Load Resistance of CS Amplifier Calculator

✖Output voltage signifies the voltage of the signal after it has been amplified.ⓘ Output Voltage [V_out]			+10% -10%
✖Transconductance is the ratio of the change in current at the output terminal to the change in the voltage at the input terminal of an active device.ⓘ Transconductance [g_m]			+10% -10%
✖Gate to source voltage of transistor is the voltage that falls across the gate-source terminal of the transistor.ⓘ Gate to Source Voltage [V_gs]			+10% -10%

✖Load resistance is the cumulative resistance of a circuit, as seen by the voltage, current, or power source driving that circuit.ⓘ Load Resistance of CS Amplifier [R_L]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download High Frequency Response Amplifiers Formula PDF PDF Image

Load Resistance of CS Amplifier Solution

STEP 0: Pre-Calculation Summary

Formula Used

Load Resistance = (Output Voltage/(Transconductance*Gate to Source Voltage))
R_L = (V_out/(g_m*V_gs))
This formula uses 4 Variables

Variables Used

Load Resistance - (Measured in Ohm) - Load resistance is the cumulative resistance of a circuit, as seen by the voltage, current, or power source driving that circuit.
Output Voltage - (Measured in Volt) - Output voltage signifies the voltage of the signal after it has been amplified.
Transconductance - (Measured in Siemens) - Transconductance is the ratio of the change in current at the output terminal to the change in the voltage at the input terminal of an active device.
Gate to Source Voltage - (Measured in Volt) - Gate to source voltage of transistor is the voltage that falls across the gate-source terminal of the transistor.

STEP 1: Convert Input(s) to Base Unit

Output Voltage: 28.78 Volt --> 28.78 Volt No Conversion Required
Transconductance: 4.8 Millisiemens --> 0.0048 Siemens (Check conversion here)
Gate to Source Voltage: 4 Volt --> 4 Volt No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

R_L = (V_out/(g_m*V_gs)) --> (28.78/(0.0048*4))

Evaluating ... ...

R_L = 1498.95833333333

STEP 3: Convert Result to Output's Unit

1498.95833333333 Ohm -->1.49895833333333 Kilohm (Check conversion here)

FINAL ANSWER

1.49895833333333 ≈ 1.498958 Kilohm <-- Load Resistance

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Electronics » Amplifiers » High Frequency Response Amplifiers » Response of CS Amplifier » Load Resistance of CS Amplifier

Credits

Created by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has created this Calculator and 600+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Response of CS Amplifier Calculators

Output Voltage of CS Amplifier

LaTeX Go Output Voltage = Transconductance*Gate to Source Voltage*Load Resistance

Equivalent Signal Resistance of CS Amplifier

LaTeX Go Internal Small Signal Resistance = 1/((1/Signal Resistance+1/Output Resistance))

Frequency of Zero Transmission of CS Amplifier

LaTeX Go Transmission Frequency = 1/(Bypass Capacitor*Signal Resistance)

Midband Gain of CS Amplifier

LaTeX Go Mid Band Gain = Output Voltage/Small Signal Voltage

< Common Stage Amplifiers Calculators

Effective High Frequency Time Constant of CE Amplifier

LaTeX Go Effective High Frequency Time Constant = Base Emitter Capacitance*Signal Resistance+(Collector Base Junction Capacitance*(Signal Resistance*(1+Transconductance*Load Resistance)+Load Resistance))+(Capacitance*Load Resistance)

High-Frequency Band given Complex Frequency Variable

LaTeX Go Amplifier Gain in Mid Band = sqrt(((1+(3 dB Frequency/Frequency))*(1+(3 dB Frequency/Frequency Observed)))/((1+(3 dB Frequency/Pole Frequency))*(1+(3 dB Frequency/Second Pole Frequency))))

Collector Base Junction Resistance of CE Amplifier

LaTeX Go Collector Resistance = Signal Resistance*(1+Transconductance*Load Resistance)+Load Resistance

Amplifier Bandwidth in Discrete-Circuit Amplifier

LaTeX Go Amplifier Bandwidth = High Frequency-Low Frequency

Load Resistance of CS Amplifier Formula

LaTeX Go

Load Resistance = (Output Voltage/(Transconductance*Gate to Source Voltage))
R_L = (V_out/(g_m*V_gs))

What is CS amplifier?

In electronics, a common-source amplifier is one of three basic single-stage field-effect transistor (FET) amplifier topologies, typically used as a voltage or transconductance amplifier. The easiest way to tell if a FET is a common source, common drain, or common gate is to examine where the signal enters and leaves.

How to Calculate Load Resistance of CS Amplifier?

Load Resistance of CS Amplifier calculator uses Load Resistance = (Output Voltage/(Transconductance*Gate to Source Voltage)) to calculate the Load Resistance, Load Resistance of CS Amplifier is the resistance that is placed in series with the output circuit of the amplifier. This resistance is used to match the impedance of the amplifier to the load it is driving, ensuring maximum power transfer and minimum distortion. Load Resistance is denoted by R_L symbol.

How to calculate Load Resistance of CS Amplifier using this online calculator? To use this online calculator for Load Resistance of CS Amplifier, enter Output Voltage (V_out), Transconductance (g_m) & Gate to Source Voltage (V_gs) and hit the calculate button. Here is how the Load Resistance of CS Amplifier calculation can be explained with given input values -> 0.001499 = (28.78/(0.0048*4)).

FAQ

What is Load Resistance of CS Amplifier?

Load Resistance of CS Amplifier is the resistance that is placed in series with the output circuit of the amplifier. This resistance is used to match the impedance of the amplifier to the load it is driving, ensuring maximum power transfer and minimum distortion and is represented as R_L = (V_out/(g_m*V_gs)) or Load Resistance = (Output Voltage/(Transconductance*Gate to Source Voltage)). Output voltage signifies the voltage of the signal after it has been amplified, Transconductance is the ratio of the change in current at the output terminal to the change in the voltage at the input terminal of an active device & Gate to source voltage of transistor is the voltage that falls across the gate-source terminal of the transistor.

How to calculate Load Resistance of CS Amplifier?

Load Resistance of CS Amplifier is the resistance that is placed in series with the output circuit of the amplifier. This resistance is used to match the impedance of the amplifier to the load it is driving, ensuring maximum power transfer and minimum distortion is calculated using Load Resistance = (Output Voltage/(Transconductance*Gate to Source Voltage)). To calculate Load Resistance of CS Amplifier, you need Output Voltage (V_out), Transconductance (g_m) & Gate to Source Voltage (V_gs). With our tool, you need to enter the respective value for Output Voltage, Transconductance & Gate to Source Voltage and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Load Resistance?

In this formula, Load Resistance uses Output Voltage, Transconductance & Gate to Source Voltage. We can use 1 other way(s) to calculate the same, which is/are as follows -

Load Resistance = Resistance*(1+(Transconductance*Finite Input Resistance))-Finite Input Resistance

Home

FREE PDFs

🔍 Search