Length of Reach given Average Energy Slope for Non-Uniform Flow Calculator

✖Frictional Loss is the loss of pressure or “head” that occurs in pipe or duct flow due to the effect of the fluid's viscosity near the surface of the pipe or duct.ⓘ Frictional Loss [h_f]			+10% -10%
✖Average Energy Slope is at a distance equal to the velocity head above the hydraulic gradient.ⓘ Average Energy Slope [S_favg]			+10% -10%

✖Reach in practical use is any length of a stream or river. The term is often used when referring to a small section of a stream or river rather than its entire length.ⓘ Length of Reach given Average Energy Slope for Non-Uniform Flow [L]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Indirect Methods of Streamflow Measurement Formulas PDF PDF Image

Length of Reach given Average Energy Slope for Non-Uniform Flow Solution

STEP 0: Pre-Calculation Summary

Formula Used

Reach = Frictional Loss/Average Energy Slope
L = h_f/S_favg
This formula uses 3 Variables

Variables Used

Reach - (Measured in Meter) - Reach in practical use is any length of a stream or river. The term is often used when referring to a small section of a stream or river rather than its entire length.
Frictional Loss - Frictional Loss is the loss of pressure or “head” that occurs in pipe or duct flow due to the effect of the fluid's viscosity near the surface of the pipe or duct.
Average Energy Slope - Average Energy Slope is at a distance equal to the velocity head above the hydraulic gradient.

STEP 1: Convert Input(s) to Base Unit

Frictional Loss: 15 --> No Conversion Required
Average Energy Slope: 1.5 --> No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

L = h_f/S_favg --> 15/1.5

Evaluating ... ...

L = 10

STEP 3: Convert Result to Output's Unit

10 Meter --> No Conversion Required

FINAL ANSWER

10 Meter <-- Reach

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Civil » Engineering Hydrology » Indirect Methods of Streamflow Measurement » Slope Area Method » Non Uniform Flow » Length of Reach given Average Energy Slope for Non-Uniform Flow

Credits

Created by Mithila Muthamma PA

Coorg Institute of Technology (CIT), Coorg

Mithila Muthamma PA has created this Calculator and 2000+ more calculators!

Verified by Chandana P Dev

NSS College of Engineering (NSSCE), Palakkad

Chandana P Dev has verified this Calculator and 1700+ more calculators!

< Non Uniform Flow Calculators

Conveyance of Channel at End Sections at 1

LaTeX Go Conveyance of Channel at End Sections at (1) = (1/Manning’s Roughness Coefficient)*Area of Channel Section 1*Hydraulics Radius of Channel Section 1^(2/3)

Length of Reach given Average Energy Slope for Non-Uniform Flow

LaTeX Go Reach = Frictional Loss/Average Energy Slope

Frictional Loss given Average Energy Slope

LaTeX Go Frictional Loss = Average Energy Slope*Reach

Average Energy Slope given Frictional Loss

LaTeX Go Average Energy Slope = Frictional Loss/Reach

Length of Reach given Average Energy Slope for Non-Uniform Flow Formula

LaTeX Go

Reach = Frictional Loss/Average Energy Slope
L = h_f/S_favg

What is Slope Area method for Uniform Flow in Open Channel?

Slope Area method for Uniform Flow in Open Channel is when discharge is computed on the basis of a uniform flow equation involving channel characteristics, water surface profile and a roughness coefficient. The drop in water surface profile for a uniform reach of channel represents losses caused by bed roughness.

What is Non-Uniform Flow?

Flow is said to be non-uniform, when there is a change in the velocity of the flow at different points in a flowing fluid, for a given time. For example, the flow of liquids under pressure through long pipelines of varying diameters is referred to as non-uniform flow.

How to Calculate Length of Reach given Average Energy Slope for Non-Uniform Flow?

Length of Reach given Average Energy Slope for Non-Uniform Flow calculator uses Reach = Frictional Loss/Average Energy Slope to calculate the Reach, The Length of Reach given Average Energy Slope for Non-Uniform Flow formula is defined as the length of channel uniform concerning discharge, depth, area, and slope. The channel length for which a single gauge affords a satisfactory measure of the stage and discharge. Reach is denoted by L symbol.

How to calculate Length of Reach given Average Energy Slope for Non-Uniform Flow using this online calculator? To use this online calculator for Length of Reach given Average Energy Slope for Non-Uniform Flow, enter Frictional Loss (h_f) & Average Energy Slope (S_favg) and hit the calculate button. Here is how the Length of Reach given Average Energy Slope for Non-Uniform Flow calculation can be explained with given input values -> 10 = 15/1.5.

FAQ

What is Length of Reach given Average Energy Slope for Non-Uniform Flow?

The Length of Reach given Average Energy Slope for Non-Uniform Flow formula is defined as the length of channel uniform concerning discharge, depth, area, and slope. The channel length for which a single gauge affords a satisfactory measure of the stage and discharge and is represented as L = h_f/S_favg or Reach = Frictional Loss/Average Energy Slope. Frictional Loss is the loss of pressure or “head” that occurs in pipe or duct flow due to the effect of the fluid's viscosity near the surface of the pipe or duct & Average Energy Slope is at a distance equal to the velocity head above the hydraulic gradient.

How to calculate Length of Reach given Average Energy Slope for Non-Uniform Flow?

The Length of Reach given Average Energy Slope for Non-Uniform Flow formula is defined as the length of channel uniform concerning discharge, depth, area, and slope. The channel length for which a single gauge affords a satisfactory measure of the stage and discharge is calculated using Reach = Frictional Loss/Average Energy Slope. To calculate Length of Reach given Average Energy Slope for Non-Uniform Flow, you need Frictional Loss (h_f) & Average Energy Slope (S_favg). With our tool, you need to enter the respective value for Frictional Loss & Average Energy Slope and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search