Number of Positive Peak Calculator

✖Vertical Frequency is defined as vertical scan frequency is the number of times a cathode ray tube was redrawn per second.ⓘ Vertical Frequency [F_v]			+10% -10%
✖Right Hand Side Peak Number represent leading edges or rising edges of pulses or signals. These edges can be important in digital signal analysis and timing measurements.ⓘ Right Hand Side Peak Number [P_n]			+10% -10%
✖Horizontal Frequency usually expressed in kilohertz is the number of times per second that a raster-scan video system transmits or displays a complete horizontal line.ⓘ Horizontal Frequency [F_h]			+10% -10%

✖Positive Peak Number refers to the count or frequency of positive voltage peaks in an electrical signal being measured It occurs when the voltage of the waveform reaches its highest value.ⓘ Number of Positive Peak [N_p]

⎘ Copy

👎

Formula

✖

Number of Positive Peak

Formula

`"N"_{"p"} = ("F"_{"v"}*"P"_{"n"})/"F"_{"h"}`

Example

`"4.583333"=("6.25Hz"*"2.2")/"3Hz"`

Calculator

LaTeX

Reset

👍

Download Electronics and Instrumentation Formula PDF PDF Image

Number of Positive Peak Solution

STEP 0: Pre-Calculation Summary

Formula Used

Positive Peak Number = (Vertical Frequency*Right Hand Side Peak Number)/Horizontal Frequency
N_p = (F_v*P_n)/F_h
This formula uses 4 Variables

Variables Used

Positive Peak Number - Positive Peak Number refers to the count or frequency of positive voltage peaks in an electrical signal being measured It occurs when the voltage of the waveform reaches its highest value.
Vertical Frequency - (Measured in Hertz) - Vertical Frequency is defined as vertical scan frequency is the number of times a cathode ray tube was redrawn per second.
Right Hand Side Peak Number - Right Hand Side Peak Number represent leading edges or rising edges of pulses or signals. These edges can be important in digital signal analysis and timing measurements.
Horizontal Frequency - (Measured in Hertz) - Horizontal Frequency usually expressed in kilohertz is the number of times per second that a raster-scan video system transmits or displays a complete horizontal line.

STEP 1: Convert Input(s) to Base Unit

Vertical Frequency: 6.25 Hertz --> 6.25 Hertz No Conversion Required
Right Hand Side Peak Number: 2.2 --> No Conversion Required
Horizontal Frequency: 3 Hertz --> 3 Hertz No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

N_p = (F_v*P_n)/F_h --> (6.25*2.2)/3

Evaluating ... ...

N_p = 4.58333333333333

STEP 3: Convert Result to Output's Unit

4.58333333333333 --> No Conversion Required

FINAL ANSWER

4.58333333333333 ≈ 4.583333 <-- Positive Peak Number

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electronics and Instrumentation » Signal Generator & Analyzer » Oscilloscope » Number of Positive Peak

Credits

Created by Shobhit Dimri

Bipin Tripathi Kumaon Institute of Technology (BTKIT), Dwarahat

Shobhit Dimri has created this Calculator and 900+ more calculators!

Verified by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has verified this Calculator and 1900+ more calculators!

< 25 Oscilloscope Calculators

Modulus Number of Counter

Go Counter Number = log(Counter Modulus Number,(Output Time Period/Oscillation Time Period))

Display Rise Time of Oscilloscope

Go Oscilloscope Display Rise Time = sqrt(Input Pulse Rise Time^2-Oscilloscope Imposed Rise Time^2)

Rise Time Imposed by Oscilloscope

Go Oscilloscope Imposed Rise Time = sqrt(Input Pulse Rise Time^2-Oscilloscope Display Rise Time^2)

Rise Time of Oscilloscope

Go Input Pulse Rise Time = sqrt(Oscilloscope Display Rise Time^2+Oscilloscope Imposed Rise Time^2)

Number of Right Hand Side Peak

Go Right Hand Side Peak Number = (Horizontal Frequency*Positive Peak Number)/Vertical Frequency

Number of Positive Peak

Go Positive Peak Number = (Vertical Frequency*Right Hand Side Peak Number)/Horizontal Frequency

Vertical Frequency

Go Vertical Frequency = (Horizontal Frequency*Positive Peak Number)/Right Hand Side Peak Number

