Negative Half of Maximum Power Dissipation in Class B Stage Solution

STEP 0: Pre-Calculation Summary
Formula Used
Negative Maximum Power Dissipation = Supply Voltage^2/(pi^2*Load Resistance)
PDNmax = Vcc^2/(pi^2*RL)
This formula uses 1 Constants, 3 Variables
Constants Used
pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288
Variables Used
Negative Maximum Power Dissipation - (Measured in Watt) - Negative Maximum Power Dissipation Load Power is defined as the power absorbed by the load connected in the negative region to the transistor circuit for class B.
Supply Voltage - (Measured in Volt) - Supply Voltage is also defined defined as the bias voltage applied to the op amp for Q2(transistor 2) pin. It is also defined as as voltage at collector.
Load Resistance - (Measured in Ohm) - Load Resistance is defined as the cumulative resistance of a circuit as seen by the voltage, current or power source driving that circuit.
STEP 1: Convert Input(s) to Base Unit
Supply Voltage: 7.52 Volt --> 7.52 Volt No Conversion Required
Load Resistance: 2.5 Kilohm --> 2500 Ohm (Check conversion ​here)
STEP 2: Evaluate Formula
Substituting Input Values in Formula
PDNmax = Vcc^2/(pi^2*RL) --> 7.52^2/(pi^2*2500)
Evaluating ... ...
PDNmax = 0.00229190138537906
STEP 3: Convert Result to Output's Unit
0.00229190138537906 Watt -->2.29190138537906 Milliwatt (Check conversion ​here)
FINAL ANSWER
2.29190138537906 2.291901 Milliwatt <-- Negative Maximum Power Dissipation
(Calculation completed in 00.020 seconds)

Credits

Creator Image
Created by Payal Priya
Birsa Institute of Technology (BIT), Sindri
Payal Priya has created this Calculator and 600+ more calculators!
Verifier Image
Verified by Anshika Arya
National Institute Of Technology (NIT), Hamirpur
Anshika Arya has verified this Calculator and 2500+ more calculators!

Class B Output Stage Calculators

Load Resistance of Class B Stage
​ LaTeX ​ Go Load Resistance of Class B = (2*Peak Amplitude Voltage*Supply Voltage)/(pi*Supply Power)
Efficiency of Class B Output Stage
​ LaTeX ​ Go Efficiency of Class B = pi/4*(Peak Amplitude Voltage/Supply Voltage)
Maximum Average Power from Class B Output Stage
​ LaTeX ​ Go Maximum Power in Class B = 1/2*(Supply Voltage^2/Load Resistance)
Efficiency of Class A
​ LaTeX ​ Go Efficiency of Class A = 1/2*(Output Voltage/Drain Voltage)

Negative Half of Maximum Power Dissipation in Class B Stage Formula

​LaTeX ​Go
Negative Maximum Power Dissipation = Supply Voltage^2/(pi^2*Load Resistance)
PDNmax = Vcc^2/(pi^2*RL)

What is a Class B amplifier?

Class B amplifier is a type of power amplifier where the active device (transistor) conducts only for the one-half cycle of the input signal. Since the active device is switched off for half the input cycle, the active device dissipates less power and hence the efficiency is improved.

How to Calculate Negative Half of Maximum Power Dissipation in Class B Stage?

Negative Half of Maximum Power Dissipation in Class B Stage calculator uses Negative Maximum Power Dissipation = Supply Voltage^2/(pi^2*Load Resistance) to calculate the Negative Maximum Power Dissipation, The Negative half of maximum power dissipation in class B stage formula refers to the maximum power that a device can dissipate without causing damage or failure. It is calculated to ensure safe operation and prevent overheating. Negative Maximum Power Dissipation is denoted by PDNmax symbol.

How to calculate Negative Half of Maximum Power Dissipation in Class B Stage using this online calculator? To use this online calculator for Negative Half of Maximum Power Dissipation in Class B Stage, enter Supply Voltage (Vcc) & Load Resistance (RL) and hit the calculate button. Here is how the Negative Half of Maximum Power Dissipation in Class B Stage calculation can be explained with given input values -> 2279.727 = 7.52^2/(pi^2*2500).

FAQ

What is Negative Half of Maximum Power Dissipation in Class B Stage?
The Negative half of maximum power dissipation in class B stage formula refers to the maximum power that a device can dissipate without causing damage or failure. It is calculated to ensure safe operation and prevent overheating and is represented as PDNmax = Vcc^2/(pi^2*RL) or Negative Maximum Power Dissipation = Supply Voltage^2/(pi^2*Load Resistance). Supply Voltage is also defined defined as the bias voltage applied to the op amp for Q2(transistor 2) pin. It is also defined as as voltage at collector & Load Resistance is defined as the cumulative resistance of a circuit as seen by the voltage, current or power source driving that circuit.
How to calculate Negative Half of Maximum Power Dissipation in Class B Stage?
The Negative half of maximum power dissipation in class B stage formula refers to the maximum power that a device can dissipate without causing damage or failure. It is calculated to ensure safe operation and prevent overheating is calculated using Negative Maximum Power Dissipation = Supply Voltage^2/(pi^2*Load Resistance). To calculate Negative Half of Maximum Power Dissipation in Class B Stage, you need Supply Voltage (Vcc) & Load Resistance (RL). With our tool, you need to enter the respective value for Supply Voltage & Load Resistance and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!