Output Voltage of Controlled Source Transistor Calculator

✖Voltage gain is defined as the ratio of the output voltage to the input voltage.ⓘ Voltage Gain [A_v]			+10% -10%
✖Electric Current is the time rate of flow of charge through a cross sectional area.ⓘ Electric Current [i_t]			+10% -10%
✖Short circuit transconductance is the electrical characteristic relating the current through the output of a device to the voltage across the input of a device.ⓘ Short Circuit Transconductance [g'_m]			+10% -10%
✖Differential output signal is a measure of the voltage between two distinct output signals.ⓘ Differential Output Signal [V_od]			+10% -10%
✖Final Resistance is a measure of the opposition to current flow in an electrical circuit. Resistance is measured in ohms, symbolized by the Greek letter omega (Ω).ⓘ Final Resistance [R_final]			+10% -10%
✖Resistance of primary winding in secondary is the resistance that is available in primary winding of secondary.ⓘ Resistance of Primary Winding in Secondary [R₁]			+10% -10%

✖The DC Component of Gate to Source Voltage refers to the voltage applied between the gate and source terminals, which controls the flow of current between the drain and source terminals.ⓘ Output Voltage of Controlled Source Transistor [V_gsq]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Transistor Amplifiers Formula PDF PDF Image

Output Voltage of Controlled Source Transistor Solution

STEP 0: Pre-Calculation Summary

Formula Used

DC Component of Gate to Source Voltage = (Voltage Gain*Electric Current-Short Circuit Transconductance*Differential Output Signal)*(1/Final Resistance+1/Resistance of Primary Winding in Secondary)
V_gsq = (A_v*i_t-g'_m*V_od)*(1/R_final+1/R₁)
This formula uses 7 Variables

Variables Used

DC Component of Gate to Source Voltage - (Measured in Volt) - The DC Component of Gate to Source Voltage refers to the voltage applied between the gate and source terminals, which controls the flow of current between the drain and source terminals.
Voltage Gain - Voltage gain is defined as the ratio of the output voltage to the input voltage.
Electric Current - (Measured in Ampere) - Electric Current is the time rate of flow of charge through a cross sectional area.
Short Circuit Transconductance - (Measured in Siemens) - Short circuit transconductance is the electrical characteristic relating the current through the output of a device to the voltage across the input of a device.
Differential Output Signal - (Measured in Volt) - Differential output signal is a measure of the voltage between two distinct output signals.
Final Resistance - (Measured in Ohm) - Final Resistance is a measure of the opposition to current flow in an electrical circuit. Resistance is measured in ohms, symbolized by the Greek letter omega (Ω).
Resistance of Primary Winding in Secondary - (Measured in Ohm) - Resistance of primary winding in secondary is the resistance that is available in primary winding of secondary.

STEP 1: Convert Input(s) to Base Unit

Voltage Gain: 4.21 --> No Conversion Required
Electric Current: 4402 Milliampere --> 4.402 Ampere (Check conversion here)
Short Circuit Transconductance: 2.5 Millisiemens --> 0.0025 Siemens (Check conversion here)
Differential Output Signal: 100.3 Volt --> 100.3 Volt No Conversion Required
Final Resistance: 0.00243 Kilohm --> 2.43 Ohm (Check conversion here)
Resistance of Primary Winding in Secondary: 0.0071 Kilohm --> 7.1 Ohm (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

V_gsq = (A_v*i_t-g'_m*V_od)*(1/R_final+1/R₁) --> (4.21*4.402-0.0025*100.3)*(1/2.43+1/7.1)

Evaluating ... ...

V_gsq = 10.0982040862459

STEP 3: Convert Result to Output's Unit

10.0982040862459 Volt --> No Conversion Required

FINAL ANSWER

10.0982040862459 ≈ 10.0982 Volt <-- DC Component of Gate to Source Voltage

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electronics » Amplifiers » Transistor Amplifiers » Common Source Amplifier » Output Voltage of Controlled Source Transistor

Credits

Created by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has created this Calculator and 600+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Common Source Amplifier Calculators

Overall Feedback Voltage Gain of Common-Source Amplifier

LaTeX Go Feedback Voltage Gain = -MOSFET Primary Transconductance*(Input Resistance/(Input Resistance+Signal Resistance))*(1/Drain Resistance+1/Load Resistance+1/Finite Output Resistance)^-1

Open-Circuit Voltage Gain of CS Amplifier

LaTeX Go Open Circuit Voltage Gain = Finite Output Resistance/(Finite Output Resistance+1/MOSFET Primary Transconductance)

