Maximum Voltage using Load Current (1 Phase 3 Wire US) Calculator

✖Power Transmitted is the amount of power that is transferred from its place of generation to a location where it is applied to perform useful work.ⓘ Power Transmitted [P]			+10% -10%
✖Phase Difference is defined as the difference between the phasor of apparent and real power (in degrees) or between voltage and current in an ac circuit.ⓘ Phase Difference [Φ]			+10% -10%
✖Current Underground AC is defined as the current flowing through the overhead ac supply wire.ⓘ Current Underground AC [I]			+10% -10%

✖Maximum Voltage Underground AC is defined as the peak amplitude of the AC voltage supplied to the line or wire.ⓘ Maximum Voltage using Load Current (1 Phase 3 Wire US) [V_m]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Power System Formula PDF PDF Image

Maximum Voltage using Load Current (1 Phase 3 Wire US) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Maximum Voltage Underground AC = sqrt(2)*Power Transmitted/(cos(Phase Difference)*Current Underground AC)
V_m = sqrt(2)*P/(cos(Φ)*I)
This formula uses 2 Functions, 4 Variables

Functions Used

cos - Cosine of an angle is the ratio of the side adjacent to the angle to the hypotenuse of the triangle., cos(Angle)
sqrt - A square root function is a function that takes a non-negative number as an input and returns the square root of the given input number., sqrt(Number)

Variables Used

Maximum Voltage Underground AC - (Measured in Volt) - Maximum Voltage Underground AC is defined as the peak amplitude of the AC voltage supplied to the line or wire.
Power Transmitted - (Measured in Watt) - Power Transmitted is the amount of power that is transferred from its place of generation to a location where it is applied to perform useful work.
Phase Difference - (Measured in Radian) - Phase Difference is defined as the difference between the phasor of apparent and real power (in degrees) or between voltage and current in an ac circuit.
Current Underground AC - (Measured in Ampere) - Current Underground AC is defined as the current flowing through the overhead ac supply wire.

STEP 1: Convert Input(s) to Base Unit

Power Transmitted: 300 Watt --> 300 Watt No Conversion Required
Phase Difference: 30 Degree --> 0.5235987755982 Radian (Check conversion here)
Current Underground AC: 9 Ampere --> 9 Ampere No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

V_m = sqrt(2)*P/(cos(Φ)*I) --> sqrt(2)*300/(cos(0.5235987755982)*9)

Evaluating ... ...

V_m = 54.4331053951817

STEP 3: Convert Result to Output's Unit

54.4331053951817 Volt --> No Conversion Required

FINAL ANSWER

54.4331053951817 ≈ 54.43311 Volt <-- Maximum Voltage Underground AC

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Power System » Underground AC Supply » 1 Φ 3 Wire System » Current and Voltage » Maximum Voltage using Load Current (1 Phase 3 Wire US)

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Kethavath Srinath

Osmania University (OU), Hyderabad

Kethavath Srinath has verified this Calculator and 1200+ more calculators!

< Current and Voltage Calculators

Maximum Voltage using Volume of Conductor Material(1 Phase 3 Wire US)

LaTeX Go Maximum Voltage Underground AC = sqrt(10*Resistivity*(Power Transmitted*Length of Underground AC Wire)^2/(Line Losses*Volume Of Conductor*(cos(Phase Difference))^2))

RMS Voltage using Volume of Conductor Material(1 Phase 3 Wire US)

LaTeX Go Root Mean Square Voltage = sqrt(5*Resistivity*((Power Transmitted*Length of Underground AC Wire)^2)/(Line Losses*Volume Of Conductor*((cos(Phase Difference))^2)))

Maximum Voltage using Load Current (1 Phase 3 Wire US)

LaTeX Go Maximum Voltage Underground AC = sqrt(2)*Power Transmitted/(cos(Phase Difference)*Current Underground AC)

RMS Voltage using Load Current (1 Phase 3 Wire US)

LaTeX Go Root Mean Square Voltage = sqrt(2)*Power Transmitted/(cos(Phase Difference)*Current Underground AC)

Maximum Voltage using Load Current (1 Phase 3 Wire US) Formula

LaTeX Go

Maximum Voltage Underground AC = sqrt(2)*Power Transmitted/(cos(Phase Difference)*Current Underground AC)
V_m = sqrt(2)*P/(cos(Φ)*I)

What is a single phase 3 wire system?

