Lower Section of Drill String Length that is in Compression Calculator

✖Density of Drilling Mud considering a steel drilling pipe hanging in an oil well.ⓘ Density of Drilling Mud [ρ_m]			+10% -10%
✖Length of Pipe Hanging in Well is essential in calculating all other values required in drilling.ⓘ Length of Pipe Hanging in Well [L_Well]			+10% -10%
✖Mass Density of Steel varies based on the alloying constituents but usually ranges between 7,750 and 8,050 kg/m3.ⓘ Mass Density of Steel [ρ_s]			+10% -10%

✖Lower Section of Drill String Length that is in Compression depends on the density of the drilling mud, length of pipe in well and mass density of steel.ⓘ Lower Section of Drill String Length that is in Compression [L_c]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Hydrostatics Formulas PDF PDF Image

Lower Section of Drill String Length that is in Compression Solution

STEP 0: Pre-Calculation Summary

Formula Used

Lower Section of Drill String Length = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Mass Density of Steel
L_c = (ρ_m*L_Well)/ρ_s
This formula uses 4 Variables

Variables Used

Lower Section of Drill String Length - Lower Section of Drill String Length that is in Compression depends on the density of the drilling mud, length of pipe in well and mass density of steel.
Density of Drilling Mud - (Measured in Kilogram per Cubic Meter) - Density of Drilling Mud considering a steel drilling pipe hanging in an oil well.
Length of Pipe Hanging in Well - (Measured in Meter) - Length of Pipe Hanging in Well is essential in calculating all other values required in drilling.
Mass Density of Steel - (Measured in Kilogram per Cubic Meter) - Mass Density of Steel varies based on the alloying constituents but usually ranges between 7,750 and 8,050 kg/m3.

STEP 1: Convert Input(s) to Base Unit

Density of Drilling Mud: 1440 Kilogram per Cubic Meter --> 1440 Kilogram per Cubic Meter No Conversion Required
Length of Pipe Hanging in Well: 16 Meter --> 16 Meter No Conversion Required
Mass Density of Steel: 7750 Kilogram per Cubic Meter --> 7750 Kilogram per Cubic Meter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

L_c = (ρ_m*L_Well)/ρ_s --> (1440*16)/7750

Evaluating ... ...

L_c = 2.97290322580645

STEP 3: Convert Result to Output's Unit

2.97290322580645 --> No Conversion Required

FINAL ANSWER

2.97290322580645 ≈ 2.972903 <-- Lower Section of Drill String Length

(Calculation completed in 00.018 seconds)

You are here -

Home » Engineering » Civil » Coastal and Ocean Engineering » Offshore Hydromechanics » Hydrostatics » Lower Section of Drill String Length that is in Compression

Credits

Created by Mithila Muthamma PA

Coorg Institute of Technology (CIT), Coorg

Mithila Muthamma PA has created this Calculator and 2000+ more calculators!

Verified by M Naveen

National Institute of Technology (NIT), Warangal

M Naveen has verified this Calculator and 900+ more calculators!

< Hydrostatics Calculators

Coordinate measured Downward from Top given Tension on Vertical Drill String

LaTeX Go Coordinate measured Downward from Top = -((Tension on Vertical Drill String/(Mass Density of Steel*[g]*Cross Section Area of Steel in Pipe))-Length of Pipe Hanging in Well)

Cross Section Area of Steel in Pipe given Tension on Vertical Drill String

LaTeX Go Cross Section Area of Steel in Pipe = Tension on Vertical Drill String/(Mass Density of Steel*[g]*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))

Mass Density of Steel for Tension on Vertical Drill String

LaTeX Go Mass Density of Steel = Tension on Vertical Drill String/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))

Tension on Vertical Drill String

LaTeX Go Tension on Vertical Drill String = Mass Density of Steel*[g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top)

Lower Section of Drill String Length that is in Compression Formula

LaTeX Go

Lower Section of Drill String Length = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Mass Density of Steel
L_c = (ρ_m*L_Well)/ρ_s

What is Buoyancy?

Buoyancy is the force that causes objects to float. It is the force exerted on an object that is partly or wholly immersed in a fluid. Buoyancy is caused by the differences in pressure acting on opposite sides of an object immersed in a static fluid. It is also known as the buoyant force.

How to Calculate Lower Section of Drill String Length that is in Compression?

Lower Section of Drill String Length that is in Compression calculator uses Lower Section of Drill String Length = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Mass Density of Steel to calculate the Lower Section of Drill String Length, Lower Section of Drill String Length that is in Compression is when there will be no axial force in the drill string at an elevation above its bottom end and that the entire length below that point will be in compression. Lower Section of Drill String Length is denoted by L_c symbol.

How to calculate Lower Section of Drill String Length that is in Compression using this online calculator? To use this online calculator for Lower Section of Drill String Length that is in Compression, enter Density of Drilling Mud (ρ_m), Length of Pipe Hanging in Well (L_Well) & Mass Density of Steel (ρ_s) and hit the calculate button. Here is how the Lower Section of Drill String Length that is in Compression calculation can be explained with given input values -> 2.972903 = (1440*16)/7750.

FAQ

What is Lower Section of Drill String Length that is in Compression?

Lower Section of Drill String Length that is in Compression is when there will be no axial force in the drill string at an elevation above its bottom end and that the entire length below that point will be in compression and is represented as L_c = (ρ_m*L_Well)/ρ_s or Lower Section of Drill String Length = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Mass Density of Steel. Density of Drilling Mud considering a steel drilling pipe hanging in an oil well, Length of Pipe Hanging in Well is essential in calculating all other values required in drilling & Mass Density of Steel varies based on the alloying constituents but usually ranges between 7,750 and 8,050 kg/m3.

How to calculate Lower Section of Drill String Length that is in Compression?

Lower Section of Drill String Length that is in Compression is when there will be no axial force in the drill string at an elevation above its bottom end and that the entire length below that point will be in compression is calculated using Lower Section of Drill String Length = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Mass Density of Steel. To calculate Lower Section of Drill String Length that is in Compression, you need Density of Drilling Mud (ρ_m), Length of Pipe Hanging in Well (L_Well) & Mass Density of Steel (ρ_s). With our tool, you need to enter the respective value for Density of Drilling Mud, Length of Pipe Hanging in Well & Mass Density of Steel and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search