Current Gain of Controlled Source Transistor

LaTeX Go Current Gain = 1/(1+1/(MOSFET Primary Transconductance*Resistance between Drain and Ground))

Total Voltage Gain of CS Amplifier

LaTeX Go Voltage Gain = Load Voltage/Input Voltage

< CV Actions of Common Stage Amplifiers Calculators

Input Resistance of Common Emitter Amplifier

LaTeX Go Input Resistance = (1/Base Resistance+1/Base Resistance 2+1/Small Signal Input Resistance)^-1

Input Impedance of Common-Base Amplifier

LaTeX Go Input Impedance = (1/Emitter Resistance+1/Small Signal Input Resistance)^(-1)

Fundamental Voltage in Common-Emitter Amplifier

LaTeX Go Fundamental Component Voltage = Input Resistance*Base Current

Emitter Current of Common-Base Amplifier

LaTeX Go Emitter Current = Input Voltage/Emitter Resistance

Output Voltage of Controlled Source Transistor Formula

LaTeX Go

How do you control voltage in a circuit?

To reduce the voltage in half, we simply form a voltage divider circuit between 2 resistors of equal value (for example, 2 10KΩ) resistors. To divide voltage in half, all you must do is place any 2 resistors of equal value in series and then place a jumper wire in between the resistors.

How to Calculate Output Voltage of Controlled Source Transistor?

Output Voltage of Controlled Source Transistor calculator uses DC Component of Gate to Source Voltage = (Voltage Gain*Electric Current-Short Circuit Transconductance*Differential Output Signal)*(1/Final Resistance+1/Resistance of Primary Winding in Secondary) to calculate the DC Component of Gate to Source Voltage, The Output voltage of controlled source transistor formula is defined as the voltage that is controlled by a voltage elsewhere in a circuit. In practice, a VCVS is often used in modeling operational amplifiers (op-amps), and can also be used in modeling a voltage signal chain more generally. DC Component of Gate to Source Voltage is denoted by V_gsq symbol.

How to calculate Output Voltage of Controlled Source Transistor using this online calculator? To use this online calculator for Output Voltage of Controlled Source Transistor, enter Voltage Gain (A_v), Electric Current (i_t), Short Circuit Transconductance (g'_m), Differential Output Signal (V_od), Final Resistance (R_final) & Resistance of Primary Winding in Secondary (R₁) and hit the calculate button. Here is how the Output Voltage of Controlled Source Transistor calculation can be explained with given input values -> 2.589591 = (4.21*4.402-0.0025*100.3)*(1/2.43+1/7.1).

FAQ

What is Output Voltage of Controlled Source Transistor?

The Output voltage of controlled source transistor formula is defined as the voltage that is controlled by a voltage elsewhere in a circuit. In practice, a VCVS is often used in modeling operational amplifiers (op-amps), and can also be used in modeling a voltage signal chain more generally and is represented as V_gsq = (A_v*i_t-g'_m*V_od)*(1/R_final+1/R₁) or DC Component of Gate to Source Voltage = (Voltage Gain*Electric Current-Short Circuit Transconductance*Differential Output Signal)*(1/Final Resistance+1/Resistance of Primary Winding in Secondary). Voltage gain is defined as the ratio of the output voltage to the input voltage, Electric Current is the time rate of flow of charge through a cross sectional area, Short circuit transconductance is the electrical characteristic relating the current through the output of a device to the voltage across the input of a device, Differential output signal is a measure of the voltage between two distinct output signals, Final Resistance is a measure of the opposition to current flow in an electrical circuit. Resistance is measured in ohms, symbolized by the Greek letter omega (Ω) & Resistance of primary winding in secondary is the resistance that is available in primary winding of secondary.

How to calculate Output Voltage of Controlled Source Transistor?

The Output voltage of controlled source transistor formula is defined as the voltage that is controlled by a voltage elsewhere in a circuit. In practice, a VCVS is often used in modeling operational amplifiers (op-amps), and can also be used in modeling a voltage signal chain more generally is calculated using DC Component of Gate to Source Voltage = (Voltage Gain*Electric Current-Short Circuit Transconductance*Differential Output Signal)*(1/Final Resistance+1/Resistance of Primary Winding in Secondary). To calculate Output Voltage of Controlled Source Transistor, you need Voltage Gain (A_v), Electric Current (i_t), Short Circuit Transconductance (g'_m), Differential Output Signal (V_od), Final Resistance (R_final) & Resistance of Primary Winding in Secondary (R₁). With our tool, you need to enter the respective value for Voltage Gain, Electric Current, Short Circuit Transconductance, Differential Output Signal, Final Resistance & Resistance of Primary Winding in Secondary and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search