Single-phase three-wire is also a term used to describe a system where the center of the phase is earthed rather than either end. This means that the largest voltage-to-earth fault experienced will be half the output voltage. It is commonly used when working with power tools in especially wet or 'rough' environments.

How to Calculate Maximum Voltage using Load Current (1 Phase 3 Wire US)?

Maximum Voltage using Load Current (1 Phase 3 Wire US) calculator uses Maximum Voltage Underground AC = sqrt(2)*Power Transmitted/(cos(Phase Difference)*Current Underground AC) to calculate the Maximum Voltage Underground AC, The Maximum Voltage using Load Current (1 phase 3 wire US) formula is defined as the highest voltage rating for electrical devices and equipment that can be used with the voltage definition. Maximum Voltage Underground AC is denoted by V_m symbol.

How to calculate Maximum Voltage using Load Current (1 Phase 3 Wire US) using this online calculator? To use this online calculator for Maximum Voltage using Load Current (1 Phase 3 Wire US), enter Power Transmitted (P), Phase Difference (Φ) & Current Underground AC (I) and hit the calculate button. Here is how the Maximum Voltage using Load Current (1 Phase 3 Wire US) calculation can be explained with given input values -> 54.43311 = sqrt(2)*300/(cos(0.5235987755982)*9).

FAQ

What is Maximum Voltage using Load Current (1 Phase 3 Wire US)?

The Maximum Voltage using Load Current (1 phase 3 wire US) formula is defined as the highest voltage rating for electrical devices and equipment that can be used with the voltage definition and is represented as V_m = sqrt(2)*P/(cos(Φ)*I) or Maximum Voltage Underground AC = sqrt(2)*Power Transmitted/(cos(Phase Difference)*Current Underground AC). Power Transmitted is the amount of power that is transferred from its place of generation to a location where it is applied to perform useful work, Phase Difference is defined as the difference between the phasor of apparent and real power (in degrees) or between voltage and current in an ac circuit & Current Underground AC is defined as the current flowing through the overhead ac supply wire.

How to calculate Maximum Voltage using Load Current (1 Phase 3 Wire US)?

The Maximum Voltage using Load Current (1 phase 3 wire US) formula is defined as the highest voltage rating for electrical devices and equipment that can be used with the voltage definition is calculated using Maximum Voltage Underground AC = sqrt(2)*Power Transmitted/(cos(Phase Difference)*Current Underground AC). To calculate Maximum Voltage using Load Current (1 Phase 3 Wire US), you need Power Transmitted (P), Phase Difference (Φ) & Current Underground AC (I). With our tool, you need to enter the respective value for Power Transmitted, Phase Difference & Current Underground AC and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Maximum Voltage Underground AC?

In this formula, Maximum Voltage Underground AC uses Power Transmitted, Phase Difference & Current Underground AC. We can use 3 other way(s) to calculate the same, which is/are as follows -

Maximum Voltage Underground AC = sqrt(10*Resistivity*(Power Transmitted*Length of Underground AC Wire)^2/(Line Losses*Volume Of Conductor*(cos(Phase Difference))^2))
Maximum Voltage Underground AC = (2*Power Transmitted/cos(Phase Difference))*sqrt(Resistivity*Length of Underground AC Wire/(Line Losses*Area of Underground AC Wire))
Maximum Voltage Underground AC = (2*Power Transmitted/cos(Phase Difference))*sqrt(Resistance Underground AC/Line Losses)

Home

FREE PDFs

🔍 Search