Overcut produced per side Calculator

✖Overcut Constant A is an empirical constant used in overcut calculations of EDM, its different for different materials at different voltages passing through it.ⓘ Overcut Constant A [A]			+10% -10%
✖Capacitance in Surface Defect is the ability of a component or circuit to store and collect energy in the form of an electrical charge.ⓘ Capacitance in Surface Defect [C_sd]			+10% -10%
✖Overcut Constant B is an empirical constant used to calculate overcut produced in the EDM process its different for different materials at different voltages passing through it.ⓘ Overcut Constant B [B]			+10% -10%

✖Overcut in mm per side is the overcut produced during EDM.ⓘ Overcut produced per side [O]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Unconventional machining processes Formula PDF PDF Image

Overcut produced per side Solution

STEP 0: Pre-Calculation Summary

Formula Used

Overcut in mm per side = (Overcut Constant A*Capacitance in Surface Defect^0.333)+Overcut Constant B
O = (A*C_sd^0.333)+B
This formula uses 4 Variables

Variables Used

Overcut in mm per side - Overcut in mm per side is the overcut produced during EDM.
Overcut Constant A - (Measured in Meter) - Overcut Constant A is an empirical constant used in overcut calculations of EDM, its different for different materials at different voltages passing through it.
Capacitance in Surface Defect - (Measured in Farad) - Capacitance in Surface Defect is the ability of a component or circuit to store and collect energy in the form of an electrical charge.
Overcut Constant B - (Measured in Meter) - Overcut Constant B is an empirical constant used to calculate overcut produced in the EDM process its different for different materials at different voltages passing through it.

STEP 1: Convert Input(s) to Base Unit

Overcut Constant A: 1.4 Meter --> 1.4 Meter No Conversion Required
Capacitance in Surface Defect: 5704165.41 Microfarad --> 5.70416541 Farad (Check conversion here)
Overcut Constant B: 2.5 Meter --> 2.5 Meter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

O = (A*C_sd^0.333)+B --> (1.4*5.70416541^0.333)+2.5

Evaluating ... ...

O = 4.99999999933264

STEP 3: Convert Result to Output's Unit

4.99999999933264 --> No Conversion Required

FINAL ANSWER

4.99999999933264 ≈ 5 <-- Overcut in mm per side

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Production Engineering » Unconventional machining processes » Electro Discharge Machining (EDM) » Possible surface defects in EDM » Overcut » Overcut produced per side

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Sai Venkata Phanindra Chary Arendra

Vallurupalli Nageswara Rao Vignana Jyothi Institute of Engineering and Technology (VNRVJIET), Hyderabad

Sai Venkata Phanindra Chary Arendra has verified this Calculator and 300+ more calculators!

< Overcut Calculators

Capacitance responsible for given overcut

LaTeX Go Capacitance in Surface Defect = ((Overcut in mm per side-Overcut Constant B)/Overcut Constant A)^(1/0.333)

Overcut produced per side

LaTeX Go Overcut in mm per side = (Overcut Constant A*Capacitance in Surface Defect^0.333)+Overcut Constant B

Overcut constant A

LaTeX Go Overcut Constant A = (Overcut in mm per side-Overcut Constant B)/Capacitance in Surface Defect^0.333

Overcut constant B

LaTeX Go Overcut Constant B = Overcut in mm per side-(Overcut Constant A*Capacitance in Surface Defect^0.333)

Overcut produced per side Formula

LaTeX Go

Overcut in mm per side = (Overcut Constant A*Capacitance in Surface Defect^0.333)+Overcut Constant B
O = (A*C_sd^0.333)+B

What factors affects surface finish during EDM ?

The amount of material removed and the surface finish produced is dependent upon the current in the spark. The material removed by the spark can be assumed to be a crater. The amount removed therefore will depend upon the crater depth, which is directly proportional to the current. Thus as the material removed increases and at the same time, the surface finish also decreases. However, decreasing the current in the spark, but increasing its frequency will improve the surface finish in view of the small crater size, but at the same time, the material removal rate can be maintained by increasing the frequency.

How to Calculate Overcut produced per side?

Overcut produced per side calculator uses Overcut in mm per side = (Overcut Constant A*Capacitance in Surface Defect^0.333)+Overcut Constant B to calculate the Overcut in mm per side, The Overcut produced per side formula is defined as the length of extra material removed due to side sparks in mm per side of electrode. Overcut in mm per side is denoted by O symbol.

How to calculate Overcut produced per side using this online calculator? To use this online calculator for Overcut produced per side, enter Overcut Constant A (A), Capacitance in Surface Defect (C_sd) & Overcut Constant B (B) and hit the calculate button. Here is how the Overcut produced per side calculation can be explained with given input values -> 5 = (1.4*5.70416541^0.333)+2.5.

FAQ

What is Overcut produced per side?

The Overcut produced per side formula is defined as the length of extra material removed due to side sparks in mm per side of electrode and is represented as O = (A*C_sd^0.333)+B or Overcut in mm per side = (Overcut Constant A*Capacitance in Surface Defect^0.333)+Overcut Constant B. Overcut Constant A is an empirical constant used in overcut calculations of EDM, its different for different materials at different voltages passing through it, Capacitance in Surface Defect is the ability of a component or circuit to store and collect energy in the form of an electrical charge & Overcut Constant B is an empirical constant used to calculate overcut produced in the EDM process its different for different materials at different voltages passing through it.

How to calculate Overcut produced per side?

The Overcut produced per side formula is defined as the length of extra material removed due to side sparks in mm per side of electrode is calculated using Overcut in mm per side = (Overcut Constant A*Capacitance in Surface Defect^0.333)+Overcut Constant B. To calculate Overcut produced per side, you need Overcut Constant A (A), Capacitance in Surface Defect (C_sd) & Overcut Constant B (B). With our tool, you need to enter the respective value for Overcut Constant A, Capacitance in Surface Defect & Overcut Constant B and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search