Length of Span for Maximum Angular Distortion of Fillet Welds Calculator

✖Maximum Distortion is the maximum deformation of fillet weld possible in restricted position.ⓘ Maximum Distortion [δ_max]			+10% -10%
✖Angular change in restrained joints is the angles introduced by wavy distortions due to restrictions on fillet welds.ⓘ Angular Change in Restrained Joints [φ]			+10% -10%

✖Length of Span of The Fillet Welds is the distance between two consecutive fillet welds.ⓘ Length of Span for Maximum Angular Distortion of Fillet Welds [L]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Distortion in Weldments Formulas PDF PDF Image

Length of Span for Maximum Angular Distortion of Fillet Welds Solution

STEP 0: Pre-Calculation Summary

Formula Used

Length of Span of The Fillet Welds = Maximum Distortion/(0.25*Angular Change in Restrained Joints)
L = δ_max/(0.25*φ)
This formula uses 3 Variables

Variables Used

Length of Span of The Fillet Welds - (Measured in Meter) - Length of Span of The Fillet Welds is the distance between two consecutive fillet welds.
Maximum Distortion - (Measured in Meter) - Maximum Distortion is the maximum deformation of fillet weld possible in restricted position.
Angular Change in Restrained Joints - (Measured in Radian) - Angular change in restrained joints is the angles introduced by wavy distortions due to restrictions on fillet welds.

STEP 1: Convert Input(s) to Base Unit

Maximum Distortion: 1.5 Millimeter --> 0.0015 Meter (Check conversion here)
Angular Change in Restrained Joints: 1.2 Radian --> 1.2 Radian No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

L = δ_max/(0.25*φ) --> 0.0015/(0.25*1.2)

Evaluating ... ...

L = 0.005

STEP 3: Convert Result to Output's Unit

0.005 Meter -->5 Millimeter (Check conversion here)

FINAL ANSWER

5 Millimeter <-- Length of Span of The Fillet Welds

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Production Engineering » Welding » Distortion in Weldments » Angular Distortion » Length of Span for Maximum Angular Distortion of Fillet Welds

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Nishan Poojary

Shri Madhwa Vadiraja Institute of Technology and Management (SMVITM), Udupi

Nishan Poojary has verified this Calculator and 400+ more calculators!

< Angular Distortion Calculators

Angular Distortion at x of Fillet Welds

LaTeX Go Distortion at Some Distance = Length of Span of The Fillet Welds*(0.25*Angular Change in Restrained Joints-Angular Change in Restrained Joints*(Distance from the Center Line of the Frame/Length of Span of The Fillet Welds-0.5)^2)

Angular Change when there is Maximum Distortion of Fillet Welds

LaTeX Go Angular Change in Restrained Joints = Maximum Distortion/(0.25*Length of Span of The Fillet Welds)

Length of Span for Maximum Angular Distortion of Fillet Welds

LaTeX Go Length of Span of The Fillet Welds = Maximum Distortion/(0.25*Angular Change in Restrained Joints)

Maximum Angular Distortion of Fillet Welds

LaTeX Go Maximum Distortion = 0.25*Angular Change in Restrained Joints*Length of Span of The Fillet Welds

Length of Span for Maximum Angular Distortion of Fillet Welds Formula

LaTeX Go

Length of Span of The Fillet Welds = Maximum Distortion/(0.25*Angular Change in Restrained Joints)
L = δ_max/(0.25*φ)

What is called Distortion in welding terms ?

One of the major problems found with weldments is the distortion. Distortion is caused mainly because of the shrinkage that take place in weldments. The shrinkage taking place in a weldment depends upon the geometry and type of the weld. There are three types of distortions possible in weldments.
(a) Transverse shrinkage occurring perpendicular to the weld line.
(b) Longitudinal shrinkage occurring parallel to the weld line, which is very small of the order of about 0.1% of the weld length and hence can be neglected.
(c) Angular change as a rotation about the weld line.

How to Calculate Length of Span for Maximum Angular Distortion of Fillet Welds?

Length of Span for Maximum Angular Distortion of Fillet Welds calculator uses Length of Span of The Fillet Welds = Maximum Distortion/(0.25*Angular Change in Restrained Joints) to calculate the Length of Span of The Fillet Welds, The Length of Span for Maximum Angular Distortion of Fillet Welds formula is defined as the distance between consecutive fillet welds. Length of Span of The Fillet Welds is denoted by L symbol.

How to calculate Length of Span for Maximum Angular Distortion of Fillet Welds using this online calculator? To use this online calculator for Length of Span for Maximum Angular Distortion of Fillet Welds, enter Maximum Distortion (δ_max) & Angular Change in Restrained Joints (φ) and hit the calculate button. Here is how the Length of Span for Maximum Angular Distortion of Fillet Welds calculation can be explained with given input values -> 5000 = 0.0015/(0.25*1.2).

FAQ

What is Length of Span for Maximum Angular Distortion of Fillet Welds?

The Length of Span for Maximum Angular Distortion of Fillet Welds formula is defined as the distance between consecutive fillet welds and is represented as L = δ_max/(0.25*φ) or Length of Span of The Fillet Welds = Maximum Distortion/(0.25*Angular Change in Restrained Joints). Maximum Distortion is the maximum deformation of fillet weld possible in restricted position & Angular change in restrained joints is the angles introduced by wavy distortions due to restrictions on fillet welds.

How to calculate Length of Span for Maximum Angular Distortion of Fillet Welds?

The Length of Span for Maximum Angular Distortion of Fillet Welds formula is defined as the distance between consecutive fillet welds is calculated using Length of Span of The Fillet Welds = Maximum Distortion/(0.25*Angular Change in Restrained Joints). To calculate Length of Span for Maximum Angular Distortion of Fillet Welds, you need Maximum Distortion (δ_max) & Angular Change in Restrained Joints (φ). With our tool, you need to enter the respective value for Maximum Distortion & Angular Change in Restrained Joints and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search