Oscillation Time Period

Go Oscillation Time Period = Output Time Period/(Counter Modulus Number^Counter Number)

Output Time Period

Go Output Time Period = Oscillation Time Period*Counter Modulus Number^Counter Number

Unknown Frequency using Lissajous Figures

Go Unknown Frequency = (Known Frequency*Horizontal Tangencies)/Vertical Tangencies

Time Per Division of Oscilloscope

Go Time per Division = Progressive Wave Time Period/Horizontal Division per Cycle

Horizontal Division Per Cycle

Go Horizontal Division per Cycle = Progressive Wave Time Period/Time per Division

Time Period of Waveform

Go Progressive Wave Time Period = Horizontal Division per Cycle*Time per Division

Deflection Sensitivity

Go Deflection Sensitivity = Deflection on Screen*Electric Potential Difference

Deflection on Screen

Go Deflection on Screen = Deflection Sensitivity/Electric Potential Difference

Phase Difference between Two Sine Wave

Go Phase Difference = Phase Difference in Division*Degree per Division

Phase Difference in Division

Go Phase Difference in Division = Phase Difference/Degree per Division

Degree Per Division

Go Degree per Division = Phase Difference/Phase Difference in Division

Peak to Peak Voltage of Waveform

Go Peak Voltage = Voltage per Division*Vertical Peak to Peak Division

Vertical Peak to Peak Division

Go Vertical Peak to Peak Division = Peak Voltage/Voltage per Division

Number of Gaps in Circle

Go Gaps Number in Circle = Modulating Frequency Ratio*Length

Length of Oscilloscope

Go Length = Gaps Number in Circle/Modulating Frequency Ratio

Pulse Width of Oscilloscope

Go Oscilloscope Pulse Width = 2.2*Resistance*Capacitance

Time Constant of Oscilloscope

Go Time Constant = Resistance*Capacitance

Deflection Factor

Go Deflection Factor = 1/Deflection Sensitivity

Number of Positive Peak Formula

Positive Peak Number = (Vertical Frequency*Right Hand Side Peak Number)/Horizontal Frequency
N_p = (F_v*P_n)/F_h

What is vertical refresh rate?

The refresh rate (or "vertical refresh rate", "vertical scan rate", terminology originating with the cathode ray tubes) is the number of times per second that a raster-based display device displays a new image.

How to Calculate Number of Positive Peak?

Number of Positive Peak calculator uses Positive Peak Number = (Vertical Frequency*Right Hand Side Peak Number)/Horizontal Frequency to calculate the Positive Peak Number, The Number of Positive Peak formula is defined as the count of maximum points above the baseline in a given waveform within a specified time period. Positive Peak Number is denoted by N_p symbol.

How to calculate Number of Positive Peak using this online calculator? To use this online calculator for Number of Positive Peak, enter Vertical Frequency (F_v), Right Hand Side Peak Number (P_n) & Horizontal Frequency (F_h) and hit the calculate button. Here is how the Number of Positive Peak calculation can be explained with given input values -> 4.583333 = (6.25*2.2)/3.

FAQ

What is Number of Positive Peak?

The Number of Positive Peak formula is defined as the count of maximum points above the baseline in a given waveform within a specified time period and is represented as N_p = (F_v*P_n)/F_h or Positive Peak Number = (Vertical Frequency*Right Hand Side Peak Number)/Horizontal Frequency. Vertical Frequency is defined as vertical scan frequency is the number of times a cathode ray tube was redrawn per second, Right Hand Side Peak Number represent leading edges or rising edges of pulses or signals. These edges can be important in digital signal analysis and timing measurements & Horizontal Frequency usually expressed in kilohertz is the number of times per second that a raster-scan video system transmits or displays a complete horizontal line.

How to calculate Number of Positive Peak?

The Number of Positive Peak formula is defined as the count of maximum points above the baseline in a given waveform within a specified time period is calculated using Positive Peak Number = (Vertical Frequency*Right Hand Side Peak Number)/Horizontal Frequency. To calculate Number of Positive Peak, you need Vertical Frequency (F_v), Right Hand Side Peak Number (P_n) & Horizontal Frequency (F_h). With our tool, you need to enter the respective value for Vertical Frequency, Right Hand Side Peak Number & Horizontal Frequency and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search