HCF calculator

Maximum Usable Frequency in F-region Calculator

Engineering Chemistry Financial Health More >>

↳

Electronics Chemical Engineering Civil Electrical More >>

⤿

Antenna and Wave Propogation Amplifiers Analog Communications Analog Electronics More >>

⤿

Wave Propagation Antenna Theory Parameters Special Antennas

✖Critical frequency is the highest magnitude of frequency above which the waves penetrate the ionosphere and below which the waves are reflected back from the ionosphere.ⓘ Critical Frequency [f_c]			+10% -10%
✖The Angle of incidence is the angle formed at the point of incidence between the incident ray and the normal is called the angle of incidence at layer of ionosphere.ⓘ Angle of Incidence [θ_i]			+10% -10%

✖Maximum Usable frequency is the highest radio frequency that can be used for transmission between two points via reflection from the ionosphere.ⓘ Maximum Usable Frequency in F-region [F_muf]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Wave Propagation Formulas PDF PDF Image

Maximum Usable Frequency in F-region Solution

STEP 0: Pre-Calculation Summary

Formula Used

Maximum Usable Frequency = Critical Frequency/cos(Angle of Incidence)
F_muf = f_c/cos(θ_i)
This formula uses 1 Functions, 3 Variables

Functions Used

cos - Cosine of an angle is the ratio of the side adjacent to the angle to the hypotenuse of the triangle., cos(Angle)

Variables Used

Maximum Usable Frequency - (Measured in Hertz) - Maximum Usable frequency is the highest radio frequency that can be used for transmission between two points via reflection from the ionosphere.
Critical Frequency - (Measured in Hertz) - Critical frequency is the highest magnitude of frequency above which the waves penetrate the ionosphere and below which the waves are reflected back from the ionosphere.
Angle of Incidence - (Measured in Radian) - The Angle of incidence is the angle formed at the point of incidence between the incident ray and the normal is called the angle of incidence at layer of ionosphere.

STEP 1: Convert Input(s) to Base Unit

Critical Frequency: 45 Hertz --> 45 Hertz No Conversion Required
Angle of Incidence: 83.85 Degree --> 1.46345857779697 Radian (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

F_muf = f_c/cos(θ_i) --> 45/cos(1.46345857779697)

Evaluating ... ...

F_muf = 420.04352759915

STEP 3: Convert Result to Output's Unit

420.04352759915 Hertz --> No Conversion Required

FINAL ANSWER

420.04352759915 ≈ 420.0435 Hertz <-- Maximum Usable Frequency

(Calculation completed in 00.006 seconds)

You are here -

Home » Engineering » Electronics » Antenna and Wave Propogation » Wave Propagation » Maximum Usable Frequency in F-region

Credits

Created by Bhuvana

BMS collegeof engineering (BMSCE), Benagluru

Bhuvana has created this Calculator and 25+ more calculators!

Verified by Rachita C

BMS College Of Engineering (BMSCE), Banglore

Rachita C has verified this Calculator and 50+ more calculators!

< Wave Propagation Calculators

Refractive Index of Ionosphere

LaTeX Go Refractive Index = sqrt(1-((81*Electron Density)/Operating Frequency^2))

Maximum Usable Frequency in F-region

LaTeX Go Maximum Usable Frequency = Critical Frequency/cos(Angle of Incidence)

Electron Density

LaTeX Go Electron Density = ((1-Refractive Index^2)*Operating Frequency^2)/81

Critical Frequency of Ionosphere

LaTeX Go Critical Frequency of Ionosphere = 9*sqrt(Electron Density)

Maximum Usable Frequency in F-region Formula

LaTeX Go

Maximum Usable Frequency = Critical Frequency/cos(Angle of Incidence)
F_muf = f_c/cos(θ_i)

MUF vs Critical frequency

Though critical frequency represents highest frequency which is reflected back from the layer at
vertical incidence; it is not highest frequency which is reflected from the layer.
The highest frequency which can be reflected depends on angle of incidence and on distance between transmitter and receiver antennas.

What is F - region of ionosphere?

F region, highest region of the ionosphere, at altitudes greater than 160 km (100 miles); it has the greatest concentration of free electrons and is the most important of the ionospheric regions.

How to Calculate Maximum Usable Frequency in F-region?

Maximum Usable Frequency in F-region calculator uses Maximum Usable Frequency = Critical Frequency/cos(Angle of Incidence) to calculate the Maximum Usable Frequency, Maximum Usable Frequency in F-region formula region refers to the highest frequency that can be effectively used for long-distance radio communication by reflecting off the F-region of the Earth's ionosphere. The F-region is the highest ionospheric layer, also known as the F2-layer, located approximately 200-400 km above the Earth's surface. Maximum Usable Frequency is denoted by F_muf symbol.

How to calculate Maximum Usable Frequency in F-region using this online calculator? To use this online calculator for Maximum Usable Frequency in F-region, enter Critical Frequency (f_c) & Angle of Incidence (θ_i) and hit the calculate button. Here is how the Maximum Usable Frequency in F-region calculation can be explained with given input values -> 420.0435 = 45/cos(1.46345857779697).

FAQ

What is Maximum Usable Frequency in F-region?

Maximum Usable Frequency in F-region formula region refers to the highest frequency that can be effectively used for long-distance radio communication by reflecting off the F-region of the Earth's ionosphere. The F-region is the highest ionospheric layer, also known as the F2-layer, located approximately 200-400 km above the Earth's surface and is represented as F_muf = f_c/cos(θ_i) or Maximum Usable Frequency = Critical Frequency/cos(Angle of Incidence). Critical frequency is the highest magnitude of frequency above which the waves penetrate the ionosphere and below which the waves are reflected back from the ionosphere & The Angle of incidence is the angle formed at the point of incidence between the incident ray and the normal is called the angle of incidence at layer of ionosphere.

How to calculate Maximum Usable Frequency in F-region?

Maximum Usable Frequency in F-region formula region refers to the highest frequency that can be effectively used for long-distance radio communication by reflecting off the F-region of the Earth's ionosphere. The F-region is the highest ionospheric layer, also known as the F2-layer, located approximately 200-400 km above the Earth's surface is calculated using Maximum Usable Frequency = Critical Frequency/cos(Angle of Incidence). To calculate Maximum Usable Frequency in F-region, you need Critical Frequency (f_c) & Angle of Incidence (θ_i). With our tool, you need to enter the respective value for Critical Frequency & Angle of Incidence and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Maximum Usable Frequency?

In this formula, Maximum Usable Frequency uses Critical Frequency & Angle of Incidence. We can use 1 other way(s) to calculate the same, which is/are as follows -

Maximum Usable Frequency = Critical Frequency*sqrt(1+(Skip Distance/(2*Ionospheric Layer Height))^2)

Home

FREE PDFs

🔍 Search