Nominal Tensile Stress in Round Shaft with Shoulder Fillet Calculator

✖The Load on Flat Plate is the force applied uniformly across a flat surface, affecting the plate's structural integrity and performance under various loading conditions.ⓘ Load on Flat Plate [P]			+10% -10%
✖The Smaller Diameter of Shaft with Fillet is the reduced diameter at the fillet radius, which influences stress concentration and overall strength in mechanical design.ⓘ Smaller Diameter of Shaft with Fillet [d_small]			+10% -10%

✖The Nominal Stress is the average stress experienced by a material under load, used to assess its performance and safety in mechanical design applications.ⓘ Nominal Tensile Stress in Round Shaft with Shoulder Fillet [σ_o]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Mechanical Formula PDF PDF Image

Nominal Tensile Stress in Round Shaft with Shoulder Fillet Solution

STEP 0: Pre-Calculation Summary

Formula Used

Nominal Stress = (4*Load on Flat Plate)/(pi*Smaller Diameter of Shaft with Fillet^2)
σ_o = (4*P)/(pi*d_small^2)
This formula uses 1 Constants, 3 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Variables Used

Nominal Stress - (Measured in Pascal) - The Nominal Stress is the average stress experienced by a material under load, used to assess its performance and safety in mechanical design applications.
Load on Flat Plate - (Measured in Newton) - The Load on Flat Plate is the force applied uniformly across a flat surface, affecting the plate's structural integrity and performance under various loading conditions.
Smaller Diameter of Shaft with Fillet - (Measured in Meter) - The Smaller Diameter of Shaft with Fillet is the reduced diameter at the fillet radius, which influences stress concentration and overall strength in mechanical design.

STEP 1: Convert Input(s) to Base Unit

Load on Flat Plate: 8750 Newton --> 8750 Newton No Conversion Required
Smaller Diameter of Shaft with Fillet: 21.11004 Millimeter --> 0.02111004 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

σ_o = (4*P)/(pi*d_small^2) --> (4*8750)/(pi*0.02111004^2)

Evaluating ... ...

σ_o = 25000002.9090987

STEP 3: Convert Result to Output's Unit

25000002.9090987 Pascal -->25.0000029090987 Newton per Square Millimeter (Check conversion here)

FINAL ANSWER

25.0000029090987 ≈ 25 Newton per Square Millimeter <-- Nominal Stress

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Mechanical » Machine Design » Design against Fluctuating Load » Stress Concentration Factors in Design » Round Shaft against Fluctuating Loads » Nominal Tensile Stress in Round Shaft with Shoulder Fillet

Credits

Created by Saurabh Patil

Shri Govindram Seksaria Institute of Technology and Science (SGSITS ), Indore

Saurabh Patil has created this Calculator and 700+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Round Shaft against Fluctuating Loads Calculators

Nominal Torsional Stress in Round Shaft with Shoulder Fillet

LaTeX Go Nominal Stress = (16*Torsional Moment on Round Shaft)/(pi*Smaller Diameter of Shaft with Fillet^3)

Nominal Bending Stress in Round Shaft with Shoulder Fillet

LaTeX Go Nominal Stress = (32*Bending Moment on Round Shaft)/(pi*Smaller Diameter of Shaft with Fillet^3)

Bending Moment in Round Shaft with Shoulder Fillet given Nominal Stress

LaTeX Go Bending Moment on Round Shaft = (Nominal Stress*pi*Smaller Diameter of Shaft with Fillet^3)/32

Nominal Tensile Stress in Round Shaft with Shoulder Fillet

LaTeX Go Nominal Stress = (4*Load on Flat Plate)/(pi*Smaller Diameter of Shaft with Fillet^2)

Nominal Tensile Stress in Round Shaft with Shoulder Fillet Formula

LaTeX Go

Nominal Stress = (4*Load on Flat Plate)/(pi*Smaller Diameter of Shaft with Fillet^2)
σ_o = (4*P)/(pi*d_small^2)

Some load applications that may cause stress concentration

The examples of these load applications are as follows:
(a) Contact between the meshing teeth of the driving and the driven gear.
(b) Contact between the cam and the follower.
(c) Contact between the balls and the races of ball bearing.
(d) Contact between the rail and the wheel.
(e) Contact between the crane hook and the chain.
In all these cases, the concentrated load is applied over a very small area resulting in stress
concentration.

How to Calculate Nominal Tensile Stress in Round Shaft with Shoulder Fillet?

Nominal Tensile Stress in Round Shaft with Shoulder Fillet calculator uses Nominal Stress = (4*Load on Flat Plate)/(pi*Smaller Diameter of Shaft with Fillet^2) to calculate the Nominal Stress, Nominal Tensile Stress in Round shaft with Shoulder fillet is fhe amount of tensile stress at the minimum cross section in round shaft with shoulder fillet with stress concentration arising due to the forces acting parallel to the shaft axis. Nominal Stress is denoted by σ_o symbol.

How to calculate Nominal Tensile Stress in Round Shaft with Shoulder Fillet using this online calculator? To use this online calculator for Nominal Tensile Stress in Round Shaft with Shoulder Fillet, enter Load on Flat Plate (P) & Smaller Diameter of Shaft with Fillet (d_small) and hit the calculate button. Here is how the Nominal Tensile Stress in Round Shaft with Shoulder Fillet calculation can be explained with given input values -> 3.4E-5 = (4*8750)/(pi*0.02111004^2).

FAQ

What is Nominal Tensile Stress in Round Shaft with Shoulder Fillet?

Nominal Tensile Stress in Round shaft with Shoulder fillet is fhe amount of tensile stress at the minimum cross section in round shaft with shoulder fillet with stress concentration arising due to the forces acting parallel to the shaft axis and is represented as σ_o = (4*P)/(pi*d_small^2) or Nominal Stress = (4*Load on Flat Plate)/(pi*Smaller Diameter of Shaft with Fillet^2). The Load on Flat Plate is the force applied uniformly across a flat surface, affecting the plate's structural integrity and performance under various loading conditions & The Smaller Diameter of Shaft with Fillet is the reduced diameter at the fillet radius, which influences stress concentration and overall strength in mechanical design.

How to calculate Nominal Tensile Stress in Round Shaft with Shoulder Fillet?

Nominal Tensile Stress in Round shaft with Shoulder fillet is fhe amount of tensile stress at the minimum cross section in round shaft with shoulder fillet with stress concentration arising due to the forces acting parallel to the shaft axis is calculated using Nominal Stress = (4*Load on Flat Plate)/(pi*Smaller Diameter of Shaft with Fillet^2). To calculate Nominal Tensile Stress in Round Shaft with Shoulder Fillet, you need Load on Flat Plate (P) & Smaller Diameter of Shaft with Fillet (d_small). With our tool, you need to enter the respective value for Load on Flat Plate & Smaller Diameter of Shaft with Fillet and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Nominal Stress?

In this formula, Nominal Stress uses Load on Flat Plate & Smaller Diameter of Shaft with Fillet. We can use 2 other way(s) to calculate the same, which is/are as follows -

Nominal Stress = (32*Bending Moment on Round Shaft)/(pi*Smaller Diameter of Shaft with Fillet^3)
Nominal Stress = (16*Torsional Moment on Round Shaft)/(pi*Smaller Diameter of Shaft with Fillet^3)

Home

FREE PDFs

🔍 Search