Overcut constant A Calculator

✖Overcut in mm per side is the overcut produced during EDM.ⓘ Overcut in mm per side [O]			+10% -10%
✖Overcut Constant B is an empirical constant used to calculate overcut produced in the EDM process its different for different materials at different voltages passing through it.ⓘ Overcut Constant B [B]			+10% -10%
✖Capacitance in Surface Defect is the ability of a component or circuit to store and collect energy in the form of an electrical charge.ⓘ Capacitance in Surface Defect [C_sd]			+10% -10%

✖Overcut Constant A is an empirical constant used in overcut calculations of EDM, its different for different materials at different voltages passing through it.ⓘ Overcut constant A [A]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Unconventional machining processes Formula PDF PDF Image

Overcut constant A Solution

STEP 0: Pre-Calculation Summary

Formula Used

Overcut Constant A = (Overcut in mm per side-Overcut Constant B)/Capacitance in Surface Defect^0.333
A = (O-B)/C_sd^0.333
This formula uses 4 Variables

Variables Used

Overcut Constant A - (Measured in Meter) - Overcut Constant A is an empirical constant used in overcut calculations of EDM, its different for different materials at different voltages passing through it.
Overcut in mm per side - Overcut in mm per side is the overcut produced during EDM.
Overcut Constant B - (Measured in Meter) - Overcut Constant B is an empirical constant used to calculate overcut produced in the EDM process its different for different materials at different voltages passing through it.
Capacitance in Surface Defect - (Measured in Farad) - Capacitance in Surface Defect is the ability of a component or circuit to store and collect energy in the form of an electrical charge.

STEP 1: Convert Input(s) to Base Unit

Overcut in mm per side: 5 --> No Conversion Required
Overcut Constant B: 2.5 Meter --> 2.5 Meter No Conversion Required
Capacitance in Surface Defect: 5704165.41 Microfarad --> 5.70416541 Farad (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

A = (O-B)/C_sd^0.333 --> (5-2.5)/5.70416541^0.333

Evaluating ... ...

A = 1.40000000037372

STEP 3: Convert Result to Output's Unit

1.40000000037372 Meter --> No Conversion Required

FINAL ANSWER

1.40000000037372 ≈ 1.4 Meter <-- Overcut Constant A

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Production Engineering » Unconventional machining processes » Electro Discharge Machining (EDM) » Possible surface defects in EDM » Overcut » Overcut constant A

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Sai Venkata Phanindra Chary Arendra

Vallurupalli Nageswara Rao Vignana Jyothi Institute of Engineering and Technology (VNRVJIET), Hyderabad

Sai Venkata Phanindra Chary Arendra has verified this Calculator and 300+ more calculators!

< Overcut Calculators

Capacitance responsible for given overcut

LaTeX Go Capacitance in Surface Defect = ((Overcut in mm per side-Overcut Constant B)/Overcut Constant A)^(1/0.333)

Overcut produced per side

LaTeX Go Overcut in mm per side = (Overcut Constant A*Capacitance in Surface Defect^0.333)+Overcut Constant B

Overcut constant A

LaTeX Go Overcut Constant A = (Overcut in mm per side-Overcut Constant B)/Capacitance in Surface Defect^0.333

Overcut constant B

LaTeX Go Overcut Constant B = Overcut in mm per side-(Overcut Constant A*Capacitance in Surface Defect^0.333)

Overcut constant A Formula

LaTeX Go

Overcut Constant A = (Overcut in mm per side-Overcut Constant B)/Capacitance in Surface Defect^0.333
A = (O-B)/C_sd^0.333

What factors affects surface finish during EDM ?

The amount of material removed and the surface finish produced is dependent upon the current in the spark. The material removed by the spark can be assumed to be a crater. The amount removed therefore will depend upon the crater depth, which is directly proportional to the current. Thus as the material removed increases and at the same time, the surface finish also decreases. However, decreasing the current in the spark, but increasing its frequency will improve the surface finish in view of the small crater size, but at the same time, the material removal rate can be maintained by increasing the frequency.

How to Calculate Overcut constant A?

Overcut constant A calculator uses Overcut Constant A = (Overcut in mm per side-Overcut Constant B)/Capacitance in Surface Defect^0.333 to calculate the Overcut Constant A, The Overcut constant A formula is defined as an empirical constant used in overcut calculations of EDM. Overcut Constant A is denoted by A symbol.

How to calculate Overcut constant A using this online calculator? To use this online calculator for Overcut constant A, enter Overcut in mm per side (O), Overcut Constant B (B) & Capacitance in Surface Defect (C_sd) and hit the calculate button. Here is how the Overcut constant A calculation can be explained with given input values -> 139.3907 = (5-2.5)/5.70416541^0.333.

FAQ

What is Overcut constant A?

The Overcut constant A formula is defined as an empirical constant used in overcut calculations of EDM and is represented as A = (O-B)/C_sd^0.333 or Overcut Constant A = (Overcut in mm per side-Overcut Constant B)/Capacitance in Surface Defect^0.333. Overcut in mm per side is the overcut produced during EDM, Overcut Constant B is an empirical constant used to calculate overcut produced in the EDM process its different for different materials at different voltages passing through it & Capacitance in Surface Defect is the ability of a component or circuit to store and collect energy in the form of an electrical charge.

How to calculate Overcut constant A?

The Overcut constant A formula is defined as an empirical constant used in overcut calculations of EDM is calculated using Overcut Constant A = (Overcut in mm per side-Overcut Constant B)/Capacitance in Surface Defect^0.333. To calculate Overcut constant A, you need Overcut in mm per side (O), Overcut Constant B (B) & Capacitance in Surface Defect (C_sd). With our tool, you need to enter the respective value for Overcut in mm per side, Overcut Constant B & Capacitance in Surface Defect and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search