Losses in Nominal T Method Calculator

✖Resistance in T is a measure of the opposition to current flow in a medium length transmission line.ⓘ Resistance in T [R_t]			+10% -10%
✖Receiving End Current in T is defined as the magnitude and phase angle of current received at the load end of a medium transmission line.ⓘ Receiving End Current in T [I_r(t)]			+10% -10%
✖Sending End Current in T is defined as the amount of current injected into a medium transmission line from the source or injectors.ⓘ Sending End Current in T [I_s(t)]			+10% -10%

✖Power Loss in T is defined as the deviation in the power transferred from sending end to receiving end of a medium transmission line.ⓘ Losses in Nominal T Method [P_loss(t)]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Nominal T Method in Medium Line Formulas PDF PDF Image

Losses in Nominal T Method Solution

STEP 0: Pre-Calculation Summary

Formula Used

Power Loss in T = 3*(Resistance in T/2)*(Receiving End Current in T^2+Sending End Current in T^2)
P_loss(t) = 3*(R_t/2)*(I_r(t)^2+I_s(t)^2)
This formula uses 4 Variables

Variables Used

Power Loss in T - (Measured in Watt) - Power Loss in T is defined as the deviation in the power transferred from sending end to receiving end of a medium transmission line.
Resistance in T - (Measured in Ohm) - Resistance in T is a measure of the opposition to current flow in a medium length transmission line.
Receiving End Current in T - (Measured in Ampere) - Receiving End Current in T is defined as the magnitude and phase angle of current received at the load end of a medium transmission line.
Sending End Current in T - (Measured in Ampere) - Sending End Current in T is defined as the amount of current injected into a medium transmission line from the source or injectors.

STEP 1: Convert Input(s) to Base Unit

Resistance in T: 7.52 Ohm --> 7.52 Ohm No Conversion Required
Receiving End Current in T: 14.72 Ampere --> 14.72 Ampere No Conversion Required
Sending End Current in T: 16.2 Ampere --> 16.2 Ampere No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

P_loss(t) = 3*(R_t/2)*(I_r(t)^2+I_s(t)^2) --> 3*(7.52/2)*(14.72^2+16.2^2)

Evaluating ... ...

P_loss(t) = 5404.455552

STEP 3: Convert Result to Output's Unit

5404.455552 Watt --> No Conversion Required

FINAL ANSWER

5404.455552 ≈ 5404.456 Watt <-- Power Loss in T

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Power System » Transmission Lines » Medium Line » Nominal T Method in Medium Line » Losses in Nominal T Method

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< Nominal T Method in Medium Line Calculators

Receiving End Angle using Sending End Power in Nominal T Method

LaTeX Go Receiving End Phase Angle in T = acos((Sending End Power in T-Power Loss in T)/(Receiving End Voltage in T*Receiving End Current in T*3))

Sending End Current using Losses in Nominal T Method

LaTeX Go Sending End Current in T = sqrt((Power Loss in T/(3/2)*Resistance in T)-(Receiving End Current in T^2))

Capacitive Voltage in Nominal T Method

LaTeX Go Capacitive Voltage in T = Receiving End Voltage in T+(Receiving End Current in T*Impedance in T/2)

Losses in Nominal T Method

LaTeX Go Power Loss in T = 3*(Resistance in T/2)*(Receiving End Current in T^2+Sending End Current in T^2)

Losses in Nominal T Method Formula

LaTeX Go

Power Loss in T = 3*(Resistance in T/2)*(Receiving End Current in T^2+Sending End Current in T^2)
P_loss(t) = 3*(R_t/2)*(I_r(t)^2+I_s(t)^2)

Which of the following transmission line can be considered as a medium transmission line?

The transmission lines having a length of more than ₈₀ Km and less than ₂₀₀ Km are considered medium transmission lines. Their operating voltage is more than short transmission lines but less than long transmission lines.

How to Calculate Losses in Nominal T Method?

Losses in Nominal T Method calculator uses Power Loss in T = 3*(Resistance in T/2)*(Receiving End Current in T^2+Sending End Current in T^2) to calculate the Power Loss in T, The Losses in Nominal T method formula is defined as the ratio of the power absorbed by the input circuit of a transducer to the power delivered to a specified load; usually expressed in decibels. Power Loss in T is denoted by P_loss(t) symbol.

How to calculate Losses in Nominal T Method using this online calculator? To use this online calculator for Losses in Nominal T Method, enter Resistance in T (R_t), Receiving End Current in T (I_r(t)) & Sending End Current in T (I_s(t)) and hit the calculate button. Here is how the Losses in Nominal T Method calculation can be explained with given input values -> 5331.812 = 3*(7.52/2)*(14.72^2+16.2^2).

FAQ

What is Losses in Nominal T Method?

The Losses in Nominal T method formula is defined as the ratio of the power absorbed by the input circuit of a transducer to the power delivered to a specified load; usually expressed in decibels and is represented as P_loss(t) = 3*(R_t/2)*(I_r(t)^2+I_s(t)^2) or Power Loss in T = 3*(Resistance in T/2)*(Receiving End Current in T^2+Sending End Current in T^2). Resistance in T is a measure of the opposition to current flow in a medium length transmission line, Receiving End Current in T is defined as the magnitude and phase angle of current received at the load end of a medium transmission line & Sending End Current in T is defined as the amount of current injected into a medium transmission line from the source or injectors.

How to calculate Losses in Nominal T Method?

The Losses in Nominal T method formula is defined as the ratio of the power absorbed by the input circuit of a transducer to the power delivered to a specified load; usually expressed in decibels is calculated using Power Loss in T = 3*(Resistance in T/2)*(Receiving End Current in T^2+Sending End Current in T^2). To calculate Losses in Nominal T Method, you need Resistance in T (R_t), Receiving End Current in T (I_r(t)) & Sending End Current in T (I_s(t)). With our tool, you need to enter the respective value for Resistance in T, Receiving End Current in T & Sending End Current in T and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search