Lower Trigger Point Voltage in Square Wave Generator Calculator

✖Output Voltage is electrical voltage produced by the device after it has processed an input signal.ⓘ Output Voltage [V_out]			+10% -10%
✖Resistance 3 is the value of resistor 3 of the oscillator which resist the flow of current.ⓘ Resistance 3 [R₃]			+10% -10%
✖Resistance 2 is the value of resistor 2 of the oscillator.ⓘ Resistance 2 [R₂]			+10% -10%

✖Lower Trigger Voltage refers to a specific voltage level in a Schmitt trigger circuit.ⓘ Lower Trigger Point Voltage in Square Wave Generator [V_lt]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Electronics and Instrumentation Formula PDF PDF Image

Lower Trigger Point Voltage in Square Wave Generator Solution

STEP 0: Pre-Calculation Summary

Formula Used

Lower Trigger Voltage = Output Voltage*Resistance 3/(Resistance 2+Resistance 3)
V_lt = V_out*R₃/(R₂+R₃)
This formula uses 4 Variables

Variables Used

Lower Trigger Voltage - (Measured in Volt) - Lower Trigger Voltage refers to a specific voltage level in a Schmitt trigger circuit.
Output Voltage - (Measured in Volt) - Output Voltage is electrical voltage produced by the device after it has processed an input signal.
Resistance 3 - (Measured in Ohm) - Resistance 3 is the value of resistor 3 of the oscillator which resist the flow of current.
Resistance 2 - (Measured in Ohm) - Resistance 2 is the value of resistor 2 of the oscillator.

STEP 1: Convert Input(s) to Base Unit

Output Voltage: 1.8 Volt --> 1.8 Volt No Conversion Required
Resistance 3: 0.9 Ohm --> 0.9 Ohm No Conversion Required
Resistance 2: 0.5 Ohm --> 0.5 Ohm No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

V_lt = V_out*R₃/(R₂+R₃) --> 1.8*0.9/(0.5+0.9)

Evaluating ... ...

V_lt = 1.15714285714286

STEP 3: Convert Result to Output's Unit

1.15714285714286 Volt --> No Conversion Required

FINAL ANSWER

1.15714285714286 ≈ 1.157143 Volt <-- Lower Trigger Voltage

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electronics and Instrumentation » Signal Generator and Analyzer » Signal Converter » Lower Trigger Point Voltage in Square Wave Generator

Credits

Created by Nikita Suryawanshi

Vellore Institute of Technology (VIT), Vellore

Nikita Suryawanshi has created this Calculator and 100+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< Signal Converter Calculators

Output Voltage of Triangle to Sine Converter with Diode 1

LaTeX Go Output Voltage = Input Voltage*((Resistance 2*Resistance 3)/((Resistance 1*Resistance 2)+(Resistance 1*Resistance 3)+(Resistance 2*Resistance 3)))

Output Voltage of Triangle to Sine Converter with Diode 2

LaTeX Go Output Voltage = Input Voltage*((Resistance 2*Resistance 4)/((Resistance 1*Resistance 2)+(Resistance 1*Resistance 4)+(Resistance 2*Resistance 4)))

Upper Trigger Point Voltage in Triangle to Square Converter

LaTeX Go Upper Trigger Voltage = Output Voltage*(Resistance 3/(Resistance 2+Resistance 3))

Output Voltage of Triangle to Sine Converter without Diode 1 and Diode 2

LaTeX Go Output Voltage = Input Voltage*Resistance 2/(Resistance 1+Resistance 2)

Lower Trigger Point Voltage in Square Wave Generator Formula

LaTeX Go

Lower Trigger Voltage = Output Voltage*Resistance 3/(Resistance 2+Resistance 3)
V_lt = V_out*R₃/(R₂+R₃)

How does the state change at Lower Trigger Point in Triangle to Square Converter?

Lower Trigger Point in Triangle to Square Converter: When the input value is less than or equal to 10, the state changes to Square. This is because the Triangle shape is converted to a Square shape when the input value is less than or equal to 10.

How to Calculate Lower Trigger Point Voltage in Square Wave Generator?

Lower Trigger Point Voltage in Square Wave Generator calculator uses Lower Trigger Voltage = Output Voltage*Resistance 3/(Resistance 2+Resistance 3) to calculate the Lower Trigger Voltage, The Lower Trigger Point Voltage in Square Wave Generator formula is defined as the specific voltage level at which the output switches from high to low, initiating the falling edge of the square wave. Lower Trigger Voltage is denoted by V_lt symbol.

How to calculate Lower Trigger Point Voltage in Square Wave Generator using this online calculator? To use this online calculator for Lower Trigger Point Voltage in Square Wave Generator, enter Output Voltage (V_out), Resistance 3 (R₃) & Resistance 2 (R₂) and hit the calculate button. Here is how the Lower Trigger Point Voltage in Square Wave Generator calculation can be explained with given input values -> 1.157143 = 1.8*0.9/(0.5+0.9).

FAQ

What is Lower Trigger Point Voltage in Square Wave Generator?

The Lower Trigger Point Voltage in Square Wave Generator formula is defined as the specific voltage level at which the output switches from high to low, initiating the falling edge of the square wave and is represented as V_lt = V_out*R₃/(R₂+R₃) or Lower Trigger Voltage = Output Voltage*Resistance 3/(Resistance 2+Resistance 3). Output Voltage is electrical voltage produced by the device after it has processed an input signal, Resistance 3 is the value of resistor 3 of the oscillator which resist the flow of current & Resistance 2 is the value of resistor 2 of the oscillator.

How to calculate Lower Trigger Point Voltage in Square Wave Generator?

The Lower Trigger Point Voltage in Square Wave Generator formula is defined as the specific voltage level at which the output switches from high to low, initiating the falling edge of the square wave is calculated using Lower Trigger Voltage = Output Voltage*Resistance 3/(Resistance 2+Resistance 3). To calculate Lower Trigger Point Voltage in Square Wave Generator, you need Output Voltage (V_out), Resistance 3 (R₃) & Resistance 2 (R₂). With our tool, you need to enter the respective value for Output Voltage, Resistance 3 & Resistance 2 and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search