

✖Power Drained is the amount of energy liberated per second in a low frequency amplifier.ⓘ Power Drained [P]			+10% -10%
✖Load resistance is the resistance value of load given for the network.ⓘ Load Resistance [R_L]			+10% -10%
✖Supply Voltage is the input voltage source which flows through the zener diode.ⓘ Supply Voltage [V_i]			+10% -10%

✖Peak Voltage is the peak or maximum voltage of a circuit/ rectifier.ⓘ Peak Voltage of Positive Sine Wave [V_m]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Low Frequency Response Amplifiers Formulas PDF PDF Image

Peak Voltage of Positive Sine Wave Solution

STEP 0: Pre-Calculation Summary

Formula Used

Peak Voltage = (pi*Power Drained*Load Resistance)/Supply Voltage
V_m = (pi*P*R_L)/V_i
This formula uses 1 Constants, 4 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Variables Used

Peak Voltage - (Measured in Volt) - Peak Voltage is the peak or maximum voltage of a circuit/ rectifier.
Power Drained - (Measured in Watt) - Power Drained is the amount of energy liberated per second in a low frequency amplifier.
Load Resistance - (Measured in Ohm) - Load resistance is the resistance value of load given for the network.
Supply Voltage - (Measured in Volt) - Supply Voltage is the input voltage source which flows through the zener diode.

STEP 1: Convert Input(s) to Base Unit

Power Drained: 5.08 Milliwatt --> 0.00508 Watt (Check conversion here)
Load Resistance: 4.5 Kilohm --> 4500 Ohm (Check conversion here)
Supply Voltage: 12 Volt --> 12 Volt No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

V_m = (pi*P*R_L)/V_i --> (pi*0.00508*4500)/12

Evaluating ... ...

V_m = 5.98473400508856

STEP 3: Convert Result to Output's Unit

5.98473400508856 Volt --> No Conversion Required

FINAL ANSWER

5.98473400508856 ≈ 5.984734 Volt <-- Peak Voltage

(Calculation completed in 00.007 seconds)

You are here -

Home » Engineering » Electronics » Amplifiers » Low Frequency Response Amplifiers » Response Analysis » Peak Voltage of Positive Sine Wave

Credits

Created by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has created this Calculator and 600+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Response Analysis Calculators

Power Drain from Positive Sine Wave

LaTeX Go Power Drained = (Peak Voltage*Supply Voltage)/(pi*Load Resistance)

Peak Voltage of Positive Sine Wave

LaTeX Go Peak Voltage = (pi*Power Drained*Load Resistance)/Supply Voltage

Unity-Gain Bandwidth

LaTeX Go Unity Gain Bandwidth = Common Emitter Current Gain*3-dB Frequency

Transition Frequency

LaTeX Go Transition Frequency = 1/sqrt(Constant B)

Peak Voltage of Positive Sine Wave Formula

LaTeX Go

Peak Voltage = (pi*Power Drained*Load Resistance)/Supply Voltage
V_m = (pi*P*R_L)/V_i

What is a Class B amplifier?

Class B amplifier is a type of power amplifier where the active device (transistor) conducts only for the one-half cycle of the input signal. Since the active device is switched off for half the input cycle, the active device dissipates less power and hence the efficiency is improved.

How to Calculate Peak Voltage of Positive Sine Wave?

Peak Voltage of Positive Sine Wave calculator uses Peak Voltage = (pi*Power Drained*Load Resistance)/Supply Voltage to calculate the Peak Voltage, Peak Voltage of Positive Sine Wave refers to the maximum voltage reached during one complete cycle of the waveform when measured from the zero voltage reference point. Peak Voltage is denoted by V_m symbol.

How to calculate Peak Voltage of Positive Sine Wave using this online calculator? To use this online calculator for Peak Voltage of Positive Sine Wave, enter Power Drained (P), Load Resistance (R_L) & Supply Voltage (V_i) and hit the calculate button. Here is how the Peak Voltage of Positive Sine Wave calculation can be explained with given input values -> 5.984734 = (pi*0.00508*4500)/12.

FAQ

What is Peak Voltage of Positive Sine Wave?

Peak Voltage of Positive Sine Wave refers to the maximum voltage reached during one complete cycle of the waveform when measured from the zero voltage reference point and is represented as V_m = (pi*P*R_L)/V_i or Peak Voltage = (pi*Power Drained*Load Resistance)/Supply Voltage. Power Drained is the amount of energy liberated per second in a low frequency amplifier, Load resistance is the resistance value of load given for the network & Supply Voltage is the input voltage source which flows through the zener diode.

How to calculate Peak Voltage of Positive Sine Wave?

Peak Voltage of Positive Sine Wave refers to the maximum voltage reached during one complete cycle of the waveform when measured from the zero voltage reference point is calculated using Peak Voltage = (pi*Power Drained*Load Resistance)/Supply Voltage. To calculate Peak Voltage of Positive Sine Wave, you need Power Drained (P), Load Resistance (R_L) & Supply Voltage (V_i). With our tool, you need to enter the respective value for Power Drained, Load Resistance & Supply Voltage and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search